Line 8: |
Line 8: |
| }} | | }} |
| | | |
− | {{#ifeq: {{{series}}} | RUT9 |<i><b>Note</b>: <b>[[{{{name}}} RS232/RS485 (legacy WebUI)#RS232|click here]]</b> for the old style WebUI (FW version {{Template: Networking_device_manual_latest_fw | series = RUT9XX}} and earlier) user manual page.</i>|}} | + | {{#ifeq: {{{series}}}| RUT9 |<i><b>Note</b>: <b>[[{{{name}}} RS232/RS485 (legacy WebUI)#RS232|click here]]</b> for the old style WebUI (FW version {{Template: Networking_device_manual_latest_fw | series = RUT9XX}} and earlier) user manual page.</i>|}} |
| ==Summary== | | ==Summary== |
| | | |
Line 425: |
Line 425: |
| <tr> | | <tr> |
| <td>Device</td> | | <td>Device</td> |
− | <td>{{Template: Networking_rutos_manual_serial_ports | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}; default: <b>{{Template: Networking_rutos_manual_default_serial_port | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}</b></td> | + | <td>{{#ifeq:{{{default}}}|mbus|MBUS| {{Template: Networking_rutos_manual_serial_ports | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}}}; default: <b>{{#ifeq:{{{default}}}|mbus|MBUS| {{Template: Networking_rutos_manual_default_serial_port | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}}}</b></td> |
| <td>Specifies which serial port will be used for serial communication.</td> | | <td>Specifies which serial port will be used for serial communication.</td> |
| </tr> | | </tr> |
Line 440: |
Line 440: |
| <tr> | | <tr> |
| <td>Stop bits</td> | | <td>Stop bits</td> |
− | <td>1 {{!}} 2; default: <b>1</b></td> | + | <td>{{#switch: {{{name}}} | TRB143 = 1; default: <b>1</b> | #default = 1 {{!}} 2; default: <b>1</b> }}</td> |
| <td>Stop bits sent at the end of every character allow the receiving signal hardware to detect the end of a character and to resynchronise with the character stream. Electronic devices usually use one stop bit. Two stop bits are required if slow electromechanical devices are used.</td> | | <td>Stop bits sent at the end of every character allow the receiving signal hardware to detect the end of a character and to resynchronise with the character stream. Electronic devices usually use one stop bit. Two stop bits are required if slow electromechanical devices are used.</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Parity</td> | | <td>Parity</td> |
− | <td>None {{!}} Odd {{!}} Even {{!}} Mark {{!}} Space; default: <b>None</b></td> | + | <td>{{#switch: {{{name}}} | TRB143 = Even {{!}} default: Even | #default = None {{!}} Odd {{!}} Even {{!}} Mark {{!}} Space; default: <b>None</b> }}</td> |
| <td>In serial transmission, parity is a method of detecting errors. An extra data bit is sent with each data character, arranged so that the number of 1 bits in each character, including the parity bit, is always odd or always even. If a byte is received with the wrong number of 1s, then it must have been corrupted. However, an even number of errors can pass the parity check. | | <td>In serial transmission, parity is a method of detecting errors. An extra data bit is sent with each data character, arranged so that the number of 1 bits in each character, including the parity bit, is always odd or always even. If a byte is received with the wrong number of 1s, then it must have been corrupted. However, an even number of errors can pass the parity check. |
| <ul> | | <ul> |
Line 522: |
Line 522: |
| </table> | | </table> |
| | | |
− | [[File:Networking rutos manual serial utilities over ip mbus configuration security_v1.png|border|class=tlt-border]] | + | [[File:Networking rutos manual serial utilities over ip mbus configuration security_v2.png|border|class=tlt-border]] |
| | | |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |