Difference between revisions of "Template:Networking rut955 manual modbus modbus tcp set parameters table"
From Teltonika Networks Wiki
Gytispieze (talk | contribs) |
|||
(11 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
<table class="nd-othertables"> | <table class="nd-othertables"> | ||
<tr> | <tr> | ||
− | <th width=" | + | <th width="350">value to set</th> |
− | <th width=" | + | <th width="180">register address</th> |
− | |||
<th width="150">register value</th> | <th width="150">register value</th> | ||
<th width="466">description</th> | <th width="466">description</th> | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Digital output 1 (DOUT1) (ON/OFF<span class="asterisk">*</span>)</td> | <td>Digital output 1 (DOUT1) (ON/OFF<span class="asterisk">*</span>)</td> | ||
<td>201</td> | <td>201</td> | ||
− | + | <td>1 | 0</td> | |
− | <td>1 | ||
<td>Changes the state of the open collector (OC) output</td> | <td>Changes the state of the open collector (OC) output</td> | ||
</tr> | </tr> | ||
Line 31: | Line 15: | ||
<td>Digital output 2 (DOUT2) (ON/OFF<span class="asterisk">*</span>)</td> | <td>Digital output 2 (DOUT2) (ON/OFF<span class="asterisk">*</span>)</td> | ||
<td>202</td> | <td>202</td> | ||
− | + | <td>1 | 0</td> | |
− | <td>1 | ||
<td>Changes the state of the relay output</td> | <td>Changes the state of the relay output</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Switch WiFi (ON/OFF<span class="asterisk">*</span>)</td> | <td>Switch WiFi (ON/OFF<span class="asterisk">*</span>)</td> | ||
− | <td> | + | <td>210</td> |
− | |||
<td>1 | 0</td> | <td>1 | 0</td> | ||
<td>Turns WiFi ON or OFF</td> | <td>Turns WiFi ON or OFF</td> | ||
Line 44: | Line 26: | ||
<tr> | <tr> | ||
<td>Switch mobile data connection (ON/OFF<span class="asterisk">*</span>)</td> | <td>Switch mobile data connection (ON/OFF<span class="asterisk">*</span>)</td> | ||
− | <td> | + | <td>211</td> |
− | |||
<td>1 | 0</td> | <td>1 | 0</td> | ||
<td>Turns mobile data connection ON or OFF</td> | <td>Turns mobile data connection ON or OFF</td> | ||
Line 51: | Line 32: | ||
<tr> | <tr> | ||
<td>Switch SIM card</td> | <td>Switch SIM card</td> | ||
− | <td> | + | <td>212</td> |
− | |||
<td>1 | 2 | 0</td> | <td>1 | 2 | 0</td> | ||
<td>Changes the active SIM card slot | <td>Changes the active SIM card slot | ||
Line 61: | Line 41: | ||
</ul> | </ul> | ||
</td> | </td> | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Change APN</td> | <td>Change APN</td> | ||
− | <td> | + | <td>213</td> |
− | |||
<td>APN code</td> | <td>APN code</td> | ||
<td>Changes APN. <br> The number of input registers may vary depending on the length of the APN, but the very first byte of the set APN command denotes the number of the SIM card for which to set the APN. This byte should be set to: | <td>Changes APN. <br> The number of input registers may vary depending on the length of the APN, but the very first byte of the set APN command denotes the number of the SIM card for which to set the APN. This byte should be set to: | ||
Line 82: | Line 54: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | + | <td>Reboot</td> | |
− | + | <td>220</td> | |
− | + | <td>1</td> | |
− | + | <td>Reboots the router</td> | |
− | <td> | ||
</tr> | </tr> | ||
</table> | </table> |
Revision as of 14:20, 18 July 2019
value to set | register address | register value | description |
---|---|---|---|
Digital output 1 (DOUT1) (ON/OFF*) | 201 | 1 | 0 | Changes the state of the open collector (OC) output |
Digital output 2 (DOUT2) (ON/OFF*) | 202 | 1 | 0 | Changes the state of the relay output |
Switch WiFi (ON/OFF*) | 210 | 1 | 0 | Turns WiFi ON or OFF |
Switch mobile data connection (ON/OFF*) | 211 | 1 | 0 | Turns mobile data connection ON or OFF |
Switch SIM card | 212 | 1 | 2 | 0 | Changes the active SIM card slot
|
Change APN | 213 | APN code | Changes APN. The number of input registers may vary depending on the length of the APN, but the very first byte of the set APN command denotes the number of the SIM card for which to set the APN. This byte should be set to:
|
Reboot | 220 | 1 | Reboots the router |