Line 73: |
Line 73: |
| <b>Step 4</b>: configure DMVPN NHRP parameters: | | <b>Step 4</b>: configure DMVPN NHRP parameters: |
| | | |
− | <nowiki>###</nowiki> Highlight the importance of "Redirect option here". This is essentially what makes P3 possible.
| + | In the NHRP parameters section, it is important to enable REDIRECT option, which is essential to our Phase 3 configuration. |
| | | |
| <br>[[File:DMVPN HUB Phase3 example4.png|border|class=tlt-border]] | | <br>[[File:DMVPN HUB Phase3 example4.png|border|class=tlt-border]] |
Line 88: |
Line 88: |
| | | |
| - Set AS to 65000 | | - Set AS to 65000 |
| + | |
| + | - Set BGP router ID for easier management. |
| | | |
| - Set announcement network(s). Routes to these networks will be shared over BGP. We used 192.168.1.0/24 | | - Set announcement network(s). Routes to these networks will be shared over BGP. We used 192.168.1.0/24 |
| | | |
− | <nowiki>###</nowiki> Highlight the fact that "NHRP routes" selection should exist under "Redistribution options"
| + | - "NHRP routes" selection should be applied under the "Redistribution options" section |
− | | |
− | <nowiki>###</nowiki> Probably a good idea to set BGP router ID here using GRE interface IPs to avoid confusion and make troubleshooting easier
| |
| | | |
| <br>[[File:DMVPN HUB Phase3 example5.png|border|class=tlt-border]] | | <br>[[File:DMVPN HUB Phase3 example5.png|border|class=tlt-border]] |
Line 101: |
Line 101: |
| <b>Step 2</b>: Create BGP Peer Group: | | <b>Step 2</b>: Create BGP Peer Group: |
| | | |
− | - Add Neighbor address (We used 10.0.0.1 and 10.0.0.2) | + | - Add a Neighbor address for SPOKE 1 and SPOKE 2 (We used 10.0.0.1 and 10.0.0.2 which will be in the same subnet as our hub 10.0.0.254) |
− | | |
− | <nowiki>###</nowiki> Explanation needed what these IP addresses are - this might not be clear enough for end-users that this is spoke devices GRE IP address
| |
− | | |
− | <nowiki>###</nowiki> Also need to quickly mention about other settings
| |
| | | |
− | <nowiki>###</nowiki> Remote AS is empty here - I don't remember now, but is this intended?
| + | - Leave other settings as default. |
| | | |
| <br>[[File:DMVPN HUB Phase3 example6.png|border|class=tlt-border]] | | <br>[[File:DMVPN HUB Phase3 example6.png|border|class=tlt-border]] |
Line 115: |
Line 111: |
| <b>Step 3</b>: Add two BGP peers for each spoke: | | <b>Step 3</b>: Add two BGP peers for each spoke: |
| | | |
− | <nowiki>###</nowiki> Need to mention that "Let's move on to spokes BGP configuration now.", because it looks a bit confusing
| + | Now let's create BGP peers for Spokes on the same page. Add two new BGP peers with the following parameters: |
| | | |
| Peer 1. | | Peer 1. |
Line 129: |
Line 125: |
| - Set Remote address as 10.0.0.2 | | - Set Remote address as 10.0.0.2 |
| | | |
− | <nowiki>###</nowiki> Briefly mention that other fields are not mandatory, but changes can be done if needed (aka "we will keep other settings as their default values for this configuration example" statement)
| + | We will keep other settings as their default values for this configuration example. |
| | | |
| <br>[[File:DMVPN HUB Phase3 example7.png|border|class=tlt-border]] | | <br>[[File:DMVPN HUB Phase3 example7.png|border|class=tlt-border]] |