Line 17: |
Line 17: |
| }}}} | | }}}} |
| | | |
− | ==SSIDs== | + | ==Wireless == |
| | | |
| {{#switch: {{{wifi}}} | | {{#switch: {{{wifi}}} |
Line 24: |
Line 24: |
| }} | | }} |
| | | |
− | ==={{#switch:{{{series}}}|TAP100|TAP200=SSIDS|#default=WiFi 2.4 GHz}} {{#switch:{{{series}}}|TAP100|TAP200=|#default={{#ifeq:{{{wifi}}}|5|& 5 GHz|}}}}=== | + | ===SSIDS=== |
− | | + | ---- |
− | The <b>{{#switch:{{{series}}}|TAP100|TAP200=SSIDS|#default=WiFi 2.4 GHz}} {{#switch:{{{series}}}|TAP100|TAP200=|#default={{#ifeq:{{{wifi}}}|5|& 5 GHz|}}}}</b> section is used to configure your wireless access points (AP) and wireless clients (STA). | + | The <b>SSIDs</b> section is used to configure your wireless access points (AP) and wireless clients (STA). |
| | | |
| {{#switch:{{{name}}} | | {{#switch:{{{name}}} |
Line 36: |
Line 36: |
| }} | | }} |
| | | |
− | Above is the overview of the {{#switch:{{{series}}}|TAP100|TAP200=SSIDS|#default=Wireless}} Overview window. It displays active access points{{#switch:{{{series}}}|TAP100|TAP200=.|#default= and stations.}} | + | Above is the overview of the SSIDS Overview window. It displays active access points{{#switch:{{{series}}}|TAP100|TAP200=.|#default= and stations.}} |
| Here you can turn on or off your WiFi interfaces, remove them or start configuring by clicking on | | Here you can turn on or off your WiFi interfaces, remove them or start configuring by clicking on |
| [[File:Networking rutx manual edit button v1.png]] <b>Edit</b> button on the right side of interface.{{#switch:{{{series}}}|TAP100|TAP200=|#default= You can also configure your WiFi devices by clicking [[File:Networking rutx manual edit button v1.png]] <b>Edit</b> button in the right side of each table header. To configure your Wireless device as Client press '''Scan''' button to scan the surrounding area and attempt to connect to a new wireless access point.}} | | [[File:Networking rutx manual edit button v1.png]] <b>Edit</b> button on the right side of interface.{{#switch:{{{series}}}|TAP100|TAP200=|#default= You can also configure your WiFi devices by clicking [[File:Networking rutx manual edit button v1.png]] <b>Edit</b> button in the right side of each table header. To configure your Wireless device as Client press '''Scan''' button to scan the surrounding area and attempt to connect to a new wireless access point.}} |
Line 46: |
Line 46: |
| |}} | | |}} |
| | | |
− | ===={{#ifeq:{{{series}}}|TAP100|Radio|Global}} Settings====
| + | {{#switch:{{{series}}}|TAP100|TAP200= ===Radio Settings===|#default= ====Global Settings====}} |
| | | |
− | The <b>{{#ifeq:{{{series}}}|TAP100|Radio|Global}} Settings</b> section is used for configuring WiFi hardware parameters. You can find this section {{#ifeq:{{{series}}}|TAP100||by clicking the 'Edit' button next to a wireless device (<u>not an interface</u>)}} in the Network → {{#ifeq:{{{series}}}|TAP100|Radio page.|Wireless page:}} | + | The <b>{{#switch:{{{series}}}|TAP100|TAP200=Radio|#default=Global}} Settings</b> section is used for configuring WiFi hardware parameters. You can find this section {{#switch:{{{series}}}|TAP100|TAP200=|#default=by clicking the 'Edit' button next to a wireless device (<u>not an interface</u>)}} in the Network → {{#switch:{{{series}}}|TAP100|TAP200=Radio page.|#default=SSIDS page:}} |
| {{#switch:{{{name}}} | | {{#switch:{{{name}}} |
| |TAP100 = | | |TAP100 = |
Line 56: |
Line 56: |
| }} | | }} |
| | | |
− | =====General Setup===== | + | {{#switch:{{{series}}}|TAP100|TAP200= ====General Setup====|#default= =====General Setup=====}} |
− | ----
| + | |
| The <b>General Setup</b> section is used to turn a wireless device on or off, select the operating frequency (WiFi mode and channel), transmit power and define a country code. | | The <b>General Setup</b> section is used to turn a wireless device on or off, select the operating frequency (WiFi mode and channel), transmit power and define a country code. |
| | | |