Line 75: |
Line 75: |
| [[File:Tag_Based_Physical_Settings_2.png|border|class=tlt-border|center]] | | [[File:Tag_Based_Physical_Settings_2.png|border|class=tlt-border|center]] |
| | | |
− | | + | ====Lan Interfaces After Configration==== |
− | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_lan_creation_v1.png|border|class=tlt-border]]
| |
− | | |
− | The configuration window will appear, in the "Protocol" drop-down box select Static.
| |
− | | |
− | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_lan_protocol_v1.png|border|class=tlt-border]]
| |
− | | |
− | Add the new IP address for the LAN interface
| |
− | | |
− | '''''Note:''''' ''The LANS must be on a different subnet from each other. For example: LAN 192.168.1.1, LAN_2, 192.168.10.1, LAN_3 192.168.15.1''
| |
− | | |
− | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_lan_ip_address_v1.png|border|class=tlt-border]]
| |
− | | |
− | Click on Setup DHCP Server
| |
− | | |
− | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_lan_dhcp_v1.png|border|class=tlt-border]]
| |
− | | |
− | The parameters will be set to default parameters for the DHCP server for the LAN. You can change these to suit your requirements. Click Save & Apply.
| |
− | | |
− | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_lan_dhcp_enable_v1.png|border|class=tlt-border]]
| |
− | | |
− | ===Creating new VLANS===
| |
− | | |
− | Go to Network → VLAN → Port-Based VLANs and click "Add" to create two new VLANs.
| |
− | | |
− | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_add_vlan_v1.png|border|class=tlt-border]]
| |
− | | |
− | Go to VLAN 1 and turn off “Untagged” for LAN 2 and LAN 3.
| |
− | | |
− | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_vlan_off_v1.png|border|class=tlt-border]]
| |
− | | |
− | Under VLAN 2 and choose the drop-down box under LAN 2 and select “Tagged”. Then do the same for VLAN 3 under LAN 3 drop-down box choose “Tagged”.
| |
− | Click Save & Apply
| |
− | | |
− | '''''Note:''''' ''You can Tag more than one VLAN for the Same Port with “Tagged”, meaning multiple Tagged VLANs can be used on the same Port. In this example I have turned on “Tagged” for VLAN 1 and VLAN 3 on LAN 3 for testing later.''
| |
− | | |
− | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_vlan_tagged_v1.png|border|class=tlt-border]]
| |
− | | |
− | ===Assigning LAN networks===
| |
− | | |
− | Go to Network → Interfaces
| |
− | | |
− | Click “edit” on the new LAN interfaces.
| |
− | | |
− | In the configuration window, choose the "Physical Settings" tab and add the Ethernet port you choose to assign to the LAN. ''In this case I assigned VLAN 2 to LAN_2 on Ethernet port 2.'' Click Save & Apply
| |
− | | |
− | | |
− | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_lan_physical_settings_v1.png|border|class=tlt-border]]
| |
− | | |
− | The new LAN interface should now show active.
| |
| | | |
| [[File:Networking_rut_manual_vlan_tagged_based_device_settings_lan_interfaces_v1.png|border|class=tlt-border]] | | [[File:Networking_rut_manual_vlan_tagged_based_device_settings_lan_interfaces_v1.png|border|class=tlt-border]] |