Line 21: |
Line 21: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles QoS functionality ON or OFF</td> | | <td>Toggles QoS functionality ON or OFF</td> |
| </tr> | | </tr> |
Line 29: |
Line 29: |
| <tr> | | <tr> |
| <td>Interface</td> | | <td>Interface</td> |
− | <td>WAN {{!}} LAN {{!}} PPP; Default: '''WAN'''</td> | + | <td>WAN | LAN | PPP; Default: '''WAN'''</td> |
| <td>Interface that the rule applies to</td> | | <td>Interface that the rule applies to</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles the rule ON or OFF</td> | | <td>Toggles the rule ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Calculate overhead</td> | | <td>Calculate overhead</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Decreases upload and download ratio to prevent link saturation</td> | | <td>Decreases upload and download ratio to prevent link saturation</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Half-duplex</td> | | <td>Half-duplex</td> |
− | <td>es {{!}} no; Default: '''no'''</td> | + | <td>es | no; Default: '''no'''</td> |
| <td>Enables data transmission in both directions on a single carrier</td> | | <td>Enables data transmission in both directions on a single carrier</td> |
| </tr> | | </tr> |
Line 71: |
Line 71: |
| <tr> | | <tr> |
| <td>Target</td> | | <td>Target</td> |
− | <td>Priority {{!}} Express {{!}} Normal {{!}} Low; Default: '''WAN'''</td> | + | <td>Priority | Express | Normal | Low; Default: '''WAN'''</td> |
| <td>Target for which the rule will be applied</td> | | <td>Target for which the rule will be applied</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Source host</td> | | <td>Source host</td> |
− | <td>All {{!}} ip; Default: '''All'''</td> | + | <td>All | ip; Default: '''All'''</td> |
| <td>Host from which data will be transmitted</td> | | <td>Host from which data will be transmitted</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Destination host</td> | | <td>Destination host</td> |
− | <td>All {{!}} ip; Default: '''All'''</td> | + | <td>All | ip; Default: '''All'''</td> |
| <td>Host to which data will be transmitted</td> | | <td>Host to which data will be transmitted</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Protocol</td> | | <td>Protocol</td> |
− | <td>All {{!}} TCP {{!}} UDP {{!}} ICMP {{!}} -- custom --; Default: '''All'''</td> | + | <td>All | TCP | UDP | ICMP | -- custom --; Default: '''All'''</td> |
| <td>Data transmission protocol</td> | | <td>Data transmission protocol</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Ports</td> | | <td>Ports</td> |
− | <td>All {{!}} integer [0..65535]; Default: '''22,53'''</td> | + | <td>All | integer [0..65535]; Default: '''22,53'''</td> |
| <td>Port(s) that will be used for transmission. You can enter multiple ports by separating them by commas (',')</td> | | <td>Port(s) that will be used for transmission. You can enter multiple ports by separating them by commas (',')</td> |
| </tr> | | </tr> |
Line 100: |
Line 100: |
| </tr> | | </tr> |
| </table> | | </table> |
| + | |
| + | [[Category:RUT230 WebUI]] |