8,949
edits
Changes
Template:Networking tswos manual ports (view source)
Revision as of 13:20, 13 October 2023
, 13:20, 13 October 2023Created page with "{{Template: Networking_rutos_manual_fw_disclosure | fw_version ={{Template: Networking_rutos_manual_latest_fw | series = {{{series}}} | name = {{{name}}} }} }} __TOC__ ==..."
{{Template: Networking_rutos_manual_fw_disclosure
| fw_version ={{Template: Networking_rutos_manual_latest_fw
| series = {{{series}}}
| name = {{{name}}}
}}
}}
__TOC__
==Summary==
The <b>Ports</b> page provides information related to the status of the device's physical ports, as well as the ability to edit port settings, security, loopback detection.
==General==
In this section you can enable <b>Jubo frames</b> and <b>LLDP frame filter</b> services.
[[File:Networking_tswos_manual_ports_general.png|border|class=tlt-border]]
<table class="nd-mantable">
<tr>
<th>Field</th>
<th>Value</th>
<th>Description</th>
</tr>
<tr>
<td>Jumbo frames</td>
<td>off {{!}} on; default: <b>on</b></td>
<td>Allow ethernet frame with a payload greater than the standard maximum transmission unit (MTU) of 1500 bytes. This may improve network performance by making data transmissions more efficient.</td>
</tr>
<tr>
<td>LLDP frame filter</td>
<td><span style="color:red">off</span> {{!}} on; default: <b>off</b></td>
<td>Enable to stop the forwarding of LLDP frames.</td>
</tr>
</table>
==Port Settings==
This section displays information about the status of the device's ports with the ability to configure port settings.
===Port Settings===
----
The figure below is an example of the '''All Ports''' window, color indicates port speed and status:
[[File:Networking_tswos_manual_ports_ports_settings_port_settings.png|border|class=tlt-border]]
To change port settings select port and press `edit (number of ports) ports` button:
[[File:Networking_tswos_manual_ports_ports_settings_port_settings_edit.png|border|class=tlt-border]]
You will be redirected to `Port settings`. From here you can enable/disable ports or change settings:
[[File:Networking_tswos_manual_ports_ports_settings_port_settings_settings.png|border|class=tlt-border]]
<table class="nd-mantable">
<tr>
<th>Field</th>
<th>Value</th>
<th>Description</th>
</tr>
<tr>
<td>Enable</td>
<td>off {{!}} on; default: <b>on</b></td>
<td>Toggle port on or off.</td>
</tr>
<tr>
<td>EEE</td>
<td>off {{!}} on; default: <b>on</b></td>
<td>Enable Energy-Efficient Ethernet.</td>
</tr>
<tr>
<td>Isolate port</td>
<td>off {{!}} on; default: <b>off</b></td>
<td>When enabled port will be isolated from other isolated ports. Traffic between isolated ports will droped. Traffic between isolated and normal ports will be sent as normal.</td>
</tr>
<tr>
<td>Link speed</td>
<td>Auto {{!}} <span style="color: red;">10Mbps (E)</span> {{!}} <span style="color: red;">100Mbps (FE)</span> {{!}} <span style="color: red;">1000Mbps (GbE)</span>; default: <b>Auto</b></td>
<td>A measure of how fast ports are able to transmit and receive data.</td>
</tr>
<tr>
<td><span style="color: red;">Duplex</span></td>
<td>Full {{!}} Half; default: <b></b></td>
<td>Advertises preferred duplex mode and speed for negotiation with other devices.</td>
</tr>{{#ifeq: {{{poe}}}|1|
<tr>
<td>PoE</td>
<td>off {{!}} on; default: <b>on</b></td>
<td> Enable Power over Ethernet. </td>
</tr>|}}
</table>
===Port Status===
----
This section displays port status information. There is also an option to select, enable ports, enable/disable PoE, EEE and Isolation options:
[[File:Networking_tswos_manual_ports_ports_settings_port_status_{{{poe}}}.png|border|class=tlt-border]]
<table class="nd-othertables_2">
<tr>
<th width="250">Field Name</th>
<th width="900">Description</th>
</tr>
<tr>
<td>Port</td>
<td>Port ID.</td>
</tr>
<tr>
<td>Enabled</td>
<td>Enable/Disable port.</td>
</tr>
<tr>
<td>Status</td>
<td>Port status.</td>
</tr>
<tr>
<td>Speed</td>
<td>Port link speed.
<li>Possible speeds:</li>
<li>GbE: 1000Mbps</li>
<li>FE: 100Mbps</li>
<li>E: 10Mbps</li>
</td>
</tr>{{#ifeq: {{{poe}}}|1|
<tr>
<td>PoE</td>
<td>Enable/Disable Power over Ethernet. </td>
</tr>|}}
<tr>
<td>PoE (W)</td>
<td>PoE port power usage in watts.</td>
</tr>
<tr>
<td>EEE</td>
<td>Enable/Disable Energy-Efficient Ethernet.</td>
</tr>
<tr>
<td>Isolation</td>
<td>When enabled port will be isolated from other isolated ports. Traffic between isolated ports will be droped. Traffic between isolated and normal ports will be sent as normal.</td>
</tr>
<tr>
<td>TX sum</td>
<td>Total upload.</td>
</tr>
<tr>
<td>RX sum</td>
<td>Total download.</td>
</tr>
<tr>
<td>TX rate</td>
<td>Upload speed.</td>
</tr>
<tr>
<td>RX rate</td>
<td>Download speed.</td>
</tr>
</table>
==Port Mirroring==
Port Mirroring is a service that mirrors incoming and outgoing packets on one Ethernet port (Source Port) to another (Monitoring Port).
To change port mirroring settings select port and press `Edit` button:
[[File:Networking_tswos_manual_ports_port_mirroring_edit.png|border|class=tlt-border]]
You will be redirected to `Port mirroring settings`. From here you can select ingress and egress ports:
[[File:Networking_tswos_manual_ports_port_mirroring_configuration.png|border|class=tlt-border]]
<table class="nd-mantable">
<tr>
<th>Field</th>
<th>Value</th>
<th>Description</th>
</tr>
<tr>
<td>Enable</td>
<td>off {{!}} on; default: <b>off</b></td>
<td>The port which will mirror the packets.</td>
</tr>
<tr>
<td>Ingress mirroring port list</td>
<td>port; default: <b>none</b></td>
<td>Specify which port incoming traffic is mirrored.</td>
</tr>
<tr>
<td>Egress mirroring port list</td>
<td>port; default: <b>none</b></td>
<td>Specify which port outcoming traffic is mirrored.</td>
</tr>
</table>
==Loopback Detection==
===Loopback Detection===
----
A port-based loopback detection service that using its own distinctive packets, seeks to identify and break a network loop by shutting down troublesome ports.
[[File:Networking_tswos_manual_ports_loopback_detection.png|border|class=tlt-border]]
<table class="nd-mantable">
<tr>
<th>Field</th>
<th>Value</th>
<th>Description</th>
</tr>
<tr>
<td>Enable</td>
<td>off {{!}} on; default: <b>off</b></td>
<td>Enable loopback detection.</td>
</tr>
<tr>
<td>Broadcast interval</td>
<td>integer [1..10000]; default: <b>none</b></td>
<td>Send detection packets in an given interval from 1 to 10000 seconds.</td>
</tr>
<tr>
<td>Auto-recovery interval</td>
<td>integer [60..10000]; default: <b>none</b></td>
<td>Restores disabled ports in an given interval from 60 to 10000 seconds.</td>
</tr>
</table>
===Port Tracking===
----
Tracks specific port status. <b>Notes:</b>
<li><b>STP:</b> STP must be disabled in Network -> Spanning Tree and loopback detection must be enabled for the service to function.</li>
<li><b>Port unblocking:</b> When a loop occurs before a broadcast, it won't be recognized until the broadcast transmits its own packets, since the service only listens for packets with its own particular protocol.</li>
[[Category:{{{name}}} Network section]]
| fw_version ={{Template: Networking_rutos_manual_latest_fw
| series = {{{series}}}
| name = {{{name}}}
}}
}}
__TOC__
==Summary==
The <b>Ports</b> page provides information related to the status of the device's physical ports, as well as the ability to edit port settings, security, loopback detection.
==General==
In this section you can enable <b>Jubo frames</b> and <b>LLDP frame filter</b> services.
[[File:Networking_tswos_manual_ports_general.png|border|class=tlt-border]]
<table class="nd-mantable">
<tr>
<th>Field</th>
<th>Value</th>
<th>Description</th>
</tr>
<tr>
<td>Jumbo frames</td>
<td>off {{!}} on; default: <b>on</b></td>
<td>Allow ethernet frame with a payload greater than the standard maximum transmission unit (MTU) of 1500 bytes. This may improve network performance by making data transmissions more efficient.</td>
</tr>
<tr>
<td>LLDP frame filter</td>
<td><span style="color:red">off</span> {{!}} on; default: <b>off</b></td>
<td>Enable to stop the forwarding of LLDP frames.</td>
</tr>
</table>
==Port Settings==
This section displays information about the status of the device's ports with the ability to configure port settings.
===Port Settings===
----
The figure below is an example of the '''All Ports''' window, color indicates port speed and status:
[[File:Networking_tswos_manual_ports_ports_settings_port_settings.png|border|class=tlt-border]]
To change port settings select port and press `edit (number of ports) ports` button:
[[File:Networking_tswos_manual_ports_ports_settings_port_settings_edit.png|border|class=tlt-border]]
You will be redirected to `Port settings`. From here you can enable/disable ports or change settings:
[[File:Networking_tswos_manual_ports_ports_settings_port_settings_settings.png|border|class=tlt-border]]
<table class="nd-mantable">
<tr>
<th>Field</th>
<th>Value</th>
<th>Description</th>
</tr>
<tr>
<td>Enable</td>
<td>off {{!}} on; default: <b>on</b></td>
<td>Toggle port on or off.</td>
</tr>
<tr>
<td>EEE</td>
<td>off {{!}} on; default: <b>on</b></td>
<td>Enable Energy-Efficient Ethernet.</td>
</tr>
<tr>
<td>Isolate port</td>
<td>off {{!}} on; default: <b>off</b></td>
<td>When enabled port will be isolated from other isolated ports. Traffic between isolated ports will droped. Traffic between isolated and normal ports will be sent as normal.</td>
</tr>
<tr>
<td>Link speed</td>
<td>Auto {{!}} <span style="color: red;">10Mbps (E)</span> {{!}} <span style="color: red;">100Mbps (FE)</span> {{!}} <span style="color: red;">1000Mbps (GbE)</span>; default: <b>Auto</b></td>
<td>A measure of how fast ports are able to transmit and receive data.</td>
</tr>
<tr>
<td><span style="color: red;">Duplex</span></td>
<td>Full {{!}} Half; default: <b></b></td>
<td>Advertises preferred duplex mode and speed for negotiation with other devices.</td>
</tr>{{#ifeq: {{{poe}}}|1|
<tr>
<td>PoE</td>
<td>off {{!}} on; default: <b>on</b></td>
<td> Enable Power over Ethernet. </td>
</tr>|}}
</table>
===Port Status===
----
This section displays port status information. There is also an option to select, enable ports, enable/disable PoE, EEE and Isolation options:
[[File:Networking_tswos_manual_ports_ports_settings_port_status_{{{poe}}}.png|border|class=tlt-border]]
<table class="nd-othertables_2">
<tr>
<th width="250">Field Name</th>
<th width="900">Description</th>
</tr>
<tr>
<td>Port</td>
<td>Port ID.</td>
</tr>
<tr>
<td>Enabled</td>
<td>Enable/Disable port.</td>
</tr>
<tr>
<td>Status</td>
<td>Port status.</td>
</tr>
<tr>
<td>Speed</td>
<td>Port link speed.
<li>Possible speeds:</li>
<li>GbE: 1000Mbps</li>
<li>FE: 100Mbps</li>
<li>E: 10Mbps</li>
</td>
</tr>{{#ifeq: {{{poe}}}|1|
<tr>
<td>PoE</td>
<td>Enable/Disable Power over Ethernet. </td>
</tr>|}}
<tr>
<td>PoE (W)</td>
<td>PoE port power usage in watts.</td>
</tr>
<tr>
<td>EEE</td>
<td>Enable/Disable Energy-Efficient Ethernet.</td>
</tr>
<tr>
<td>Isolation</td>
<td>When enabled port will be isolated from other isolated ports. Traffic between isolated ports will be droped. Traffic between isolated and normal ports will be sent as normal.</td>
</tr>
<tr>
<td>TX sum</td>
<td>Total upload.</td>
</tr>
<tr>
<td>RX sum</td>
<td>Total download.</td>
</tr>
<tr>
<td>TX rate</td>
<td>Upload speed.</td>
</tr>
<tr>
<td>RX rate</td>
<td>Download speed.</td>
</tr>
</table>
==Port Mirroring==
Port Mirroring is a service that mirrors incoming and outgoing packets on one Ethernet port (Source Port) to another (Monitoring Port).
To change port mirroring settings select port and press `Edit` button:
[[File:Networking_tswos_manual_ports_port_mirroring_edit.png|border|class=tlt-border]]
You will be redirected to `Port mirroring settings`. From here you can select ingress and egress ports:
[[File:Networking_tswos_manual_ports_port_mirroring_configuration.png|border|class=tlt-border]]
<table class="nd-mantable">
<tr>
<th>Field</th>
<th>Value</th>
<th>Description</th>
</tr>
<tr>
<td>Enable</td>
<td>off {{!}} on; default: <b>off</b></td>
<td>The port which will mirror the packets.</td>
</tr>
<tr>
<td>Ingress mirroring port list</td>
<td>port; default: <b>none</b></td>
<td>Specify which port incoming traffic is mirrored.</td>
</tr>
<tr>
<td>Egress mirroring port list</td>
<td>port; default: <b>none</b></td>
<td>Specify which port outcoming traffic is mirrored.</td>
</tr>
</table>
==Loopback Detection==
===Loopback Detection===
----
A port-based loopback detection service that using its own distinctive packets, seeks to identify and break a network loop by shutting down troublesome ports.
[[File:Networking_tswos_manual_ports_loopback_detection.png|border|class=tlt-border]]
<table class="nd-mantable">
<tr>
<th>Field</th>
<th>Value</th>
<th>Description</th>
</tr>
<tr>
<td>Enable</td>
<td>off {{!}} on; default: <b>off</b></td>
<td>Enable loopback detection.</td>
</tr>
<tr>
<td>Broadcast interval</td>
<td>integer [1..10000]; default: <b>none</b></td>
<td>Send detection packets in an given interval from 1 to 10000 seconds.</td>
</tr>
<tr>
<td>Auto-recovery interval</td>
<td>integer [60..10000]; default: <b>none</b></td>
<td>Restores disabled ports in an given interval from 60 to 10000 seconds.</td>
</tr>
</table>
===Port Tracking===
----
Tracks specific port status. <b>Notes:</b>
<li><b>STP:</b> STP must be disabled in Network -> Spanning Tree and loopback detection must be enabled for the service to function.</li>
<li><b>Port unblocking:</b> When a loop occurs before a broadcast, it won't be recognized until the broadcast transmits its own packets, since the service only listens for packets with its own particular protocol.</li>
[[Category:{{{name}}} Network section]]