Line 8: |
Line 8: |
| | | |
| * One RUTxxx router of any type | | * One RUTxxx router of any type |
− | * One Cisco router of any type | + | * One Cisco router (this configuration example was created using Cisco RV340W) |
| * At least one router must have a Public Static or Public Dynamic IP address | | * At least one router must have a Public Static or Public Dynamic IP address |
| * At least one end device (PC, Laptop, Tablet, Smartphone) to configure the routers | | * At least one end device (PC, Laptop, Tablet, Smartphone) to configure the routers |
Line 15: |
Line 15: |
| ==Configuration scheme== | | ==Configuration scheme== |
| | | |
− | [[File:Networking_rutxxx_configuration_example_ipsec_topology_v1.png|border|class=tlt-border|1100x1100px]] | + | [[File:Networking_rutxxx_configuration_example_ipsec_topology_v2.png|border|class=tlt-border|1100x1100px]] |
| | | |
| ==RUT configuration== | | ==RUT configuration== |
Line 49: |
Line 49: |
| # Write '''Pre-shared key''' (a shared password used for authentication between the peers. The value of this field must match on both instances). | | # Write '''Pre-shared key''' (a shared password used for authentication between the peers. The value of this field must match on both instances). |
| # Add '''Secret's ID selector''' (Cisco LAN IP). | | # Add '''Secret's ID selector''' (Cisco LAN IP). |
− | # Press '''Save''' | + | # Press '''Save'''. |
| | | |
| ==Cisco configuration== | | ==Cisco configuration== |
Line 55: |
Line 55: |
| Connect to router's WebUI, go to '''VPN > IPsec Profiles''' and apply the following configuration. | | Connect to router's WebUI, go to '''VPN > IPsec Profiles''' and apply the following configuration. |
| | | |
− | [[File:Networking_rutxxx_configuration_example_ipsec_cisco_profiles_v1.png|border|class=tlt-border]] | + | [[File:Networking_rutxxx_configuration_example_ipsec_cisco_profiles_v2.png|border|class=tlt-border]] |
| | | |
| # Add '''Profile Name''' (anything you want). | | # Add '''Profile Name''' (anything you want). |
Line 71: |
Line 71: |
| # Select '''Group: Group''' (5). | | # Select '''Group: Group''' (5). |
| | | |
− | When you are do with '''IPsec Profiles''', save settings, go to '''Site-to-Site''' settings and apply the following configuration: | + | When you are done with '''IPsec Profiles''', save settings, go to '''Site-to-Site''' settings and apply the following configuration: |
| | | |
| [[File:Networking_rutxxx_configuration_example_ipsec_cisco_s2s_v2.png|border|class=tlt-border]] | | [[File:Networking_rutxxx_configuration_example_ipsec_cisco_s2s_v2.png|border|class=tlt-border]] |
Line 81: |
Line 81: |
| # Write '''RUT Public IP'''. | | # Write '''RUT Public IP'''. |
| # Add '''Pre Shared Key''' (a shared password used for authentication between the peers. The value of this field must match on both instances). | | # Add '''Pre Shared Key''' (a shared password used for authentication between the peers. The value of this field must match on both instances). |
− | # Disable '''Minimum Key complexity''. | + | # Disable '''Minimum Key complexity'''. |
− | # Select '''Local Identifier Type''' (IP address). | + | # Select '''Local Identifier Type''' (IP Address). |
| # Write '''Local Identifier''' (Cisco LAN IP address). | | # Write '''Local Identifier''' (Cisco LAN IP address). |
| # Select '''Local IP Type''' (Subnet). | | # Select '''Local IP Type''' (Subnet). |
− | # IP Address: Local network | + | # Write '''IP Address''' (Cisco local network). |
− | # Subnet Mask: Network Mask | + | # Add '''Subnet Mask''' (network mask). |
− | # Remote Identifier Type: Remote WAN IP | + | # Select '''Remote Identifier Type''' (Remote WAN IP). |
− | # Remote Identifier: 192.168.10.1 | + | # Write '''Remote Identifier''' (RUT LAN IP). |
− | # Remote IP Type: Subnet | + | # Select '''Remote IP Type''' (Subnet). |
− | # IP Address: 192.168.10.0 | + | # Add '''IP Address''' (RUT local network). |
− | # Subnet Mask: 255.255.255.0 | + | # Add '''Subnet Mask''' (RUT local network mask). |
| | | |
| ==Testing the setup== | | ==Testing the setup== |