TSW212 Administration

The information in this page is updated in accordance with firmware version TSW2_R_00.01.03.1.

Summary

This page is an overview of the Administration section of TSW212 devices.

General

The General section is used to set up some of device managerial parameters, such as changing device name. For more information on the General section, refer to figure and table below.

Field	Value	Description
General settings
Language	English | Spanish | Japanese | Portuguese | Turkish | German; default: English	Currently active language of Web interface.
Data analytics	off | on; default: off	Enables the collection of data, which is used to improve the quality and user experience of our products. It includes sending information about the device and the usage of the Web interface. The data is collected in compliance with the Privacy policy.
Device name and hostname
Device name	string; default: TSW212	Device model name.
Hostname	string; default: Teltonika-TSW212.com	Device hostname. This can be used for communication with other LAN hosts.
Reset Button Configuration
Action		The type of action when the reset button is triggered.
Min time	integer [0..60]; default: none	Minimum time (in seconds) the button needs to be held to perform an action.
Max time	integer [1..60]; default: none	Maximum time (in seconds) the button can be held to perform an action, after which no action will be performed.
Enable	off | on; default: on	Enables the action.

Date & Time

Summary

---

Network Time Protocol (NTP) is a networking protocol for clock synchronization between computer systems over packet-switched, variable-latency data networks. This chapter is an overview of the NTP section for TSW212 devices.

General

---

The Time Synchronization section lets you select time zone and synchronize the time.

The figure below is an example of the Time Synchronization section and the table below provides information about the fields contained in that section:

Field	Value	Description
Current system time	time; default: none	Current local time of the device.
Sync with browser	-(interactive button)	Click to synchronize device time and time zone to browsers, if your device time or time zone is not correct.
Time zone	time zone; default: UTC	The device will sync time in accordance with the selected time zone.

NTP

---

This section is used to configure NTP client and time servers.

Time Synchronization

---

This section is used to configure the device's time settings.

Field	Value	Description
Enable NTP Client	off | on; default: on	Turns NTP on or off.
Save time to flash	off | on; default: off	Saves last synchronized time to flash memory.
Force Servers	off | on; default: off	Forces unreliable NTP servers.
Update interval (in seconds)	integer; default: 86400	How often the device will update the time.
Offset frequency	integer; default: 0	Adjusts the minor drift of the clock so that it will run more accurately.
Count of time synchronizations	integer; default: none	The amount of times the device will perform time synchronizations. Leave empty in order to set to infinite.

Time Servers

---

This section is used to specify which time servers the device will use for time synchronization. To add more time servers to the list, click the 'Add' button.

Field	Value	Description
Hostname	ip | url; default: 0.openwrt.pool.ntp.org	NTP servers that this device uses to sync time.
Delete button	-(interactive) button	Deletes hostname.

User Settings

Change Password

---

The User settings section is used to change the password of the current user.

System Users

Summary

---

The System Users page is used to add new user accounts that can access the device with different user credentials than the default ones. The newly added users can be assigned to one of two groups, either of which can be modified to limit WebUI read/write access rights for users belonging to each specific group.

This page is unrelated to SSH users. By default, there is one SSH user named "root" and it shares the same password as the default WebUI user named "admin".

This manual page provides an overview of the Users page in TSW212 devices.

Groups

---

The Groups section lists available user groups of which there are three:

---

• root - highest level of authority. Key elements that define this group:
  • has unlimited read/write access;
  • additional users cannot be added to this group;
  • access rights for this group cannot be modified.
  
  

---

• admin - second highest level of authority. Key elements that define this group:
  • limited read access; by default, users belonging to this group cannot view these pages:
    • System → Administration → Users Settings → System Users
    • System → Maintenance → Backup
    • System → Firmware
    • System → Maintenance → CLI
  • limited write access; by default, users belonging to this group cannot view these pages:
    • System → Administration → Users Settings → System Users
    • System → Maintenance → Backup
    • System → Firmware
    • System → Maintenance → CLI
    • System → Administration → Access Control → General
  • access rights can be modified.
  
  

---

• user - lowest level of authority. Key elements that define this group:
  • no write access;
  • limited read access; by default, users belonging to this group cannot view these pages:
    • System → Administration → Users Settings → System Users;
    • System → Firmware
    • System → Maintenance → Backup
    • System → Administration → Access Control
    • System → Maintenance → Troubleshoot
    • Network
  • access rights can be modified.
  
  

---

Additional note: you can view and/or edit settings for each group by clicking the 'Edit' button next to them. More on information on how to edit group access settings is located in the following section of this manual page.

Group Settings (edit group)

---

A group's parameters can be set in its Group Settings page. To access the Groups Settings page, click the 'Edit' button next to the group's name. Below is an example of the Group Settings section:

Field	Value	Description
Write action	Allow | Deny; default: Allow	Specifies whether to deny or allow write access for users belonging the group.
Write access	path(s) to page(s); default: in the picture above	Controls the ability of users to change and execute the contents (e.g. admin/network/lan).
Read action	Allow | Deny; default: Deny	Specifies whether to deny or allow read access for users belonging the group.
Read access	path(s) to page(s); default: in the picture above	Controls the ability of users to navigate the contents (e.g. admin/network/*)

Examples

---

The easiest way to master the syntax is to navigate to page that you want to generate a path for and the copy the path from the URL of that page.

For example, to specify the path to the Network → Mobile page, navigate to the page, copy the page's URL address starting from the symbol "#" and paste it into one of the access fields:

---

However, the VPN window contains links to many different types of VPN pages. If you want to specify only one of them, you can do it as well. For example, to to specify the path to the IPsec page, add "/ipsec" to the path string:

services/vpn/ipsec

---

An asterisk (*) in the path string means that the every page from that point on is included in that path. For example, to generate a path that includes pages in the Services menu tab:

services/*

Or to simply include everything in the entire WebUI (if this path is combined with Read action: Deny, users from that group will not be able to login to the WebUI):

*

Users

---

The Users section lists all created users and provides the possibility to change their passwords and the group they belong to (with the exception of the default user "admin" which always belongs to the root group).

By default, there is only one user called "admin":

User Settings (edit user)

---

Each user's password and group parameters can be set in their User Settings pages. To access the User Settings page, click the 'Edit' button next to the user's name.

However, you may want to add a new user at first. This can be done from the Add New User section below:

1. create a username;
2. create a password for the user (must contain at least 8 characters, including at least one upper case letter and one digit);
3. click the 'Add' button;
4. click the 'Edit' next to newly added user.

---

Below is an example of a newly added user's settings page:

Field	Value	Description
Username	string; default: none	Displays the user's name.
New password	string; default: none	Create a new password for the user. The password must contain at least 8 characters, including at least one upper case letter and one digit. Another option is to use the 'Dice' icon, which generates random passwords.
Confirm new password	string; default: none	Repeat the new password.
Group	admin | user; default: user	The group to which the user belongs.
Enable SSH access	off | on; default: off	Enables SSH access (only for 'root' users).

Add New User

---

The Add New User section is used to create additional users that can access the WebUI. After a new user is added, it will appear in the Users section.

Field	Value	Description
Username	string; default: none	A custom name for the new user.
Password	string; default: none	A password for the new user. The password must contain at least 8 characters, including at least one upper case letter and one digit. Another option is to use the 'Dice' icon, which generates random passwords.
Group	admin | user; default: user	The group to which the user belongs.

Access Control

General

---

The Access Control page is used to manage local access to device.

Important: turning on remote access leaves your device vulnerable to external attackers. Make sure you use a strong password.

SSH

---

Field	Value	Description
PAM	Disabled | Enabled; default: Disabled	You can change PAM configuration .
Enable SSH access	off | on; default: on	Turns SSH access from the local network (LAN) on or off.
Port	integer [0..65535]; default: 22	Selects which port to use for SSH access.
Authentication type	Password | Key-based only | Use both; default: Password	Password - SSH access with password for root user Key-based only - enables key-based authentication only and disables password authentication for root user Use Both - use both password and public keys for authentication
Public keys	-(input field)	Public keys for ssh key-based authentication. Each individual key must be specified on a new line.

HTTP

---

Field	Value	Description
PAM	Disabled | Enabled; default: Disabled	You can change PAM configuration here.
Enable HTTP access	off | on; default: on	Turns HTTP access from the local network (LAN) to the device WebUI on or off.
HTTP Port	integer [0..65535]; default: 80	Selects which port to use for HTTP access.

HTTPS

---

Field	Value	Description
PAM	Disabled | Enabled; default: Disabled	You can change PAM configuration here.
Enable HTTPS access	off | on; default: on	Turns HTTPS access from the local network (LAN) to the device WebUI on or off.
Redirect to HTTPS	off | on; default: off	Redirects connection attempts from HTTP to HTTPS.
HTTPS Port	integer [0..65535]; default: 443	Selects which port to use for HTTPS access.
Certificate file	-(interactive button)	Download certificate file from device. Used for browsers to reach HTTPS connection.

CLI

---

Field	Value	Description
Enable CLI	off | on; default: on	Turns CLI access from the local network (LAN) on or off.
Port range	range of integers [0..65534]-[1..65535]; default: 4200-4220	Selects which ports to use for CLI access.
Shell limit	integer [1..10]; default: 5	Maximum number of active CLI connections.

PAM

---

Modify PAM Auth

---

Field	Value	Description
Enable	off | on; default: on	Turns the PAM auth on or off.
Module	TACACS+ | Radius | Local; default: Local	Specifies the PAM module that implements the service.
Type	Required | Requisite | Sufficient | Optional; default: Optional	Determines the continuation or failure behavior for the module
WebUI PAM auth option: Enable for all users	off | on; default: off	Turn on PAM authentication for all users. It will allow login with users that are not created on the device.
WebUI PAM auth option: Select users	-(list)	Select users for PAM authentication.
Radius: Enable for all users	off | on; default: off	Turn on PAM authentication for all users. It will allow login with users that are not created on the device.
Radius: Require Message-Authenticator	off | on; default: on	Require and validate Message-Authenticator RADIUS attribute on Access-Request replies.
TACACS+/Radius: Server	ip4 | ip6; default: none	The IP address of the RADIUS server
TACACS+/Radius: Secret	string; default: none	RADIUS shared secret
TACACS+/Radius: Port	integer [0..65535]; default: 49/1812	RADIUS server authentication port
Radius: Timeout	integer [3..10]; default: 3	Timeout in seconds waiting for RADIUS server reply.

Security

---

The Security tab provides the possibility to enable/disable blocking IP's service and delete blocked devices from the list.

Login Attempts

---

Field	Value	Description
Source	IP address	Shows the IP address from which the connection failed.
Destination	IP address	Shows yours device IP adress
Port (protocol)	Port number	Shows the port number from which the connection failed.
Status	Attempt count | Blocked	Shows the number of failed attempts to connect to device. Indicates whether the source address is blocked or not.
Reset	Check box	Allows you to select multiple IP addresses.
Actions	-(interactive button)	Allows you to select multiple IP addresses.
Unblock all	-(interactive button)	Deletes instance.
Unblock selected	-(interactive button)	Unblocks selected source adresses from the list.

IP Block Settings

---

IP Block Settings can be found by pressing 'Settings' button under security tab:

Field	Value	Description
Enable	off | on; default: on	Enable or disable blocking IP's if they have reached the set amount of failed times.
Type	Timed blocking | Permanent blocking; default: Timed blocking	You can choose an option of a blocking type.
Fail count	integer [1..1000]; default: 10	An amount of times IP address can try to access SSH or WebUI before being blocked.
Clean after reboot	off | on; default: off	If enabled, blocked loging attempts list will be cleared on device reboot.

Profiles

Summary

Configuration profiles provide a way to create multiple distinct device configuration sets and apply them to the device based on current user requirements. This chapter is an overview of the Profiles page in TSW212 devices.

Configuration Profiles

This section displays user defined configuration profiles:

---

To create a new profile, configure the device in accordance with your needs, go to this page, enter a custom name for the profile and click the 'Add' button. You can also choose to create a profile without any previous configurations. A new profile with the given name will appear in the "configuration profiles" list:

The 'Apply' button applies the adjacent configuration on the device.

Scheduler

The Profile Scheduler provides a possibility to set up a schedule of when the device should use one profile configuration or another.

Check Profile Scheduler Instance Example to get a better understanding at how Profile Scheduler Instances works.

General Configuration

---

The General Configuration section is used to enable the Scheduler itself. Created instances won't work unless this option is turned on.

Profile Scheduler Instances

---

The Profile Scheduler Instances section allows you to create profile Instances to be enabled during specific time intervals. To add a new Instance click Add button.

Note: new Instance can only be created if there is at least one custom profile created.

Profile Scheduler Instance Configuration

---

This page is used to configure profile, time and day of selected scheduler instance. Refer to the figure and table below for information on the Profile Scheduler Instance Configuration fields:

Field	Value	Description
Enable	off | on; default: off	Enable selected instance for scheduler.
Profile	profiles; default: none	Select profile which will be applied during specified time interval.
Interval Type	Weekdays | Month Days; default: Weekdays	Depending on your needs select whether you want to configure weekdays or specific month days.
Start Time	time; default: 12:00	Enter time of the start of interval in which scheduler will switch profiles.
End Time	time; default: 12:00	Enter time of the end of interval in which scheduler will switch profiles back.
Interval Type: Weekdays
Start Day	Weekday [Monday..Sunday]; default: Sunday	Select a day of the start of interval in which scheduler will switch profiles.
End Day	Weekday [Monday..Sunday]; default: Sunday	Select a day of the end of interval in which scheduler will switch profiles back.
Interval Type: Month Days
Start Day	Day of month [1..31]; default: 1	Select a day of the start of interval in which scheduler will switch profiles.
End Day	Day of month [1..31]; default: 1	Select a day of the end of interval in which scheduler will switch profiles back.
Force last day	off | on; default: off	Force intervals to accept last day of month as valid option if selected day doesn't exist in ongoing month.

Profile Scheduler Instance Example

---

Scheduler will use profile instance if it is enabled and it's time interval matches device's date, otherwise default profile will be used.

Example - we have 3 profiles in total:

• default
• Profile A
• Profile B

We create profile instances for Profiles A and B:

• Profile A: 08:00 - 11:00
• Profile B: 13:00 - 20:00

During 11:00 - 13:00 and 20:00 - 08:00 default profile will be used.