Template:Networking tswos manual diagnostics: Difference between revisions

Latest revision as of 08:19, 25 October 2023

The information in this page is updated in accordance with firmware version .

Network Diagnostics

Diagnostics

This Diagnostcis section is used to execute simple network diagnostic tests, including ping, traceroute and nslookup.

Field	Value	Description
Method	Ping \| Traceroute \| Nslookup; default: Ping	Specifies the diagnostics method. Ping - sends ICMP requests to the specified address. Traceroute - displays the path that packets have to take in order to reach the specified address. Nslookup - obtains domain name address and IP address mapping information.
Protocol	IPv4 \| IPv6; default: IPv4	Selects the IP (Internet Protocol) version.
Address	ip; default: none	IP address or hostname to perform the diagnostic test on.
Perform	-(interactive) button	Performs the diagnostic test.

Cable Diagnostic

This Cable Diagnostcis service is dedicated to provide information about cable status and length. Full cable diagnostic is performed only when the cable is connected to the switch device. When the cable is fully connected only the cable length measurements will be provided. Note: the provided cable information may not be fully accurate and margin of error could be expected.

To run cable diagnostic, select ports and press 'Run Diagnostic' button:

Cable Diagnostic Results

Field Name	Description
Pair	Cable pair number.
Status	Normal - cable connected. Short - short circuit due to bad contact. Open - connection is open on the other end. Crosstalk - connection is broken due to cable quality.
Lenght (m)	Cable length range. Possible mistake of calculation - 10 meters.
Full location (m)	Location of cable damage when status is crosstalk.

[[Category:{{{name}}} System section]]

@@ Line 1: / Line 1: @@
-{{Template: Networking_rutos_manual_fw_disclosure
+{{Template: Networking_device_manual_fw_disclosure
-| fw_version ={{Template: Networking_rutos_manual_latest_fw
+| series = {{{series}}}
+| name   = {{{name}}}
+| fw_version ={{Template: Networking_device_manual_latest_fw
   | series = {{{series}}}
   | name   = {{{name}}}
@@ Line 7: / Line 9: @@
 __TOC__
 ==Network Diagnostics==
 ===Diagnostics===
 ----
@@ Line 47: / Line 48: @@
 ==Cable Diagnostic==
+===Cable Diagnostic===
 ----
 This <b>Cable Diagnostcis</b> service is dedicated to provide information about cable status and length. Full cable diagnostic is performed only when the cable is connected to the switch device. When the cable is fully connected only the cable length measurements will be provided. Note: the provided cable information may not be fully accurate and margin of error could be expected.
@@ Line 54: / Line 56: @@
 [[File:Networking_tswos_manual_diagnostics_cable_diagnostics.png|border|class=tlt-border]]
-[[Category:{{{name}}} Services section]]
+===Cable Diagnostic Results===
+----
+[[File:Networking_tswos_manual_diagnostics_cable_diagnostics_results.png|border|class=tlt-border]]
+<table class="nd-othertables_2">
+    <tr>
+        <th width="250">Field Name</th>
+        <th width="900">Description</th>
+    </tr>
+    <tr>
+        <td>Pair</td>
+        <td>Cable pair number.</td>
+    </tr>
+        <tr>
+        <td>Status</td>
+        <td><li>Normal - cable connected.</li>
+            <li>Short - short circuit due to bad contact.</li>
+            <li>Open - connection is open on the other end.</li>
+            <li>Crosstalk - connection is broken due to cable quality.</li>
+        </td>
+    </tr>
+    <tr>
+        <td>Lenght (m)</td>
+        <td>Cable length range. Possible mistake of calculation - 10 meters.</td>
+    </tr>
+    <tr>
+        <td>Full location (m)</td>
+        <td>Location of cable damage when status is crosstalk.</td>
+    </tr>
+</table>
+[[Category:{{{name}}} System section]]