Template:Networking device leds: Difference between revisions
(Created page with "This wiki page contains information about {{{name}}} {{#ifexits: {{{series}}} | TRB | gateway | {{#ifexits: {{{series}} | RUT | router | modem }}}}") |
(Added information on Signal Strength LEDs and reset button when no User's defaults are configured.) |
||
(50 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
This wiki page contains information about {{{name}}} {{# | This wiki page contains information about {{{name}}} {{#switch: {{{series}}} | ||
| TRB14x|TRB2xx|TRB5 = gateway | |||
| TRM2xx = modem | |||
| TSW1xx|TSW2xx|TSW3|TSW0 = switch | |||
| router}} <b>LEDs</b> and their actions. | |||
__TOC__ | |||
==Power LED== | |||
The <b>power LED</b> is located on the bottom left corner of the front panel, near the power connector: | |||
[[File:{{{file_power_led}}}|{{{size_power_led}}}px]] | |||
It can perform two different actions: | |||
<table class="nd-othertables_2"> | |||
<tr> | |||
<th style="width: 550px>Action</th> | |||
<th style="width: 550px>Description</th> | |||
</tr> | |||
<tr> | |||
<td>LED turned ON</td> | |||
<td>{{#switch: {{{series}}} | |||
| TRB14x|TRB2xx|TRB5 = Gateway | |||
| TRM2xx = Modem | |||
| TSW1xx|TSW2xx|TSW3|TSW0 = Switch | |||
| Router}} is powered up</td> | |||
</tr> | |||
<tr> | |||
<td>LED turned OFF</td> | |||
<td>{{#switch: {{{series}}} | |||
| TRB14x|TRB2xx|TRB5 = Gateway | |||
| TRM2xx = Modem | |||
| TSW1xx|TSW2xx|TSW3|TSW0 = Switch | |||
| Router}} is not power up</td> | |||
</tr> | |||
</table> | |||
<!-- Use if device has eth port --> | |||
{{#ifeq: {{{eth_leds}}} | 1 | |||
|{{#ifeq: {{{name}}} | TRB140 | |||
|{{Template: Networking_{{lc:{{{name}}}}}_manual_ethernet_port_leds | |||
| file_eth_led = {{{file_eth_led}}} | |||
| size_eth = {{{size_eth}}} | |||
}} | |||
|{{Template: Networking_{{lc:{{{series}}}}}_manual_ethernet_port_leds | |||
| file_eth_led = {{{file_eth_led}}} | |||
| size_eth = {{{size_eth}}} | |||
| name = {{{name}}} | |||
}}| | |||
}} | |||
}} | |||
<!-- Use if device has SFP port --> | |||
{{#ifeq: {{{sfp_leds}}} | 1 | |||
| {{Template: Networking_{{lc:{{{series}}}}}_manual_sfp_port_leds | |||
| file_sfp_led = {{{file_sfp_led}}} | |||
| size_sfp = {{{size_sfp}}} | |||
| name = {{{name}}} | |||
}} | |||
| | |||
}} | |||
<!-- Use if device has mobile module --> | |||
{{#ifeq: {{{con}}} | 1 | |||
| {{Template: Networking_{{lc:{{{name}}}}}_manual_connection_status_leds | |||
| file_con_led = {{{file_con_led}}} | |||
| size_con = {{{size_con}}} | |||
}} | |||
| | |||
}} | |||
{{#ifeq: {{{sig}}} | 1 | |||
| {{Template: Networking_{{lc:{{{series}}}}}_manual_signal_strength_leds | |||
| file_sig_led = {{{file_sig_led}}} | |||
| size_sig = {{{size_sig}}} | |||
}} | |||
The signal strength LEDs can also be used as a <b>time indicator for holding the reset button</b>. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a <b>User's default configuration reset</b> and 12 seconds (by default) to initiate a <b>Factory reset</b>. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a <b>Factory reset</b>. If the button was held down longer than 20 seconds (by default) no action will be taken. | |||
While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with <b>{{{name}}}</b>, when all {{{sig_led_num}}} signal strength LEDs are lit up, they represent that {{#expr: {{{sig_led_num}}} * 2}} (LED number multiplied by 2) seconds have passed since you pressed down on the reset button. | |||
After releasing the button at one of the reset periods, all {{{sig_led_num}}} LEDs will start blinking every 1 second. This signifies that the router <b>has begun the reset</b>. | |||
| | |||
}} | |||
[[Category:{{{name}}} Manual]] |
Revision as of 11:07, 10 March 2023
This wiki page contains information about {{{name}}} router LEDs and their actions.
Power LED
The power LED is located on the bottom left corner of the front panel, near the power connector:
[[File:{{{file_power_led}}}|{{{size_power_led}}}px]]
It can perform two different actions:
Action | Description |
---|---|
LED turned ON | Router is powered up |
LED turned OFF | Router is not power up |
[[Category:{{{name}}} Manual]]