Template:Networking device leds: Difference between revisions

Latest revision as of 11:11, 15 March 2023

This wiki page contains information about {{{name}}} router LEDs and their actions.

Power LED

The power LED is located on the bottom left corner of the front panel, near the power connector:

[[File:{{{file_power_led}}}|{{{size_power_led}}}px]]

It can perform two different actions:

Action	Description
LED turned ON	Router is powered up
LED turned OFF	Router is not power up

[[Category:{{{name}}} Manual]]

@@ Line 1: / Line 1: @@
 This wiki page contains information about {{{name}}} {{#switch: {{{series}}}
-   | TRB14x = gateway
+   | TRB14x|TRB2xx|TRB5 = gateway
-  | TRB2xx = gateway
    | TRM2xx = modem
-   | TSW1xx = switch
+   | TSW1xx|TSW2xx|TSW3|TSW0 = switch
-   | router
+   | router}} <b>LEDs</b> and their actions.
-}} <b>LEDs</b> and their actions.
 __TOC__
@@ Line 11: / Line 9: @@
 ==Power LED==
-<!-- Use if device as eth port -->
+The <b>power LED</b> is located on the bottom left corner of the front panel, near the power connector:
-{{#if: {{{eth_leds|}}}
-  | <br>{{Template: Networking_{{lc:{{{series}}}}}_manual_ethernet_port_leds
+[[File:{{{file_power_led}}}|{{{size_power_led}}}px]]
-         | eth_led = {{{eth_led}}}
-         | size_eth = {{{size_eth}}}
+It can perform two different actions:
-        }}
- | {{#ifeq: {{{name}}} | TRB140
+<table class="nd-othertables_2">
-    | <br>{{Template: Networking_{{lc:{{{name}}}}}_manual_ethernet_port_leds
+    <tr>
-           | eth_led = {{{eth_led}}}
+        <th style="width: 550px>Action</th>
-           | size_eth = {{{size_eth}}}
+        <th style="width: 550px>Description</th>
-          }}
+    </tr>
-   }}
+    <tr>
+        <td>LED turned ON</td>
+        <td>{{#switch: {{{series}}}
+             | TRB14x|TRB2xx|TRB5 = Gateway
+             | TRM2xx = Modem
+             | TSW1xx|TSW2xx|TSW3|TSW0 = Switch
+             | Router}} is powered up</td>
+    </tr>
+    <tr>
+        <td>LED turned OFF</td>
+        <td>{{#switch: {{{series}}}
+             | TRB14x|TRB2xx|TRB5 = Gateway
+             | TRM2xx = Modem
+             | TSW1xx|TSW2xx|TSW3|TSW0 = Switch
+             | Router}} is not power up</td>
+    </tr>
+</table>
+<!-- Use if device has eth port -->
+{{#ifeq: {{{eth_leds}}} | 1
+ |{{#ifeq: {{{name}}} | TRB140
+   |{{Template: Networking_{{lc:{{{name}}}}}_manual_ethernet_port_leds
+     | file_eth_led = {{{file_eth_led}}}
+     | size_eth = {{{size_eth}}}
+    }}
+     |{{Template: Networking_{{lc:{{{series}}}}}_manual_ethernet_port_leds
+       | file_eth_led = {{{file_eth_led}}}
+       | size_eth = {{{size_eth}}}
+       | name = {{{name}}}
+      }}|
+  }}
+}}
+<!-- Use if device has SFP port -->
+{{#ifeq: {{{sfp_leds}}} | 1
+ | {{Template: Networking_{{lc:{{{series}}}}}_manual_sfp_port_leds
+       | file_sfp_led = {{{file_sfp_led}}}
+       | size_sfp = {{{size_sfp}}}
+       | name = {{{name}}}
+      }}
+ |
+}}
+<!-- Use if device has mobile module -->
+{{#ifeq: {{{con}}} | 1
+ | {{Template: Networking_{{lc:{{{name}}}}}_manual_connection_status_leds
+        | file_con_led = {{{file_con_led}}}
+        | size_con = {{{size_con}}}
+       }}
   |
 }}
+{{#ifeq: {{{sig}}} | 1
+ | {{Template: Networking_{{lc:{{{series}}}}}_manual_signal_strength_leds
+        | file_sig_led = {{{file_sig_led}}}
+        | size_sig = {{{size_sig}}}
+       }}
+The signal strength LEDs can also be used as a <b>time indicator for holding the reset button</b>. By default,  when you press and hold the reset button, after 6 seconds it initiates a <b>Factory reset</b>. If there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a <b>User's default configuration reset</b> and 12 seconds (by default) to initiate a <b>Factory reset</b>. If the button was held down longer than 20 seconds (by default) no action will be taken.
+While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with <b>{{{name}}}</b>, when all {{{sig_led_num}}} signal strength LEDs are lit up, they represent that {{#expr: {{{sig_led_num}}} * 2}} (LED number multiplied by 2) seconds have passed since you pressed down on the reset button.
+After releasing the button at one of the reset periods, all {{{sig_led_num}}} LEDs will start blinking every 1 second. This signifies that the router <b>has begun the reset</b>.
+ |
+}}
+[[Category:{{{name}}} Manual]]