Difference between revisions of "Template:Networking rutos manual leds"
From Teltonika Networks Wiki
(11 intermediate revisions by one other user not shown) | |||
Line 2: | Line 2: | ||
__TOC__ | __TOC__ | ||
==Power LED== | ==Power LED== | ||
− | {{#switch: {{{series}}} | OTD140 = The <b>power LED's</b> are located on the each Ethernet ports (POE In/POE Out). Green PD ( | + | {{#switch: {{{series}}} | OTD140 = The <b>power LED's</b> are located on the each Ethernet ports (POE In/POE Out). Green PD (power delivery) LED shines when power is supplied to device (POE In). Green PSE activity LED shines when PD device is connected to PoE out port (POE Out). |
| #default = The <b>power LED</b> is located on the bottom left corner of the front panel, just under the power connector.}} | | #default = The <b>power LED</b> is located on the bottom left corner of the front panel, just under the power connector.}} | ||
Line 150: | Line 150: | ||
<ul> | <ul> | ||
<li><span style="color: orange;"><b>Orange</b></span> - 10/100 Mbps connection</li> | <li><span style="color: orange;"><b>Orange</b></span> - 10/100 Mbps connection</li> | ||
− | <li><span style="color: green;"><b>Green</b></span> | + | <li><span style="color: green;"><b>Green</b></span> - 1000 Mbps connection</li> |
</ul> | </ul> | ||
Line 161: | Line 161: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>LED on</td> |
<td>A data connection on the port is operational (cable plugged in, end device visible, no data is being transferred).</td> | <td>A data connection on the port is operational (cable plugged in, end device visible, no data is being transferred).</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>LED off</td> |
− | <td>No data connection on the port is operational (no cable, bad cable or end device not visible for some other reason (such as damaged network card).</td> | + | <td>No data connection on the port is operational (no cable, bad cable or end device not visible for some other reason (such as damaged network card)).</td> |
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>LED blinking</td> |
<td>Connection established and data is being transferred over this port.</td> | <td>Connection established and data is being transferred over this port.</td> | ||
− | |||
− | |||
− | |||
− | |||
</tr> | </tr> | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
</table> | </table> | ||
| 3= There is one <b>LEDs</b> located at the top-left of each <b>Ethernet port</b> (top-right green port is unused). | | 3= There is one <b>LEDs</b> located at the top-left of each <b>Ethernet port</b> (top-right green port is unused). | ||
Line 216: | Line 204: | ||
</table> | </table> | ||
}}|}}{{#ifeq: {{{mobile}}} | 1 | <h2>Mobile network type LEDs</h2> | }}|}}{{#ifeq: {{{mobile}}} | 1 | <h2>Mobile network type LEDs</h2> | ||
− | {{#switch: {{{ | + | {{#switch: {{{series}}} | TRB2M = |
The <b>mobile network type LEDs</b> are located on left side of the back panel: | The <b>mobile network type LEDs</b> are located on left side of the back panel: | ||
Line 229: | Line 217: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G, NB and M1 LEDs are blinking at the same time</td> |
<td>No SIM or bad PIN</td> | <td>No SIM or bad PIN</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G, NB and M1 LEDs light up and down in sequence</td> |
<td>Searching mobile network operator</td> | <td>Searching mobile network operator</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G/NB/M1 LED blinking</td> |
<td>Gateway connected to 2G/NB/M1, no data session established</td> | <td>Gateway connected to 2G/NB/M1, no data session established</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G/NB/M1 LED turned ON</td> |
<td>Gateway connected to 2G/NB/M1 with data session</td> | <td>Gateway connected to 2G/NB/M1 with data session</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G/NB/M1 LED blinking</td> |
<td>Gateway connected to 2G/NB/M1 and data is being transferred</td> | <td>Gateway connected to 2G/NB/M1 and data is being transferred</td> | ||
</tr> | </tr> |
Revision as of 12:35, 9 January 2024
This page contains information the different types of LEDs and their behaviour on a {{{name}}} device.
Power LED
The power LED is located on the bottom left corner of the front panel, just under the power connector.
[[File:Networking_{{{name}}}_manual_leds_power_led.png|500px]]
It indicates whether the device is powered on or not.
State | Description |
---|---|
M LED turned on | Device is powered over the Main power connector. |
M LED turned off | Device is not powered over the Main power connector. |
R LED turned on | Device is powered over the Reserve power connector. |
R LED turned off | Device is not powered over the Reserve power connector. |
[[Category:{{{name}}} Manual]]