Jump to content
  • EN

Fastboot for TRB1XX: Difference between revisions

← Older edit
VisualWikitext
MahmoudB (talk | contribs)
80 edits
No edit summary
MahmoudB (talk | contribs)
80 edits
No edit summary
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
==Introduction==
==Introduction==
'''Fastboot''' is a powerful protocol that allows for low-level management and modification of a router’s firmware and critical partitions. Fastboot mode provides direct access to the router’s storage, enabling advanced tasks such as flashing firmware, replacing the bootloader, and performing other critical updates. This article provides a guide on how to use Fastboot, specifically designed for the TRB1XX series.
'''Fastboot''' is a powerful protocol allowing low-level management and modification of a router’s firmware and critical partitions. Fastboot mode provides direct access to the router’s storage, enabling advanced tasks such as flashing firmware, replacing the bootloader, and performing other critical updates.
This article provides a guide on using Fastboot, specifically designed for the TRB1XX series.</li>


==Upgrade==
==Upgrade==


Firmware upgrade process via Fastboot requires only few simple steps:<br />
Firmware upgrade process via Fastboot requires only a few simple steps:


#Download the appropriate 2 files for TRB1_R_00.07.05.3: kernel (kernel.img) and rootfs (rootfs.ubi) These files need to be extracted according to the device's product code. can be downloaded from here: [https://kaunas.teltonika.lt:444/d/376f07e6f2b5495ebc4b/ kernel.img and rootfs -rootfs.ubi]
#<li>Download the necessary files for TRB1_R_00.07.05.3: kernel.img and rootfs.ubi. These files must be extracted according to the '''device's product code'''. You can download them from the following link: [https://kaunas.teltonika.lt:444/d/376f07e6f2b5495ebc4b/ '''kernel and rootfs'''].</li>
#Download and Install [https://kaunas.teltonika.lt:444/f/a9ffe2e9d98446f2aaf3/?dl=1 ADB software]
#<li>Download and install [https://kaunas.teltonika.lt:444/f/a9ffe2e9d98446f2aaf3/?dl=1 '''ADB software'''].[[File:11111.png|border|class=tlt-border]].</li>
[[File:11111.png|border|class=tlt-border]]
#<li>Press and hold the reset button, then simultaneously plug in the power cable while continuing to hold the reset button for approximately 5 seconds (until the mobile signal LEDs start blinking).</li>
 
#<li>Connect TRB14XX via USB cable to your computer.</li>
 
#<li>Open '''CMD''' with admin rights. Use the '''cd''' command to navigate to the directory where you saved the ''kernel.img'' and ''rootfs.ubi'' files (Example: '''cd C:\Test''').</li>
#Connect TRB14X via USB cable to your computer.
#<li>Then use this command: '''fastboot devices''' [[File:4444.png|border|class=tlt-border]].</li>
#Press and hold reset button, at the same time plug the power cable and keep holding reset button for about 5 seconds (mobile signal LED's should start blinking).
#*<li>If the device isn't listed, please use the [https://kaunas.teltonika.lt:444/d/40841368fece4a64a13e '''troubleshooting guide'''].</li>
#Place rootfs.ubi file in any easily accessible directory (e.g. in "C:\Test").
#<li>Flash the rootfs and kernel images by executing the following commands:</li>
#Open CMD ("Command Prompt" window) with administrator rights.
fastboot erase boot_a && fastboot erase boot_b && fastboot erase rootfs_a && fastboot erase rootfs_b && fastboot flash boot_a kernel.img && fastboot flash boot_b kernel.img && fastboot flash rootfs_a rootfs.ubi && fastboot flash rootfs_b rootfs.ubi
#Use cd command to navigate to the place where you saved the rootfs.ubi file (Example: '''cd C:\Test''').
[[File:6666.png|950px|border|class=tlt-border]]
#Then use this command: '''fastboot devices'''.
<li>After executing both commands, disconnect and reconnect the power to the TRB. The device should boot up normally, running firmware version TRB1_R_00.07.05.3.</li>
 
<li>You can install the latest firmware version on the TRB through the WebUI. The latest firmware can be downloaded from [https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads. '''here'''].</li>
if a device is not listed, use the following guide for troubleshooting: https://kaunas.teltonika.lt:444/d/40841368fece4a64a13e
 
#When it completes, use this command: fastboot flash rootfs_b build rootfs.ubi.
#When both commands are executed and finished running, unplug power from TRB and plug it again. It should boot up as normal.
#Install intermediate firmware version, which can be downloaded from here: https://wiki.teltonika-networks.com/view/TRB140_Legacy_FW_Upgrade_Instructions.
#Install desired firmware version to TRB through WebUI. Latest firmware can be downloaded from here: https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads.
 
 
See the details below for more information on each of these steps.
</big>
Retrieved from "https://wiki.teltonika-networks.com/view/Fastboot_for_TRB1XX"