Template:Networking rutos manual leds: Difference between revisions
No edit summary Tag: Reverted |
No edit summary |
||
| (9 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
__TOC__ | __TOC__ | ||
==Power LED== | ==Power LED== | ||
{{#switch: {{{series}}} | OTD140 = The <b>power LED's</b> are located on the each Ethernet ports (POE In/POE Out). Green PD (Power Device) LED shines when power is supplied to device '''PoE In''' port. Green PSE (Power Sourcing Equipment) activity LED shines when PD device is connected to '''PoE Out''' port. | {{#switch: {{{series}}} | OTD140 | OTD500 = The <b>power LED's</b> are located on the each Ethernet ports (POE In/POE Out). Green PD (Power Device) LED shines when power is supplied to device '''PoE In''' port. Green PSE (Power Sourcing Equipment) activity LED shines when PD device is connected to '''PoE Out''' port. | ||
| #default = The <b>power LED</b> is located on the bottom left corner of the front panel, just under the power connector.}} | | #default = The <b>power LED</b> is located on the bottom left corner of the front panel, just under the power connector.}} | ||
| Line 8: | Line 8: | ||
It indicates whether the device is powered on or not. | It indicates whether the device is powered on or not. | ||
{{# | {{#switch: {{{name}}} | OTD140 | OTD500 = | #default = | ||
<table class="nd-othertables_3"> | <table class="nd-othertables_3"> | ||
<tr> | <tr> | ||
| Line 116: | Line 116: | ||
{{#switch: {{{eth_leds}}} | {{#switch: {{{eth_leds}}} | ||
| 1 =The <b>Ethernet port LEDs</b> are located on the device's front panel, under each respective Ethernet port. | | 1 = The <b>Ethernet port LEDs</b> are located on the device's front panel, under each respective Ethernet port. | ||
[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]] | [[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]] | ||
| Line 142: | Line 142: | ||
</tr>--> | </tr>--> | ||
</table> | </table> | ||
| 2=There are two <b>LEDs</b> located at the top of each <b>Ethernet port</b>. | | 2 = There are two <b>LEDs</b> located at the top of each <b>Ethernet port</b>. | ||
[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]] | [[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]] | ||
| Line 304: | Line 304: | ||
</table> | </table> | ||
| TRM200 = | | TRM200 = | ||
The <b>mobile network type LED</b> is located on | The <b>mobile network type LED</b> is located on right side of the front panel: | ||
[[File:Networking_{{lc:{{{name}}}}}_manual_leds_mobile_network_type_leds.png|500px]] | [[File:Networking_{{lc:{{{name}}}}}_manual_leds_mobile_network_type_leds.png|500px]] | ||
| Line 337: | Line 337: | ||
</table> | </table> | ||
The <b>LTE LED</b> is located on | The <b>LTE LED</b> is located on right side of the front panel: | ||
[[File:Networking_{{lc:{{{name}}}}}_manual_leds_mobile_lte.png|500px]] | [[File:Networking_{{lc:{{{name}}}}}_manual_leds_mobile_lte.png|500px]] | ||
| Line 556: | Line 556: | ||
The Mobile signal strength LEDs can also be used as a <b>time indicator for holding the reset button</b>. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a <b>User's default configuration reset</b> and 12 seconds (by default) to initiate a <b>Factory reset</b>. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a <b>Factory reset</b>. If the button was held down longer than 20 seconds (by default) no action will be taken. | The Mobile signal strength LEDs can also be used as a <b>time indicator for holding the reset button</b>. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a <b>User's default configuration reset</b> and 12 seconds (by default) to initiate a <b>Factory reset</b>. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a <b>Factory reset</b>. If the button was held down longer than 20 seconds (by default) no action will be taken. | ||
While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with <b>{{{name}}}</b>, when all {{# | While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with <b>{{{name}}}</b>, when all {{#switch: {{{name}}} | RUTX12 | RUTM52 = {{#expr: {{{mobile_leds}}} * 2}} | #default = {{{mobile_leds}}}}} Mobile signal strength LEDs are lit up, they represent that {{#switch: {{{name}}} | RUTX12 | RUTM52 = {{#expr: {{{mobile_leds}}} * 4}} | #default = {{#expr: {{{mobile_leds}}} * 2}}}} (LED number multiplied by 2) seconds have passed since you pressed down on the reset button. | ||
After releasing the button at one of the reset periods, all {{# | After releasing the button at one of the reset periods, all {{#switch: {{{name}}} | RUTX12 | RUTM52 = {{#expr: {{{mobile_leds}}} * 2}} | #default = {{{mobile_leds}}}}} LEDs will start blinking every 1 second. This signifies that the router <b>has begun the reset</b>. | ||
}}|}} | |||
[[Category:{{{name}}} Manual]] | [[Category:{{{name}}} Manual]] | ||
Latest revision as of 11:14, 14 November 2024
This page contains information the different types of LEDs and their behaviour on a {{{name}}} device.
Power LED
The power LED is located on the bottom left corner of the front panel, just under the power connector.
[[File:Networking_{{{name}}}_manual_leds_power_led.png|500px]]
It indicates whether the device is powered on or not.
| State | Description |
|---|---|
| M LED turned on | Device is powered over the Main power connector. |
| M LED turned off | Device is not powered over the Main power connector. |
| R LED turned on | Device is powered over the Reserve power connector. |
| R LED turned off | Device is not powered over the Reserve power connector. |
[[Category:{{{name}}} Manual]]