Difference between revisions of "Template:Networking device manual sd card"
Gytispieze (talk | contribs) |
|||
(16 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
− | This chapter provides a description on how to correctly <b>insert a SD card</b> into a {{{name}}} device. | + | This chapter provides a description on how to correctly <b>insert a SD card</b> into a {{{name}}} device. |
− | {{Template: | + | {{Template: Networking_device_manual_fw_disclosure |
− | | fw_version ={{Template: | + | | series = {{{series}}} |
+ | | name = {{{name}}} | ||
+ | | fw_version ={{Template: Networking_device_manual_latest_fw | ||
| series = {{{series}}} | | series = {{{series}}} | ||
+ | | name = {{{name}}} | ||
}} | }} | ||
}} | }} | ||
Line 20: | Line 23: | ||
</ol> | </ol> | ||
[[File:Sd_card_measurments.png]] | [[File:Sd_card_measurments.png]] | ||
+ | {{#ifeq:{{{name}}}|RUT956| | ||
+ | ==={{{name}}} disclaimer=== | ||
+ | ---- | ||
+ | <span style="color:red"><b>Note: </b></span>Devices with micro SD card support have been in production starting from batch '''027'''. | ||
+ | |}} | ||
{{#ifeq:{{{name}}}|RUT955| | {{#ifeq:{{{name}}}|RUT955| | ||
==={{{name}}} disclaimer=== | ==={{{name}}} disclaimer=== | ||
Line 25: | Line 33: | ||
<span style="color:red"><b>Note: </b></span>Due to hardware limitations, {{{name}}} devices do not support firmware flashing while an SD card is inserted into the device. To successfully perform a firmware upgrade, it is required to remove the memory card first. Otherwise there is a high risk of data and configuration loss. | <span style="color:red"><b>Note: </b></span>Due to hardware limitations, {{{name}}} devices do not support firmware flashing while an SD card is inserted into the device. To successfully perform a firmware upgrade, it is required to remove the memory card first. Otherwise there is a high risk of data and configuration loss. | ||
|}} | |}} | ||
− | |||
==Installation== | ==Installation== | ||
Line 63: | Line 70: | ||
<table> | <table> | ||
<tr> | <tr> | ||
− | <td>[[File: | + | <td> |
+ | [[File:Networking_{{{name}}}_manual_sd_card.png|right|300px]] | ||
+ | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
Line 103: | Line 112: | ||
---- | ---- | ||
<ol> | <ol> | ||
− | <li>Connect to device's '''[[{{{name}}} | + | <li>Connect to device's '''[[{{{name}}}_Maintenance#CLI | CLI]]'''.</li> |
<li>Use command <code>ls /dev/ | grep mmc</code> to display recognized memory cards:</li> | <li>Use command <code>ls /dev/ | grep mmc</code> to display recognized memory cards:</li> | ||
<code>root@Teltonika-{{{name}}}:~# ls /dev/ | grep mmc</br> | <code>root@Teltonika-{{{name}}}:~# ls /dev/ | grep mmc</br> |
Latest revision as of 11:21, 11 September 2024
This chapter provides a description on how to correctly insert a SD card into a {{{name}}} device.
The information in this page is updated in accordance with firmware version .
Compatibility
Before installation, make sure your SD card is compatible with {{{name}}} devices:
- Maximum supported (tested) SD card capacity is 64GB.
- Supported (tested) formats are: FAT32, NTFS, ext2, ext3, ext4.
- SD cards with a fixed 1.8V voltage are not supported. Make sure your memory card supports 3.3V by referring to manufacturer's documentation.
- The device is compatible only with microSD size memory cards.
Installation
Make sure device is powered off before inserting SD card!
|
|
Results
Once device is booted up with an SD card installed, you can confirm it is recognized by navigating to [[{{{name}}}_USB_Tools#Mounted_File_Systems | USB Tools]] WebUI page. Under Mounted File Systems the SD card should be visible:
You may now use various functionality found in [[{{{name}}}_USB_Tools | USB Tools]] with the SD card instead of a USB device.
If you are having trouble with the device recognizing your SD card, please refer to the Troubleshooting section below.
Troubleshooting
- Double check the SD card is [[{{{name}}}_SD_Card#Compatibility | compatible]] with {{{name}}} devices.
- Make sure the SD card is not corrupted. We recommend formatting it before first installation.
Formatting SD card using device
If you are unable to format the memory card using other means, it is possible to do it directly on {{{name}}} device.
Pre-requisites
- Device must have WAN access.
- SD card must be recognized by the filesystem.
Procedure
- Connect to device's [[{{{name}}}_Maintenance#CLI | CLI]].
- Use command
ls /dev/ | grep mmc
to display recognized memory cards: - Once confirmed the SD is recognized, we may start the formatting procedure:
- Run commands
opkg update
andopkg install e2fsprogs
to download required tools. - Unmount the SD card with command
umount /dev/mmcblk0p1
- Start formatting with command
mkfs.extX /dev/mmcblk0p1
where X is either 2 (for ext2 format), 3 (for ext3 format) or 4 (for ext4 format). - A successful format procedure should look like this:
- Reboot the {{{name}}} device and refer to [[{{{name}}}_SD_Card#Results | Results]] section
root@Teltonika-{{{name}}}:~# ls /dev/ | grep mmc
mmcblk0
mmcblk0p1 ← SD card
root@Teltonika-RUT955:~# mkfs.ext2 /dev/mmcblk0p1
mke2fs 1.45.6 (20-Mar-2020)
/dev/mmcblk0p1 contains a ntfs file system labelled '64gb'
Proceed anyway? (y,N) y
Creating filesystem with 15132670 4k blocks and 3784704 inodes
Filesystem UUID: 6053673b-d6b0-420d-84da-0669b71a5211
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000, 7962624, 11239424
Allocating group tables: done
Writing inode tables: done
Writing superblocks and filesystem accounting information: done
Note: The Writing inode tables section might take a long time depending on the size of your SD card (10+ minutes with 64GB SD).
[[Category:{{{name}}} Manual]]