Jump to content
  • EN

RUT230 Wireless: Difference between revisions

RUT230 Wireless (view source)

Revision as of 07:49, 1 March 2019

105 bytes removed ,  1 March 2019
no edit summary
VisualWikitext
No edit summary
Line 47: Line 47:
     <tr>
     <tr>
       <td>Mode</td>
       <td>Mode</td>
       <td>Auto {{!}} 802.11b {{!}} 802.11g {{!}} 802.11g+n; Default: '''802.11g+n'''</td>
       <td>Auto | 802.11b | 802.11g | 802.11g+n; Default: '''802.11g+n'''</td>
       <td>Wireless protocol used. Different modes provide different wireless standard support which directly impacts the radio's throughput performance</td>
       <td>Wireless protocol used. Different modes provide different wireless standard support which directly impacts the radio's throughput performance</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>HT mode</td>
       <td>HT mode</td>
       <td>20 MHz {{!}} 40 MHz 2nd channel above; Default: '''20 MHz'''</td>
       <td>20 MHz | 40 MHz 2nd channel above; Default: '''20 MHz'''</td>
       <td>HT (High Throughput) mode allows you to specify channel width. 40 MHz bandwidth provides better performance but it overlaps 4 adjacent channels on each side, therefore, it might overlap with many other Access Points working in those channels. If that is the case, the router will switch back to 20 MHz mode automatically to reduce interference. 40 MHz is only available if the selected channel is not '''Auto'''</td>
       <td>HT (High Throughput) mode allows you to specify channel width. 40 MHz bandwidth provides better performance but it overlaps 4 adjacent channels on each side, therefore, it might overlap with many other Access Points working in those channels. If that is the case, the router will switch back to 20 MHz mode automatically to reduce interference. 40 MHz is only available if the selected channel is not '''Auto'''</td>
     </tr>
     </tr>
Line 62: Line 62:
     <tr>
     <tr>
     <td>Transmit power</td>
     <td>Transmit power</td>
         <td>100 % {{!}} 80 % {{!}} 60 % {{!}} 40 % {{!}} 20 %; Default: '''100 %'''</td>
         <td>100 % | 80 % | 60 % | 40 % | 20 %; Default: '''100 %'''</td>
         <td>WiFi signal power. Use lower power to reduce the router's CPU usage</td>
         <td>WiFi signal power. Use lower power to reduce the router's CPU usage</td>
     </tr>
     </tr>
Line 103: Line 103:
     <tr>
     <tr>
       <td>Encryption*</td>
       <td>Encryption*</td>
       <td>No encryption {{!}} WEP Open System {{!}} WEP shared key; Default: '''No encryption'''</td>
       <td>No encryption | WEP Open System | WEP shared key; Default: '''No encryption'''</td>
       <td>The type of WiFi encryption used. Configurations for both '''WEP Open System''' and '''WEP shared key''' are identical</td>
       <td>The type of WiFi encryption used. Configurations for both '''WEP Open System''' and '''WEP shared key''' are identical</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Used key slot</td>
       <td>Used key slot</td>
       <td>Key #1 {{!}} Key #2 {{!}} Key #3 {{!}} Key #4; Default: '''Key #1'''</td>
       <td>Key #1 | Key #2 | Key #3 | Key #4; Default: '''Key #1'''</td>
       <td>Specifies which key is used for authentication</td>
       <td>Specifies which key is used for authentication</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Key #1 {{!}} Key #2 {{!}} Key #3 {{!}} Key #4</td>
     <td>Key #1 | Key #2 | Key #3 | Key #4</td>
         <td>string; Default: " "</td>
         <td>string; Default: " "</td>
         <td>A 10 symbol custom key used for authentication </td>
         <td>A 10 symbol custom key used for authentication </td>
Line 130: Line 130:
     <tr>
     <tr>
       <td>Encryption*</td>
       <td>Encryption*</td>
       <td>No encryption {{!}} WPA-PSK {{!}} WPA2-PSK {{!}} WPA-PSK/WPA2-PSK mixed mode; Default: '''No encryption'''</td>
       <td>No encryption | WPA-PSK | WPA2-PSK | WPA-PSK/WPA2-PSK mixed mode; Default: '''No encryption'''</td>
       <td>The type of WiFi encryption used. Configurations for both '''WEP Open System''' and '''WEP shared key''' are identical</td>
       <td>The type of WiFi encryption used. Configurations for both '''WEP Open System''' and '''WEP shared key''' are identical</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Cipher</td>
       <td>Cipher</td>
       <td>Auto {{!}} Force CCMP (AES) {{!}} Force TKIP {{!}} Force TKIP and CCMP (AES); Default: '''Auto'''</td>
       <td>Auto | Force CCMP (AES) | Force TKIP | Force TKIP and CCMP (AES); Default: '''Auto'''</td>
       <td>An algorithm for performing encryption or decryption</td>
       <td>An algorithm for performing encryption or decryption</td>
     </tr>
     </tr>
Line 160: Line 160:
     <tr>
     <tr>
       <td>Encryption*</td>
       <td>Encryption*</td>
       <td>No encryption {{!}} WPA-PSK {{!}} WPA2-PSK {{!}} WPA-PSK/WPA2-PSK mixed mode; Default: '''No encryption'''</td>
       <td>No encryption | WPA-PSK | WPA2-PSK | WPA-PSK/WPA2-PSK mixed mode; Default: '''No encryption'''</td>
       <td>The type of WiFi encryption used. Configurations for both '''WEP Open System''' and '''WEP shared key''' are identical</td>
       <td>The type of WiFi encryption used. Configurations for both '''WEP Open System''' and '''WEP shared key''' are identical</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Cipher</td>
       <td>Cipher</td>
       <td>Auto {{!}} Force CCMP (AES) {{!}} Force TKIP {{!}} Force TKIP and CCMP (AES); Default: '''Auto'''</td>
       <td>Auto | Force CCMP (AES) | Force TKIP | Force TKIP and CCMP (AES); Default: '''Auto'''</td>
       <td>An algorithm for performing encryption or decryption</td>
       <td>An algorithm for performing encryption or decryption</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Radius Server IP</td>
     <td>Radius Server IP</td>
         <td>host {{!}} ip; Default: " "</td>
         <td>host | ip; Default: " "</td>
         <td>RADIUS server's IP address or host name</td>
         <td>RADIUS server's IP address or host name</td>
     </tr>
     </tr>
Line 199: Line 199:
     <tr>
     <tr>
       <td>MAC address filter</td>
       <td>MAC address filter</td>
       <td>Disable {{!}} Allow listed only {{!}} Allow all except listed; Default: '''Disable'''</td>
       <td>Disable | Allow listed only | Allow all except listed; Default: '''Disable'''</td>
       <td>'''Allow listed only''' – only allows devices with MAC addresses specified in the MAC list to connect to your WiFi network
       <td>'''Allow listed only''' – only allows devices with MAC addresses specified in the MAC list to connect to your WiFi network
'''Allow all except listed''' -  blocks devices with MAC addresses specified in the MAC list from connecting to your WiFi network</td>
'''Allow all except listed''' -  blocks devices with MAC addresses specified in the MAC list from connecting to your WiFi network</td>
Line 227: Line 227:
     <tr>
     <tr>
       <td>Separate clients</td>
       <td>Separate clients</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Prevents WiFi clients from communicating with each other on the same subnet</td>
       <td>Prevents WiFi clients from communicating with each other on the same subnet</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Increase TTL packet size </td>
       <td>Increase TTL packet size </td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Increase TTL packet size for incoming packets</td>
       <td>Increase TTL packet size for incoming packets</td>
     </tr>
     </tr>
Line 256: Line 256:


[[Image:Network wireless station step3.PNG]]
[[Image:Network wireless station step3.PNG]]
[[Category:RUT230 WebUI]]
Retrieved from "https://wiki.teltonika-networks.com/view/Special:MobileDiff/29112"