Jump to content

Providing connectivity for Helium miners using the RUT240: Difference between revisions

m
no edit summary
m (Certwarning image fixed)
mNo edit summary
 
Line 44: Line 44:
[[File:WebUIloginpage RUTOS.png|1039x1039px]]
[[File:WebUIloginpage RUTOS.png|1039x1039px]]


Once logged in, a prompt to change the password will be shown. Change password to meet the requirements, then proceed by clicking “'''Save'''”:
Once logged in, a prompt to change the password will be shown. Change password to meet the requirements, then proceed by clicking “'''Submit'''”:


[[File:ChangePassword RUTOS.png]]
[[File:ChangePassword RUTOS.png]]


Next, we need to configure basic settings to prepare our router. In '''Step 1''' of setup wizard change the "'''Configuration Mode'''" to "'''Advanced'''", then click on “'''Sync with browser'''” option and choose your desired time zone. Once done, click on “'''Next'''”.
Next, we need to configure basic settings to prepare our router. A setup wizard will open after entering the new password. In '''Step 1''' of setup wizard change the "'''Configuration Mode'''" to "'''Advanced'''", then click on “'''Sync with browser'''” option and choose your desired time zone. Once done, click on “'''Next'''”.


[[File:FirstLoginTime RUTOS.png|1140x1140px]]
[[File:FirstLoginTime RUTOS.png|1140x1140px]]
Line 64: Line 64:
[[File:FirstLoginWiFi RUTOS.png|1125x1125px]]
[[File:FirstLoginWiFi RUTOS.png|1125x1125px]]


In '''Step 5''' we can connect our router to Teltonika’s '''Remote Management System'''. More information about the Teltonika '''RMS''' can be found [https://teltonika-networks.com/product/rms/ here].
In '''Step 5''' we can connect our router to Teltonika '''Remote Management System'''. More information about the Teltonika '''RMS''' can be found [https://teltonika-networks.com/product/rms/ here].


[[File:FirstLoginRMS RUTOS.png|1123x1123px]]
[[File:FirstLoginRMS RUTOS.png|1123x1123px]]
Line 91: Line 91:
[[File:ToLAN RUTOS.png|446x446px]]
[[File:ToLAN RUTOS.png|446x446px]]


Once there, edit the default LAN interface by clicking a pencil icon:
Once there, edit the default LAN interface by clicking the pencil icon:


[[File:EditLAN RUTOS.png|1102x1102px]]
[[File:EditLAN RUTOS.png|1102x1102px]]
Line 99: Line 99:
[[File:LANAddStatic RUTOS.png|1100x1100px]]
[[File:LANAddStatic RUTOS.png|1100x1100px]]


Configuration window will load. Enter a MAC address of the Helium miner and any desired IP address (can be current LAN IP) in their respective fields:
Configuration window will load. Enter MAC address of the Helium miner and any desired IP address (can be current LAN IP) in their respective fields:


[[File:StaticIPLAN RUTOS.png|1097x1097px]]   
[[File:StaticIPLAN RUTOS.png|1097x1097px]]   
Line 107: Line 107:
[[File:StaticIPLAN2 RUTOS.png|1093x1093px]]
[[File:StaticIPLAN2 RUTOS.png|1093x1093px]]


When done, click on “'''Save & Apply'''” button to save the changes on the interface.
When done, click on “'''Save & Apply'''” button to save the changes on the LAN interface.


===Configuring the port forward rule ===
===Configuring the port forward rule ===
----If the internet is up and running, proceed to the port forward configuration page by navigating to "'''Network>Firewall>Port Forwards'''":
----If the internet is up and running, proceed to the port forward configuration page by navigating to "'''Network>Firewall>Port Forwards'''":
[[File:NavigateToPortFW RUTOS.png]]
[[File:NavigateToPortFW RUTOS.png]]




Line 130: Line 129:
[[File:PortFWfinalresult RUTOS.png|1097x1097px]]
[[File:PortFWfinalresult RUTOS.png|1097x1097px]]


A new window will appear. Change the "'''Protocol'''" field from "'''TCP+UDP'''" to "'''TCP'''" only. Once done, scroll down to the bottom of the window and "'''Save & Apply'''" the settings. The configuration window should look like this before saving the settings (Internal IP address may differ):
A new window will pop up. Change the "'''Protocol'''" field from "'''TCP+UDP'''" to "'''TCP'''" only. Once done, scroll down to the bottom of the window and click on "'''Save & Apply'''" to save the settings. The configuration window should look like this before saving the settings (internal IP address field may differ):


[[File:PortFWfinalresult2 RUTOS.png]]
[[File:PortFWfinalresult2 RUTOS.png]]


If every configuration field is correct and the rule has been applied, the port forward rule should appear in the table in a similar fashion:
If every configuration field is correct and the rule has been applied, the port forward rule should appear in the port forwards table in a similar fashion:


[[File:PortFWfinaltable RUTOS.png|1118x1118px]]
[[File:PortFWfinaltable RUTOS.png|1118x1118px]]
Line 182: Line 181:
There, MAC address of Helium miner as well as its current LAN IP address should be visible:
There, MAC address of Helium miner as well as its current LAN IP address should be visible:


[[File:IP-Lease RUTOS.png|1088x1088px]]
[[File:IP-Lease RUTOS.png|1088x1088px]]  


After the noted fields been configured in a correct manner, make sure to apply configuration by scrolling down to the bottom of page and click “'''Save & Apply'''”. Eventually, the Helium miner should get an external IP address.  
After the necessary configuration has been set, make sure to apply configuration by scrolling down to the bottom of mobile interface configuration page and click “'''Save & Apply'''”. Eventually, the Helium miner should get an external IP address from the router.  


===Optional configuration: set WAN port as LAN===
===Optional configuration: set WAN port as LAN===
Line 320: Line 319:
[[File:WGif-setup RUTOS.png]]
[[File:WGif-setup RUTOS.png]]


Next, click on "Advanced settings" on the left side of the configuration page and fill in the following line:
Next, click on "'''Advanced settings'''" on the left side of the configuration page and fill in the following line:


"'''MTU'''": 1420
"'''MTU'''": 1420
Line 327: Line 326:




Leave the metric empty. Once done, move to the bottom and add a new peer by entering its name in the "Add new instance" field:
 
Leave the metric empty. Once done, move to the bottom of the configuration page and add a new peer by entering its name in the "'''Add new instance'''" field:


[[File:AddWGpeer RUTOS.png|1126x1126px]]
[[File:AddWGpeer RUTOS.png|1126x1126px]]
Line 333: Line 333:
Once the peer configuration window opens up, fill in the fields as follows:
Once the peer configuration window opens up, fill in the fields as follows:


"'''Public Key'''": copy and paste the public key of your peer (which was generated by the virtual private server)
"'''Public Key'''": copy and paste the public key of your peer (public key which was generated by the virtual private server)


"'''Allowed IPs'''": 10.0.1.1/32
"'''Allowed IPs'''": 10.0.1.1/32