BAT120 LEDs: Difference between revisions
Gytispieze (talk | contribs) (Created page with "This wiki page contains information about BAT120 <b>LEDs</b> and their actions. __TOC__ ==Power IN LED== The <b>IN PWR LED</b> is the left-most located LED on the front pan...") |
No edit summary |
||
| (One intermediate revision by one other user not shown) | |||
| Line 15: | Line 15: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>LED turned ON</td> | <td>LED turned ON green</td> | ||
<td>PSU connected to IN PWR socket</td> | <td>PSU connected to IN PWR socket</td> | ||
</tr> | </tr> | ||
<tr> | |||
<td>LED turned ON red</td> | |||
<td>PSU connected to IN PWR socket, charge failure /Vin too low</td> | |||
</table> | </table> | ||
| Line 25: | Line 28: | ||
[[File:Network_bat_manual_bat120_pwrout_led_v1.png|400px]] | [[File:Network_bat_manual_bat120_pwrout_led_v1.png|400px]] | ||
<br> | |||
'''''Note:''' OUT PWR LED will illuminate green when connected load is greater than 0.5W. If the power consumed by an external device is less than 0.5W, it will still be powered, but OUT PWR LED will stay off.'' | |||
<table class="nd-othertables_2"> | <table class="nd-othertables_2"> | ||
<tr> | <tr> | ||
| Line 32: | Line 36: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>LED turned ON</td> | <td>LED turned ON green</td> | ||
<td>OUT PWR socket connected to the device</td> | <td>OUT PWR socket connected to the device and external device is being powered</td> | ||
</tr> | </tr> | ||
<tr> | |||
<td>LED turned ON red</td> | |||
<td> If the OUTPUT is shorted (requiring a reset) or the BAT120 has overheated (no reset needed), the OUT PWR LED will turn red, signifying an issue that needs attention. </td> | |||
</tr> | |||
</table> | </table> | ||
| Line 64: | Line 73: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td> | <td>Power LEDs blink every 5 seconds</td> | ||
<td>BAT120 is charging.</td> | <td>BAT120 is charging.</td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
Latest revision as of 10:02, 18 December 2024
Main Page > BAT Uninterruptable Power Supplies > BAT120 > BAT120 Manual > BAT120 LEDsThis wiki page contains information about BAT120 LEDs and their actions.
Power IN LED
The IN PWR LED is the left-most located LED on the front panel:
| Action | Description |
|---|---|
| LED turned ON green | PSU connected to IN PWR socket |
| LED turned ON red | PSU connected to IN PWR socket, charge failure /Vin too low |
Power OUT LED
The OUT PWR LED is the second from the left LED located on the front panel:
Note: OUT PWR LED will illuminate green when connected load is greater than 0.5W. If the power consumed by an external device is less than 0.5W, it will still be powered, but OUT PWR LED will stay off.
| Action | Description |
|---|---|
| LED turned ON green | OUT PWR socket connected to the device and external device is being powered |
| LED turned ON red | If the OUTPUT is shorted (requiring a reset) or the BAT120 has overheated (no reset needed), the OUT PWR LED will turn red, signifying an issue that needs attention. |
Power LEDs
The Power LEDs are located in the middle of the front panel:
| Action | Description |
|---|---|
| LED turned ON | Shows BAT120 state of charge. Each LED equals to 25% of SOC. |
Combined LED states
Some of the states are shown with multiple LEDs:
| Action | Description |
|---|---|
| Power LEDs blink every 5 seconds | BAT120 is charging. |