Line 18: |
Line 18: |
| <tr> | | <tr> |
| <td>Routing table</td> | | <td>Routing table</td> |
− | <td>Main {{!}} WAN {{!}} WAN2 {{!}} WAN3; Default: '''WAN'''</td> | + | <td>Main | WAN | WAN2 | WAN3; Default: '''WAN'''</td> |
| <td>Defines which table will be used for the route in question</td> | | <td>Defines which table will be used for the route in question</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Interface</td> | | <td>Interface</td> |
− | <td>LAN {{!}} WAN(wired) {{!}} WAN2(Mobile) {{!}} WAN3(WiFi) {{!}} VPN instances; Default: '''WAN(wired)'''</td> | + | <td>LAN | WAN(wired) | WAN2(Mobile) | WAN3(WiFi) | VPN instances; Default: '''WAN(wired)'''</td> |
| <td>The zone where the target network resides</td> | | <td>The zone where the target network resides</td> |
| </tr> | | </tr> |
Line 110: |
Line 110: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles the BGP protocol ON or OFF</td> | | <td>Toggles the BGP protocol ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable vty</td> | | <td>Enable vty</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles vty access from LAN ON or OFF</td> | | <td>Toggles vty access from LAN ON or OFF</td> |
| </tr> | | </tr> |
Line 138: |
Line 138: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles the BGP instance ON or OFF</td> | | <td>Toggles the BGP instance ON or OFF</td> |
| </tr> | | </tr> |
Line 171: |
Line 171: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles the BGP peer ON or OFF</td> | | <td>Toggles the BGP peer ON or OFF</td> |
| </tr> | | </tr> |
Line 199: |
Line 199: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles the Access filter ON or OFF</td> | | <td>Toggles the Access filter ON or OFF</td> |
| </tr> | | </tr> |
Line 209: |
Line 209: |
| <tr> | | <tr> |
| <td>Action</td> | | <td>Action</td> |
− | <td>Permit {{!}} Deny; Default: '''Permit'''</td> | + | <td>Permit | Deny; Default: '''Permit'''</td> |
| <td>Denies or permits matched entry</td> | | <td>Denies or permits matched entry</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Network</td> | | <td>Network</td> |
− | <td>Any {{!}} ip; Default: '''Any'''</td> | + | <td>Any | ip; Default: '''Any'''</td> |
| <td>Applies filter rule for this source network</td> | | <td>Applies filter rule for this source network</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Direction</td> | | <td>Direction</td> |
− | <td>Inbound {{!}} Outbound; Default: '''Inbound'''</td> | + | <td>Inbound | Outbound; Default: '''Inbound'''</td> |
| <td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td> | | <td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td> |
| </tr> | | </tr> |
Line 241: |
Line 241: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles RIP Protocol ON or OFF</td> | | <td>Toggles RIP Protocol ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable vty</td> | | <td>Enable vty</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles vty access from LAN ON or OFF</td> | | <td>Toggles vty access from LAN ON or OFF</td> |
| </tr> | | </tr> |
Line 256: |
Line 256: |
| <tr> | | <tr> |
| <td>Version</td> | | <td>Version</td> |
− | <td>2 {{!}} 1; Default: '''2'''</td> | + | <td>2 | 1; Default: '''2'''</td> |
| <td>Specifies the version of RIP</td> | | <td>Specifies the version of RIP</td> |
| </tr> | | </tr> |
Line 279: |
Line 279: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles RIP Interface ON or OFF</td> | | <td>Toggles RIP Interface ON or OFF</td> |
| </tr> | | </tr> |
Line 289: |
Line 289: |
| <tr> | | <tr> |
| <td>Passive interface</td> | | <td>Passive interface</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Sets the specified interface to passive mode. On passive mode interface, all receiving packets are processed as normal and ripd does not send either multicast or unicast RIP packets</td> | | <td>Sets the specified interface to passive mode. On passive mode interface, all receiving packets are processed as normal and ripd does not send either multicast or unicast RIP packets</td> |
| </tr> | | </tr> |
Line 307: |
Line 307: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles the Access filter ON or OFF</td> | | <td>Toggles the Access filter ON or OFF</td> |
| </tr> | | </tr> |
Line 317: |
Line 317: |
| <tr> | | <tr> |
| <td>Action</td> | | <td>Action</td> |
− | <td>Permit {{!}} Deny; Default: '''Permit'''</td> | + | <td>Permit | Deny; Default: '''Permit'''</td> |
| <td>Denies or permits matched entry</td> | | <td>Denies or permits matched entry</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Network</td> | | <td>Network</td> |
− | <td>Any {{!}} ip; Default: '''Any'''</td> | + | <td>Any | ip; Default: '''Any'''</td> |
| <td>Applies filter rule for this source network</td> | | <td>Applies filter rule for this source network</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Direction</td> | | <td>Direction</td> |
− | <td>Inbound {{!}} Outbound; Default: '''Inbound'''</td> | + | <td>Inbound | Outbound; Default: '''Inbound'''</td> |
| <td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td> | | <td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td> |
| </tr> | | </tr> |
Line 348: |
Line 348: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles OSPF Protocol ON or OFF</td> | | <td>Toggles OSPF Protocol ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable vty</td> | | <td>Enable vty</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles vty access from LAN ON or OFF</td> | | <td>Toggles vty access from LAN ON or OFF</td> |
| </tr> | | </tr> |
Line 380: |
Line 380: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles OSPF interface ON or OFF</td> | | <td>Toggles OSPF interface ON or OFF</td> |
| </tr> | | </tr> |
Line 410: |
Line 410: |
| <tr> | | <tr> |
| <td>Type</td> | | <td>Type</td> |
− | <td>Broadcast {{!}} Nonbroadcast {{!}} Point-to-point {{!}} Point-to-multipoint; Default: " "</td> | + | <td>Broadcast | Nonbroadcast | Point-to-point | Point-to-multipoint; Default: " "</td> |
| <td>Set explicit network type for the specified interface</td> | | <td>Set explicit network type for the specified interface</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Authentication</td> | | <td>Authentication</td> |
− | <td>None {{!}} Password {{!}} MD5 HMAC; Default: " "</td> | + | <td>None | Password | MD5 HMAC; Default: " "</td> |
| <td>Specifies the authentication mode that should be used for the interface</td> | | <td>Specifies the authentication mode that should be used for the interface</td> |
| </tr> | | </tr> |
Line 433: |
Line 433: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles OSPF area ON or OFF</td> | | <td>Toggles OSPF area ON or OFF</td> |
| </tr> | | </tr> |
Line 456: |
Line 456: |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes {{!}} no; Default: '''no'''</td> | + | <td>yes | no; Default: '''no'''</td> |
| <td>Toggles OSPF network ON or OFF</td> | | <td>Toggles OSPF network ON or OFF</td> |
| </tr> | | </tr> |
Line 470: |
Line 470: |
| </tr> | | </tr> |
| </table> | | </table> |
| + | |
| + | [[Category:RUT950 WebUI]] |