Line 23: |
Line 23: |
| | | |
| [[File:Networking_rutos_manual_mbus_client_general_settings.png|border|class=tlt-border]] | | [[File:Networking_rutos_manual_mbus_client_general_settings.png|border|class=tlt-border]] |
− |
| |
− | [[File:Networking_rutos_manual_mbus_client_device_configuration.png|border|class=tlt-border]]
| |
| | | |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
Line 44: |
Line 42: |
| </table> | | </table> |
| | | |
− | The Devices section is used to configure the general device instance. The figure below is an example of the M-Bus device and the table below provides information on the fields contained in that section:
| + | |
| + | |
| | | |
| ===Devices=== | | ===Devices=== |
Line 52: |
Line 51: |
| | | |
| [[File:Networking_rutos_manual_mbus_client_devices_add.png|border|class=tlt-border]] | | [[File:Networking_rutos_manual_mbus_client_devices_add.png|border|class=tlt-border]] |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | The Devices section is used to configure the general device instance. The figure below is an example of the M-Bus device and the table below provides information on the fields contained in that section: |
| + | |
| + | [[File:Networking_rutos_manual_mbus_client_device_configuration.png|border|class=tlt-border]] |
| | | |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
Line 80: |
Line 87: |
| </tr> | | </tr> |
| </table> | | </table> |
| + | |
| | | |
| | | |
Line 89: |
Line 97: |
| | | |
| [[File:Networking_rutos_manual_mbus_client_data_collecting_groups.png|border|class=tlt-border]] | | [[File:Networking_rutos_manual_mbus_client_data_collecting_groups.png|border|class=tlt-border]] |
| + | |
| + | |
| + | |
| | | |
| Before saving, you can check if your configuration works accordingly by pressing the Test Configuration button. You should see the data in a pop-up field. | | Before saving, you can check if your configuration works accordingly by pressing the Test Configuration button. You should see the data in a pop-up field. |
Line 121: |
Line 132: |
| </tr> | | </tr> |
| </table> | | </table> |
| + | |
| | | |
| | | |
Line 199: |
Line 211: |
| </tr> | | </tr> |
| </table> | | </table> |
| + | |
| | | |
| | | |
Line 236: |
Line 249: |
| </tr> | | </tr> |
| </table> | | </table> |
| + | |
| | | |
| | | |
Line 283: |
Line 297: |
| </tr> | | </tr> |
| </table> | | </table> |
| + | |
| | | |
| | | |
Line 340: |
Line 355: |
| ===IP filter=== | | ===IP filter=== |
| ---- | | ---- |
| + | |
| + | The IP Filter section is used for configuring which network is allowed to communicate with the device. You may add a new instance by selecting the Interface and pressing Add. |
| | | |
| [[File:Networking_rutos_manual_mbus_gateway_ip_filter.png|border|class=tlt-border]] | | [[File:Networking_rutos_manual_mbus_gateway_ip_filter.png|border|class=tlt-border]] |