Changes

no edit summary
Line 8: Line 8:  
}}
 
}}
   −
{{#ifeq: {{{series}}} | RUT9 |<i><b>Note</b>: <b>[[{{{name}}} RS232/RS485 (legacy WebUI)#RS232|click here]]</b> for the old style WebUI (FW version {{Template: Networking_device_manual_latest_fw | series = RUT9XX}} and earlier) user manual page.</i>|}}
+
{{#ifeq: {{{series}}}| RUT9 |<i><b>Note</b>: <b>[[{{{name}}} RS232/RS485 (legacy WebUI)#RS232|click here]]</b> for the old style WebUI (FW version {{Template: Networking_device_manual_latest_fw | series = RUT9XX}} and earlier) user manual page.</i>|}}
 
==Summary==
 
==Summary==
   Line 327: Line 327:  
</table>|}}
 
</table>|}}
   −
==Console==
+
{{#switch: {{{name}}} | TRB143 = | #default = ==Console==  
    
<b>Console</b> mode requires no further configuration than the settings above and is used as a direct-access method to the device's shell interface. For this purpose you may want use such applications as PuTTY on Windows and microcom, minicom, picocom or similar applications on Linux.
 
<b>Console</b> mode requires no further configuration than the settings above and is used as a direct-access method to the device's shell interface. For this purpose you may want use such applications as PuTTY on Windows and microcom, minicom, picocom or similar applications on Linux.
Line 395: Line 395:  
       <td>Turns Full Duplex mode on or off. This option is available only on the RS485 device.</td>
 
       <td>Turns Full Duplex mode on or off. This option is available only on the RS485 device.</td>
 
     </tr>|}}
 
     </tr>|}}
</table>
+
</table> }}
    
==Over IP==
 
==Over IP==
Line 425: Line 425:  
     <tr>
 
     <tr>
 
         <td>Device</td>
 
         <td>Device</td>
         <td>{{Template: Networking_rutos_manual_serial_ports | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}; default: <b>{{Template: Networking_rutos_manual_default_serial_port | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}</b></td>
+
         <td>{{#ifeq:{{{default}}}|mbus|MBUS| {{Template: Networking_rutos_manual_serial_ports | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}}}; default: <b>{{#ifeq:{{{default}}}|mbus|MBUS| {{Template: Networking_rutos_manual_default_serial_port | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}}}</b></td>
 
         <td>Specifies which serial port will be used for serial communication.</td>
 
         <td>Specifies which serial port will be used for serial communication.</td>
 
     </tr>
 
     </tr>
Line 440: Line 440:  
     <tr>
 
     <tr>
 
       <td>Stop bits</td>
 
       <td>Stop bits</td>
       <td>1 {{!}} 2; default: <b>1</b></td>
+
       <td>{{#switch: {{{name}}} | TRB143 = 1; default: <b>1</b>  | #default = 1 {{!}} 2; default: <b>1</b> }}</td>
 
       <td>Stop bits sent at the end of every character allow the receiving signal hardware to detect the end of a character and to resynchronise with the character stream. Electronic devices usually use one stop bit. Two stop bits are required if slow electromechanical devices are used.</td>
 
       <td>Stop bits sent at the end of every character allow the receiving signal hardware to detect the end of a character and to resynchronise with the character stream. Electronic devices usually use one stop bit. Two stop bits are required if slow electromechanical devices are used.</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>Parity</td>
 
     <td>Parity</td>
         <td>None {{!}} Odd {{!}} Even {{!}} Mark {{!}} Space; default: <b>None</b></td>
+
         <td>{{#switch: {{{name}}} | TRB143 = Even {{!}} default: Even | #default = None {{!}} Odd {{!}} Even {{!}} Mark {{!}} Space; default: <b>None</b> }}</td>
 
         <td>In serial transmission, parity is a method of detecting errors. An extra data bit is sent with each data character, arranged so that the number of 1 bits in each character, including the parity bit, is always odd or always even. If a byte is received with the wrong number of 1s, then it must have been corrupted. However, an even number of errors can pass the parity check.
 
         <td>In serial transmission, parity is a method of detecting errors. An extra data bit is sent with each data character, arranged so that the number of 1 bits in each character, including the parity bit, is always odd or always even. If a byte is received with the wrong number of 1s, then it must have been corrupted. However, an even number of errors can pass the parity check.
 
             <ul>
 
             <ul>
Line 522: Line 522:  
     </table>
 
     </table>
   −
[[File:Networking rutos manual serial utilities over ip mbus configuration security_v1.png|border|class=tlt-border]]
+
[[File:Networking rutos manual serial utilities over ip mbus configuration security_v2.png|border|class=tlt-border]]
    
<table class="nd-mantable">
 
<table class="nd-mantable">