Template:Networking rutos manual serial utilities: Difference between revisions
No edit summary |
No edit summary |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 25: | Line 25: | ||
====Connector pinout==== | ====Connector pinout==== | ||
---- | ---- | ||
The | The following table lists commonly used RS-232 signals ('''DTE male''' to '''DCE female'''). The RS232 connector type on device is a DCE female. | ||
[[File: | [[File:Services_rs232_connector_v1.png|400px]] | ||
<table class="nd-othertables"> | <table class="nd-othertables"> | ||
| Line 40: | Line 40: | ||
<td>DCD</td> | <td>DCD</td> | ||
<td>Data Carrier Detect</td> | <td>Data Carrier Detect</td> | ||
<td> | <td>Input</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 46: | Line 46: | ||
<td>RXD</td> | <td>RXD</td> | ||
<td>Receive Data</td> | <td>Receive Data</td> | ||
<td> | <td>Input</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 52: | Line 52: | ||
<td>TXD</td> | <td>TXD</td> | ||
<td>Transmit Data</td> | <td>Transmit Data</td> | ||
<td> | <td>Output</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 58: | Line 58: | ||
<td>DTR</td> | <td>DTR</td> | ||
<td>Data Terminal Ready</td> | <td>Data Terminal Ready</td> | ||
<td> | <td>Output</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 70: | Line 70: | ||
<td>DSR</td> | <td>DSR</td> | ||
<td>Data Set Ready</td> | <td>Data Set Ready</td> | ||
<td> | <td>Input</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 76: | Line 76: | ||
<td>RTS</td> | <td>RTS</td> | ||
<td>Ready To Send</td> | <td>Ready To Send</td> | ||
<td> | <td>Output</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 82: | Line 82: | ||
<td>CTS</td> | <td>CTS</td> | ||
<td>Clear To Send</td> | <td>Clear To Send</td> | ||
<td> | <td>Input</td> | ||
</tr>{{#ifeq:{{{series}}}|TRB1| | </tr>{{#ifeq:{{{series}}}|TRB1| | ||
<tr> | <tr> | ||
| Line 88: | Line 88: | ||
<td>RI</td> | <td>RI</td> | ||
<td>Ring Indicator</td> | <td>Ring Indicator</td> | ||
<td> | <td>Input (connected to +3.8V permanently via a 4.7k resistor) </td> | ||
</tr>| | </tr>| | ||
<tr> | <tr> | ||
| Line 94: | Line 94: | ||
<td>RI</td> | <td>RI</td> | ||
<td>Ring Indicator</td> | <td>Ring Indicator</td> | ||
<td> | <td>Input (connected to +5V permanently via a 4.7k resistor) </td> | ||
</tr>}} | </tr>}} | ||
</table> | </table> | ||
| Line 335: | Line 335: | ||
===Advanced settings=== | ===Advanced settings=== | ||
{{#switch: {{{name}}} | TRB142 | TRB145 = | |||
[[File:Networking_rutos_manual_serial_utilities_modem_control_advanced_settings.png|border|class=tlt-border]] | [[File:Networking_rutos_manual_serial_utilities_modem_control_advanced_settings_trb.png|border|class=tlt-border]] | ||
| #default = [[File:Networking_rutos_manual_serial_utilities_modem_control_advanced_settings.png|border|class=tlt-border]]}} | |||
<table class="nd-mantable"> | <table class="nd-mantable"> | ||
| Line 348: | Line 349: | ||
<td>string; default: <b>none</b></td> | <td>string; default: <b>none</b></td> | ||
<td>Prints message to serial device when modem control is ready.</td> | <td>Prints message to serial device when modem control is ready.</td> | ||
</tr> | </tr>{{#switch: {{{name}}} | TRB142 | TRB145 = | ||
<tr> | |||
<td>Data mode</td> | |||
<td>off {{!}} on; default: <b>off</b></td> | |||
<td>Enable this option to allow data mode. Data mode will not operate without it.</td> | |||
</tr>| #default =}} | |||
<tr> | <tr> | ||
<td>Canonical mode</td> | <td>Canonical mode</td> | ||