Difference between revisions of "Template:Networking rutos manual leds"
From Teltonika Networks Wiki
(16 intermediate revisions by 2 users not shown) | |||
Line 5: | Line 5: | ||
| #default = The <b>power LED</b> is located on the bottom left corner of the front panel, just under the power connector.}} | | #default = The <b>power LED</b> is located on the bottom left corner of the front panel, just under the power connector.}} | ||
− | [[File:Networking_{{lc:{{{name}}}}}_manual_leds_power_led.png|500px]] | + | {{#switch: {{{series}}} | RUTM = [[File:Networking_{{lc:{{{name}}}}}_manual_leds_power_led_v1.png|500px]] |
+ | | #default = [[File:Networking_{{lc:{{{name}}}}}_manual_leds_power_led.png|500px]]}} | ||
It indicates whether the device is powered on or not. | It indicates whether the device is powered on or not. | ||
Line 216: | Line 217: | ||
</table> | </table> | ||
}}|}}{{#ifeq: {{{mobile}}} | 1 | <h2>Mobile network type LEDs</h2> | }}|}}{{#ifeq: {{{mobile}}} | 1 | <h2>Mobile network type LEDs</h2> | ||
− | {{#switch: {{{ | + | {{#switch: {{{series}}} | TRB2M = |
The <b>mobile network type LEDs</b> are located on left side of the back panel: | The <b>mobile network type LEDs</b> are located on left side of the back panel: | ||
Line 229: | Line 230: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G, NB and M1 LEDs are blinking at the same time</td> |
<td>No SIM or bad PIN</td> | <td>No SIM or bad PIN</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G, NB and M1 LEDs light up and down in sequence</td> |
<td>Searching mobile network operator</td> | <td>Searching mobile network operator</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G/NB/M1 LED blinking</td> |
<td>Gateway connected to 2G/NB/M1, no data session established</td> | <td>Gateway connected to 2G/NB/M1, no data session established</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G/NB/M1 LED turned ON</td> |
<td>Gateway connected to 2G/NB/M1 with data session</td> | <td>Gateway connected to 2G/NB/M1 with data session</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> | + | <td>4G/NB/M1 LED blinking</td> |
<td>Gateway connected to 2G/NB/M1 and data is being transferred</td> | <td>Gateway connected to 2G/NB/M1 and data is being transferred</td> | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
</tr> | </tr> | ||
</table> | </table> | ||
Line 360: | Line 307: | ||
</tr> | </tr> | ||
</table>}} | </table>}} | ||
− | + | ||
− | + | ==Mobile signal strength indication LEDs== | |
{{#switch: {{{series}}} | TRB2M = | {{#switch: {{{series}}} | TRB2M = | ||
The <b>mobile signal strength indication LEDs</b> are located on left side of the back panel. | The <b>mobile signal strength indication LEDs</b> are located on left side of the back panel. | ||
Line 430: | Line 377: | ||
After releasing the button at one of the reset periods, all {{#ifeq: {{{name}}} | RUTX12 | {{#expr: {{{mobile_leds}}} * 2}} | {{{mobile_leds}}}}} LEDs will start blinking every 1 second. This signifies that the router <b>has begun the reset</b>. | After releasing the button at one of the reset periods, all {{#ifeq: {{{name}}} | RUTX12 | {{#expr: {{{mobile_leds}}} * 2}} | {{{mobile_leds}}}}} LEDs will start blinking every 1 second. This signifies that the router <b>has begun the reset</b>. | ||
− | | | + | |}} |
[[Category:{{{name}}} Manual]] | [[Category:{{{name}}} Manual]] |
Revision as of 16:59, 9 January 2024
This page contains information the different types of LEDs and their behaviour on a {{{name}}} device.
Power LED
The power LED is located on the bottom left corner of the front panel, just under the power connector.
[[File:Networking_{{{name}}}_manual_leds_power_led.png|500px]]
It indicates whether the device is powered on or not.
State | Description |
---|---|
M LED turned on | Device is powered over the Main power connector. |
M LED turned off | Device is not powered over the Main power connector. |
R LED turned on | Device is powered over the Reserve power connector. |
R LED turned off | Device is not powered over the Reserve power connector. |
[[Category:{{{name}}} Manual]]