TSW304 Powering Options: Difference between revisions
Gytispieze (talk | contribs) (Created page with "{{Template: networking_tsw2xx_manual_powering_options | name = TSW340 | series = TSW3 | poe = 0 }}") |
Gytispieze (talk | contribs) No edit summary |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
{{Template: networking_tsw2xx_manual_powering_options | {{Template: networking_tsw2xx_manual_powering_options | ||
| name = | | name = TSW304 | ||
| series = TSW3 | | series = TSW3 | ||
| poe = 0 | | poe = 0 | ||
| passive_poe = 1 | |||
| file_lan1 = Networking_tsw304_manual_powering_options_lan1.png | |||
| size_lan1 = 400 | |||
}} | }} | ||
Latest revision as of 10:23, 21 February 2023
Main Page > TSW Switches > TSW304 > TSW304 Manual > TSW304 Powering OptionsThis chapter contains information on powering options supported by TSW304 switch.
The switch has a 2 pin power socket and can be powered by a 7-57 VDC and 9-40 VAC power supply unit (PSU). Refer to the image below for the power socket's pinout information:
Power socket
2 pin power socket
| The power socket is bipolar. |  |
If you decide not to use the standard 50 VDC power supply unit and want to power the device with other voltages (7-57 VDC or 9-40 VAC), please make sure that you choose a power supply of high quality. Some power supplies can produce voltage peaks significantly higher than the declared output voltage, especially during connection and disconnection.
While the device is designed to accept input voltage of up to 57 VDC or 40 VAC peaks, high voltage power supplies can harm the device. If you want to use high voltage power supplies it is recommended to also use additional safety equipment to suppress voltage peaks from the power supply.
Passive PoE
The device may also be powered by an Ethernet cable via the LAN1 port (9-30 VDC):
(Do not use in other ports!)
- The device is NOT COMPLIANT with the IEEE 802.3af-2003 standard: powering the device from an IEEE 802.3af-2003 power supply will damage the device as it is not rated for input voltages of the PoE standard.
- The device is NOT COMPLIANT with the IEEE 802.3at standard: it cannot power other devices over Ethernet.
| Pin | 10/100 mode B, DC on spares | T568A Color | T568B Color | Pins on plug face (socket is reversed) | |
| 1 | TX+ |  white/green stripe |
 white/orange stripe |
| |
| 2 | TX- |  green solid |
 orange solid | ||
| 3 | RX+ | white/orange stripe |
white/green stripe | ||
| 4 | DC+ | 9-30 VDC |  blue solid |
blue solid | |
| 5 | DC+ | 9-30 VDC |  white/blue stripe |
white/blue stripe | |
| 6 | RX- | orange solid |
green solid | ||
| 7 | DC- |  white/brown stripe |
white/brown stripe | ||
| 8 | DC- |  brown solid |
brown solid | ||
Ground loops
Do not connect the power supply negative terminal of our device to the chassis or earth exclusively.
This connection could cause ground loops. For example, if the antenna shield and power supply negative terminal are connected to the chassis or earth, it forms a ground loop, therefore unwanted current could flow through a device PCB ground and may cause damage.
In networking switches connecting our device power supply negative terminal to the chassis or earth could cause damage to other devices connected to the switch or unintentional power up of other devices.
