View source for QSG 2025 06 20

This Wiki page contains the online version of the '''Quick Start Guide (QSG)''' for the '''ATRM50 5G Transport Router'''. Here you will find an overview of the various components on the front and back of a ATRM50 device, hardware installation instructions, first login information, device specifications, and general safety information. It is highly recommended to acquaint yourself with the Quick Start Guide before using the device. You can also locate a printed version of the Quick Start Guide in the packaging box of your device.

<table>
    <tr>

   <td style="border-bottom: 0px solid #e8e8e8; vertical-align: top; margin: 10px; padding-right: 50px;">__TOC__</td>        
   <td style="vertical-align: top; margin: 10px; padding-top: 25px; padding-right: 50px;">[[File:ATRM50 TOP.png|right|340px]]</td>
   <td style="vertical-align: top; margin: 10px; padding-top: 75px; padding-right: 50px;">[[File:ATRM50 Sides.png|right|440px]]</td>
    </tr>
</table>

= Safety information =

Before starting operating the device, please review recommendations and precautions to minimize the possibility of accidents. Safety precautions presented are supplementary and subject to the local safety regulations. When various operations are executed on the device, the user must fully follow the safety instructions and recommendations provided with the device.

== General ==
{| class="wikitable"
|- style="font-weight:bold;"
! colspan="2" | Radio specifications
|-
|RF technologies
|3G, 4G, 5G, WiFi, GNSS
|-
|Max RF power
|25dBm@WCDMA, 28dBm@LTE, 28dBm @5G, 20dBm@WiFi 2.4G, 23dBm@WiFi 5G
|- style="font-weight:bold;"
| colspan="2" style="text-align:center;" | Bundled accessories speciﬁcations*
|-
|Mobile antenna
|617~960/1400~2690/3300~5900MHz, VSWR<3, gain <4dBi, Omidirectional, SMA male connector
|-
|WiFi antenna
|2400~2500 /4950~5850 MHz, 50Ω, VSWR≤2, gain** 3dBi, omnidirectional, RP-SMA male connector
|-
|GNSS antenna
|1575.42~1602 MHz, 2.2~5 VDC, VSWR<1.5, active total gain** 27 dB (typ.), RHCP polarization, SMA male connector
|}

<small><nowiki>*</nowiki> Order code dependant.</small>

<small><nowiki>**</nowiki> Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.</small>

=Compliance=

ATRM50 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.

==CE Declaration of Conformity==

{| class="wikitable" style="text-align:left;"
|- 
| style="font-weight:bold;" | [BG] Bulgarian
|С настоящото TELTONIKA NETWORKS декларира, че този ATRM50 е в съответствие със съществените изисквания и други разпоредби на Директиви 2014/53/ЕU, 2011/65/ЕU, 2009/125/EC.
|-
| style="font-weight:bold;" | [HR] Croatian
|Ovim TELTONIKA NETWORKS izjavljuje da je ovaj ATRM50 u skladu s bitnim zahtjevima i ostalim relevantnim odredbama Direktive 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [CZ] Czech
|Společnost TELTONIKA NETWORKS tímto prohlašuje, že tento ATRM50 splňuje základní požadavky a další ustanovení směrnic 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [DK] Danish
|TELTONIKA NETWORKS erklærer hermed, at denne ATRM50 er i overensstemmelse med de væsentlige krav og andre bestemmelser i direktiv 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [NL] Dutch
|Hereby, TELTONIKA NETWORKS declares that this ATRM50 is in compliance with the essential requirements and other relevant provisions of Richtlijnen 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [EE] Estonian
|Käesolevaga kinnitab TELTONIKA NETWORKS seadme ATRM50 vastavust Direktiivide 2014/53/EU, 2011/65/EU, 2009/125/EC põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
|-
| style="font-weight:bold;" | [FI] Finish
|TELTONIKA NETWORKS vakuuttaa täten että ATRM50 tyyppinen laite on Direktiivien 2014/53/EU, 2011/65/EU, 2009/125/EC oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
|-
| style="font-weight:bold;" | [FR] French
|TELTONIKA NETWORKS déclare par la présente que ce ATRM50 est conforme aux exigences essentielles et autres dispositions des Directives 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [DE] German
|TELTONIKA NETWORKS erklärt hiermit, dass dieses ATRM50 den grundlegenden Anforderungen und anderen Bestimmungen der Richtlinien 2014/53/EU, 2011/65/EU, 2009/125/EC entspricht.
|-
| style="font-weight:bold;" | [GR] Greek
|Η TELTONIKA NETWORKS δηλώνει ότι το παρόν ATRM50 συμμορφώνεται με τις βασικές απαιτήσεις και άλλες διατάξεις των Οδηγιών 2014/53/ΕU, 2011/65/ΕU, 2009/125/EC.
|-
| style="font-weight:bold;" | [HU] Hungarian
|A TELTONIKA NETWORKS kijelenti, hogy ez a ATRM50 megfelel a 2014/53/EU, 2011/65/EU, 2009/125/EC irányelvek alapvető követelményeinek és egyéb rendelkezéseinek.
|-
| style="font-weight:bold;" | [IE] Irish
|Leis seo, dearbhaíonn TELTONIKA NETWORKS go gcomhlíonann an ATRM50 seo bunriachtanais agus forálacha ábhartha eile Threoir 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [IT] Italian
|Con la presente, TELTONIKA NETWORKS dichiara che questo ATRM50 è conforme ai requisiti essenziali e ad altre disposizioni pertinenti della Direttive 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [LV] Latvian
|TELTONIKA NETWORKS ar šo paziņo, ka šis ATRM50 atbilst pamatprasībām un citiem Direktīvas 2014/53/EU, 2011/65/EU, 2009/125/EC noteikumiem.
|-
| style="font-weight:bold;" | [LT] Lithuanian
|Šiuo dokumentu UAB TELTONIKA NETWORKS deklaruoja, kad šis ATRM50 atitinka esminius reikalavimus ir kitas 2014/53/EU, 2011/65/EU, 2009/125/EC Direktyvų nuostatas.
|-
| style="font-weight:bold;" | [MT] Maltese
|TELTONIKA NETWORKS b'dan tiddikjara li dan ATRM50 jikkonforma mar-rekwiżiti essenzjali u dispożizzjonijiet oħra tad-Direttivi 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [NO] Norwegian
|TELTONIKA NETWORKS erklærer herved at denne ATRM50 er i samsvar med de grunnleggende kravene og andre bestemmelser i Direktivene 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [PL] Polish
|TELTONIKA NETWORKS niniejszym oświadcza, że niniejszy ATRM50 jest zgodny z zasadniczymi wymaganiami i innymi postanowieniami Dyrektyw 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [PT] Portuguese
|A TELTONIKA NETWORKS declara que esta ATRM50 cumpre os requisitos essenciais e outras disposições das Directivas 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [RO] Romanian
|TELTONIKA NETWORKS declară prin prezenta că acest ATRM50 este în conformitate cu cerințele esențiale și cu alte dispoziții ale Directivelor 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [SK] Slovak
|Spoločnosť TELTONIKA NETWORKS týmto vyhlasuje, že tento ATRM50 spĺňa základné požiadavky a ďalšie ustanovenia smerníc 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [SI] Slovenian
|TELTONIKA NETWORKS izjavlja, da je ta ATRM50 skladen z bistvenimi zahtevami in drugimi določbami Direktiv 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [ES] Spanish
|TELTONIKA NETWORKS declara por la presente que este ATRM50 cumple los requisitos esenciales y otras disposiciones de las Directivas 2014/53/EU, 2011/65/EU, 2009/125/EC.
|-
| style="font-weight:bold;" | [SE] Swedish
|TELTONIKA NETWORKS förklarar härmed att denna ATRM50 uppfyller de grundläggande kraven och andra bestämmelser i Direktiven 2014/53/EU och 2011/65/EU, 2009/125/EC.
|}

{{Template: Markings RF function with PSU
<!------------------------DEVICE----------------------->
| device         = ATRM50
}}

== RF exposure ==

This device meets the official requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by authorized agencies. The device must be used with a minimum separation of 20 cm from a person’s body to ensure compliance with RF exposure guidelines. Failure to observe these instructions could result in your RF exposure exceeding the applicable limits.

External antennas used with ATRM50 must be installed to provide a distance of at least 20 cm from any people and must not be co-located or operated in conjunction with any other antenna or transmitter.

Any external antenna gain must meet RF exposure and maximum radiated output power limits of the applicable rule section.

{| class="wikitable" 
|-
! colspan="3" style="text-align:center; font-weight:bold;" | Operating Frequency / Maximum transmission power
|-
| rowspan="3" style="font-weight:bold;" | WCDMA
| B1
| 1920-1980, 2110-2170 MHz, 25 dBm
|-
| B5<sup>1</sup>
| 824-849, 869-894 MHz, 25 dBm
|-
| B8
| 880-915, 925-960 MHz, 25 dBm
|-
| rowspan="7" style="font-weight:bold;" | LTE-FDD
| B1
| 1920-1980, 2110-2170 MHz, 25 dBm
|-
| B3
| 1710-1785, 1805-1880 MHz, 25 dBm
|-
| B5<sup>1</sup>
| 824-849, 869-894 MHz, 25 dBm
|-
| B7
| 2500-2570, 2620-2690 MHz, 25 dBm
|-
| B8
| 880-915, 925-960 MHz, 25 dBm
|-
| B20
| 832-862, 791-821 MHz, 25 dBm
|-
| B28
| 703-748, 758-803 MHz, 25 dBm
|-
| rowspan="5" style="font-weight:bold;" | LTE-TDD
| B38
| 2570-2620 MHz, 28 dBm
|-
| B40
| 2300-2400 MHz, 28 dBm
|-
| B41<sup>2</sup>
| 2496-2690 MHz, 28 dBm
|-
| B42<sup>2</sup>
| 3400-3600 MHz, 28 dBm
|-
| B43<sup>2</sup>
| 3600-3800 MHz, 28 dBm
|-
| rowspan="12" style="font-weight:bold;" | 5G NR (SA, NSA)
| n1
| 1920-1680, 2110-2170 MHz, 25 dBm
|-
| n3
| 1710-1785, 1805-1880 MHz, 25 dBm
|-
| n5<sup>1</sup>
| 824-849, 869-894 MHz, 25 dBm
|-
| n7
| 2500-2570, 2620-2690 MHz, 25 dBm
|-
| n8
| 880-915, 925-960 MHz, 25 dBm
|-
| n20
| 832-862, 791-821 MHz, 25 dBm
|-
| n28
| 703-748, 758-803 MHz, 25 dBm
|-
| n38
| 2570-2620 MHz, 25 dBm
|-
| n40
| 2300-2400 MHz, 25 dBm
|-
| n41
| 2496-2690 MHz, 28 dBm
|-
| n77
| 3300-4200 MHz, 28 dBm
|-
| n78
| 3300-3800 MHz, 28 dBm
|-
| style="font-weight:bold;" | Wi-Fi 2.4 GHz
| colspan="2" | 2412-2472 MHz, 20 dBm
|-
| rowspan="4" style="font-weight:bold;" | Wi-Fi 5 GHz
| UNII-1 Band 1
| 5180-5240 MHz, 23 dBm
|-
| UNII-2A Band 2
| 5260-5320 MHz, 30 dBm
|-
| UNII-2C Band 3
| 5500-5700 MHz, 30 dBm
|-
| UNII-3 Band 4
| 5745-5825 MHz, 13.98 dBm
|}

<small><sup>1</sup> – Not supported in Europe region.</small>

<small><sup>2</sup> – Not supported in Europe and Oceania regions.</small>

[[Image:Restrictions_LOGO.png|50px]] In all EU member states, operation of 5150-5350 MHz is restricted to indoor use only.


=Product Safety and Use=

== Operating conditions ==

* Operating temperature: -40° to +75° Celsius
* Humidity should be in the range of 10% to 90% (non-condensing). Only use the device in dry environments.
* Out of direct sunlight
* Away from heat source, corrosive substances, salts, and flammable gases

'''Attention:''' operation outside the permissible range can considerably shorten the service life of the device.

== Faulty and damaged products ==

* Do not attempt to disassemble the device or its accessories.
* Only qualified personnel must service or repair the device or its accessories.
* If your device or its accessories have been submerged in water punctured or subjected to a severe fall, do not use until they have been checked at an authorized service center.

== Electrical safety ==

* Only use approved accessories.
* Do not connect with incompatible products or accessories.
* It is recommended to ground devices with grounding terminals before connecting them to power. Failure to ground appropriately might result in a shock hazard. The cross-sectional area of the protective grounding conductor should be at least 1mm2.

== Product handling ==

* You alone are responsible for how you use your device and any consequences related to its use.
* Use of your device is subject to safety measures designed to protect users and their environment.
* Always treat your device and its accessories with care and keep it in a clean and dust-free place.
* Do not expose your device or its accessories to open flames or lit tobacco products, liquid, moisture, or high humidity.
* Do not drop, throw or try to bend your device or its accessories.
* Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its accessories.
* Do not paint your device or its accessories.
* Do not attempt to disassemble your device (exemptions for devices that require disassembly for SIM insertion) or its accessories: it does not contain any user-serviceable parts. For safety reasons, the equipment should be opened only by qualified personnel.
* Make sure to use ESD personal protective equipment while the equipment is serviced.
* Do not use your device in an enclosed environment where heat dissipation is poor.
* Prolonged use in such space may cause excessive heat and raise ambient temperature, which will lead to the automatic shutdown of your device or the disconnection of the mobile network connection for your safety. To use your device again after such a shutdown, cool it in a well-ventilated place before turning it on.
* Please check all national laws and local regulations for the disposal of electronic products.
* Do not operate the device where ventilation is restricted.
* Do not use or install this product near water to avoid fire or shock hazards.
* Avoid exposing the equipment to rain or damp areas.
* Arrange power and Ethernet cables so that they are not likely to be stepped on or have items placed on them.
* Ensure that the voltage and the rated current of the power source match the device’s requirements. Do not connect the device to an inappropriate power source.
* During a thunderstorm, no operations should be carried out on the device and cables.
* The unit must be powered off where blasting is in progress and explosive atmospheres are present or near medical life support equipment.
* Do not leave your device and its accessories within reach of small children or allow them to play with it. They could hurt themselves or others and could accidentally damage the device. Your device contains small parts with sharp edges that may cause an injury choking hazard.
* Like any wireless device, this device operates using radio signals, which cannot guarantee connection in all conditions. Therefore, you must never rely solely on any wireless device for emergency communications or otherwise use the device in situations where the interruption of data connectivity could lead to death, personal injury, property damage, data, or other loss.
* The device may become warm during regular use.

=Quick Start Guide=

== Front view ==

<br>
[[File:Front view ATRM50.png|center|1100 px|link=Special:FilePath/Front view ATRM50.png]]

== Back view ==

<br>
[[File:Back view ATRM50.png|center|1100 px|link=Special:FilePath/Back view ATRM50.png]]

== Connectors ==

<br>
'''POWER SOCKET PINOUT'''

<table>
    <tr>
        <td style="vertical-align: top; margin: 10px; padding-bottom: 25px;">[[File:Connectors ATRM50.png|left|800 px]]</td>
    </tr>
</table>

== Mounting instruction ==

====NOTE====
* The tools and fasteners required for mounting the ATRM50 device depend on the surface material and the type of fasteners selected  Ensure that the fasteners are appropriate in size and type for the installation surface and are compatible with the device.
* When installing the device, make sure to allow sufficient space for proper cable and antenna installation. Refer to the mounting dimensions drawing below for guidance. For a clearer view, please use the file: [https://wiki.teltonika-networks.com/images/6/6e/ATRM50_spatial_measurement_v1.0.pdf ATRM50_Spatial_Measurements.pdf].
{| class="wikitable"
|+ ATRM50 Spatial Drawings
|-
| [[File:ATRM50 Mounting Space 1.png|center|200px|link=Special:FilePath/ATRM50 Mounting Space 1.png]]|| [[File:ATRM50 Mounting Space 2.png|center|200px|link=Special:FilePath/ATRM50 Mounting Space 2.png]]
|-
| [[File:ATRM50 Mounting Space 3.png|center|200px|link=Special:FilePath/ATRM50 Mounting Space 3.png]]|| [[File:ATRM50 Mounting Space 4.png|center|200px|link=Special:FilePath/ATRM50 Mounting Space 4.png]]
|}
=== Device mounting with pan head tapping screws ===
<table>
    <tr>
       <td style="vertical-align: top; margin: 10px; padding-bottom: 0px; padding-right: 50px; padding-left: 50px;"> 1. The device should be placed on a flat surface (vertically or horizontally). [[File:ATRM50_Mounting_1.png|center|500px|link=Special:FilePath/ATRM50_Mounting_1.png]]</td>
      <td style="vertical-align: top; margin: 0px; padding-right: 50px; padding-left: 50px; padding-bottom: 5px;"> 2. Fasten the device to the surface by tightening the 4 appropriate screws. The diameter of the holes are Ø 4.50 mm, or about 0.17 inches.[[File:ATRM50_Mounting_pan head_2.png|center|400px|link=Special:FilePath/ATRM50_Mounting_pan head_2.png]]</td>
    </tr>

    <tr>
        <td style="vertical-align: top; margin: 10px; padding-bottom: 25px; padding-right: 50px; padding-left: 50px;"> 3. A visual representation on a fully fastened device (side view).
[[File:ATRM50_Mounting_pan head_3_1.png|center|400px|link=Special:FilePath/ATRM50_Mounting_pan head_3.png]]</td>
    </tr>
</table>

=== Device mounting with M4 bolts ===
<table>
    <tr>
       <td style="vertical-align: top; margin: 10px; padding-bottom: 0px; padding-right: 50px; padding-left: 50px;"> 1. The device should be placed on a flat surface (vertically or horizontally). [[File:ATRM50_Mounting_1.png|center|500px|link=Special:FilePath/ATRM50_Mounting_1.png]]</td>
      <td style="vertical-align: top; margin: 0px; padding-right: 50px; padding-left: 50px; padding-bottom: 5px;"> 2. Fasten the device to the surface by tightening  2 bolts alongside with 4 washers and 2 nuts, fitting for the type of surface. The dimensions of the slotted holes are 4.50 mm by 5.00 mm, or approximately 0.19 inches by 0.17 inches[[File:ATRM50_Mounting_M4 Bolts_2.png|center|400px|link=Special:FilePath/ATRM50_Mounting_M4 Bolts_2.png]]</td>
    </tr>

    <tr>
        <td style="vertical-align: top; margin: 10px; padding-bottom: 25px; padding-right: 50px; padding-left: 50px;"> 3. A visual representation on a fully fastened device (side view).
[[File:ATRM50_Mounting_M4 Bolts_3.png|center|400px|link=Special:FilePath/ATRM50_Mounting_M4 Bolts_3.png]]</td>
    </tr>
</table>


{{Template:Rut_esim_desc_template_full_support
<!------------------------DEVICE----------------------->
| name         = ATRM50
}}

{{Template: Configure_your_computer_LAN_Windows
<!------------------------DEVICE----------------------->
| name         = ATRM50 
}}


{{Template: Configure_your_computer_WiFi_Windows
<!------------------------DEVICE----------------------->
| name         = ATRM50
}}

== Login to device ==

<br>
<table>
    <tr>
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; margin: 10px; padding-bottom: 25px;">1. To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.<br><br>2. When prompted for authentication enter the username admin and enter the password located on the device information label/engraving. </td>
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; width: 680px; margin: 10px; padding-bottom: 25px;">[[File:900px-Login to device step 1.png|right]]</td>
    </tr>
    <tr>
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; padding-top: 25px;">3. After logging in, you must set a new password for security reasons. You will not be able to interact with the router’s WebUI until the default password is changed. The new password must consist of a minimum of '''8 characters'''. Requirements: one uppercase letter, one lowercase letter, and one digit.<br><br>4. Next, the Configuration Wizard will start to help you set up some of the router's main operational parameters.<br><br>5. Finally, let's verify the Mobile signal strength. Go to the '''Status — Network''' page and pay attention to the '''Signal Strength''' indication. 


To achieve the best signal conditions and maximize cellular performance, try adjusting the antennas or changing the location of your device. You can find information on signal strength recommendations here.
</td>
        <td style="border-bottom: 0px solid #e8e8e8; vertical-align: top; padding-bottom: 25px; padding-top: 25px;">[[File:Login to device step v1.png|right]]</td>
    </tr>
</table>

== SIM card recommendations ==

* Before installing the SIM cards, please apply a thin layer of dielectric grease to the SIM card contacts for devices used in environments with '''high-vibration levels'''. This will help avoid SIM cards losing touch with the SIM slot and prevent unexpected failures.
* Industrial Grade SIM cards are recommended for devices requiring a long lifespan used in environments with '''extreme temperatures''', '''corrosive''' or '''extra humid climates''', or hard-to-reach locations.

[[Category: ATRM50]]