Difference between revisions of "Status Control Commands"
| (2 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| + | __TOC__ | ||
| + | |||
== Status Control Commands == | == Status Control Commands == | ||
| − | + | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=38 '''4.1. AT+CPAS Mobile Equipment Activity Status - page 37'''] | |
| + | |||
TheExecutionCommand queries the module‟s activity status. | TheExecutionCommand queries the module‟s activity status. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=39 '''4.2. AT+CEER Extended Error Report - page 38'''] | |
| − | + | ||
The commandis used to query an extended error and report the cause of the last failed operation, such as: | The commandis used to query an extended error and report the cause of the last failed operation, such as: | ||
* the failure to release a call; | * the failure to release a call; | ||
| Line 14: | Line 17: | ||
* the failureto attach GPRS or the failureto activatea PDP context; | * the failureto attach GPRS or the failureto activatea PDP context; | ||
* the failureto detach GPRS or the failureto deactivate a PDP context. | * the failureto detach GPRS or the failureto deactivate a PDP context. | ||
| + | The release cause <text> is a text to describe the cause information given by the network. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=40 '''4.3. AT+QCFG Extended Configuration Settings - page 39'''] | |
| − | |||
| − | |||
The command is used to query and configure various settings of UE. | The command is used to query and configure various settings of UE. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=41 '''4.3.1. AT+QCFG="gprsattach" GPRS Attach Mode Configuration - page 40'''] | |
| − | + | ||
The command specifies the mode to attach GPRS when UE is powered on. This configuration is valid only after the module is restarted. | The command specifies the mode to attach GPRS when UE is powered on. This configuration is valid only after the module is restarted. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=42 '''4.3.2. AT+QCFG="nwscanmode" Network Search Mode Configuration - page 41'''] | |
| − | + | ||
| − | The commands pecifies the network mode to be serached. If | + | The commands pecifies the network mode to be serached. If <effect>is omitted, the configuration will take effect immediately. |
| + | |||
| + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=43 '''4.3.3. AT+QCFG="nwscanseq" Network Searching Sequence Configuration - page 42'''] | ||
| − | |||
| − | |||
The command specifies the sequence of searching network. This configuration is valid only after the module is restarted. | The command specifies the sequence of searching network. This configuration is valid only after the module is restarted. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=44 '''4.3.4. AT+QCFG="roamservice" Roam Service Configuration - page 43'''] | |
| − | + | ||
| − | The command is used to enable or disable the roam service. If '''<effect> | + | The command is used to enable or disable the roam service. If <effect>is omitted, the configuration will take effect immediately. |
| + | |||
| + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=44 '''4.3.5. AT+QCFG="servicedomain" Service Domain Configuration - page 43'''] | ||
| + | |||
| + | The command specifies the registered service domain. If <effect>is omitted, the configuration will take effect immediately. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=45 '''4.3.6. AT+QCFG="band" Band Configuration - page 44'''] | |
| − | - | ||
| − | |||
| − | + | The command specifies the preferred frequency bands to be searched of UE. If <effect>is omitted, the configuration will take effect immediately. | |
| − | - | + | |
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=47 '''4.3.7. AT+QCFG="hsdpacat" HSDPA Category Configuration - page 46'''] | |
| − | |||
| − | |||
The command specifies the HSDPA category. This configuration is valid only after the module is restarted. | The command specifies the HSDPA category. This configuration is valid only after the module is restarted. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=47 '''4.3.8. AT+QCFG="hsupacat" HSUPA Category Configuration - page 46'''] | |
| − | + | ||
The command specifies the HSUPA category. This configuration is valid only after the module is restarted. | The command specifies the HSUPA category. This configuration is valid only after the module is restarted. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=48 '''4.3.9. AT+QCFG="rrc" RRC Release Version Configuration - page 47'''] | |
| − | + | ||
The command specifies the RRC release version. This configuration is valid only after the module is restarted. | The command specifies the RRC release version. This configuration is valid only after the module is restarted. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=49 '''4.3.10. AT+QCFG="sgsn" UE SGSN Release Version Configuration - page 48'''] | |
| − | + | ||
The command specifies the UE SGSN release version. This configuration is valid only after the module is restarted. | The command specifies the UE SGSN release version. This configuration is valid only after the module is restarted. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=49 '''4.3.11. AT+QCFG="msc" UE MSC Release Version Configuration - page 48'''] | |
| − | + | ||
The commandspecifies the UE MSCrelease version. This configuration is valid only after the module is restarted. | The commandspecifies the UE MSCrelease version. This configuration is valid only after the module is restarted. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=50 '''4.3.12. AT+QCFG="PDP/duplicatechk"Establish Multi PDNs with the Same APN - page 49'''] | |
| − | + | ||
The command allows/refuses establishing multi PDNs with the same APN profile. The configuration will take effect immediately. | The command allows/refuses establishing multi PDNs with the same APN profile. The configuration will take effect immediately. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=51 '''4.3.13. AT+QCFG="urc/ri/ring" RI Behavior When RING URC is Presented - page 50'''] | |
| − | - | ||
| − | ''' | ||
| − | + | AT+QCFG="urc/ri/ring", AT+QCFG="urc/ri/smsincoming" and AT+QCFG="urc/ri/other"control the RI (ring indicator) behavior when a URC is reported. These configurations will be stored into NV automatically. The ring indicator is active low. AT+QCFG="urc/ri/ring" specifies the RI behavior when URC RING is presented to indicate an incoming call. | |
| − | |||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=53 '''4.3.14. AT+QCFG="urc/ri/smsincoming" RIBehavior WhenIncoming SMSURCs are Presented - page 52'''] | |
| − | + | ||
| − | The command specifies the RI (ring indicator) behavior when related incoming message URCs are presented. Related incoming message URCs list: | + | The command specifies the RI (ring indicator) behavior when related incoming message URCs are presented. Related incoming message URCs list: +CMTI,+CMT,+CDSand+CBM. |
| + | |||
| + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=54 '''4.3.15. AT+QCFG="urc/ri/other" RI Behavior When Other URCsare Presented - page 53'''] | ||
| − | |||
| − | |||
The command specifies the RI (ring indicator)behavior when other URCs are presented. | The command specifies the RI (ring indicator)behavior when other URCs are presented. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=54 '''4.3.16. AT+QCFG="risignaltype" RISignal Output Carrier - page 53'''] | |
| − | + | ||
The command specifies the RI (ring indicator) signal output carrier. | The command specifies the RI (ring indicator) signal output carrier. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=55 '''4.3.17. AT+QCFG="urc/delay"Delay URC Indication - page 54'''] | |
| − | + | ||
The commandcan delay the output ofURC indication until ring indicatorpulse ends. | The commandcan delay the output ofURC indication until ring indicatorpulse ends. | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=56 '''4.3.18. AT+QCFG="urc/cache"URC Cache Function - page 55'''] | |
| − | + | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=57 '''4.3.19. AT+QCFG="tone/incoming"Ring tone Function - page 56'''] | |
| − | + | ||
| − | + | [https://wiki.teltonika-networks.com/wikibase/images/2/2e/Quectel_EC25EC21_AT_Commands_Manual_V1.2.pdf#page=58 '''4.4. AT+QINDCFG URC Indication Configuration - page 57'''] | |
| − | + | ||
The command is used to control URC indication. | The command is used to control URC indication. | ||
| − | [[Category: | + | [[Category:TRM250 AT Commands]] |
Revision as of 11:15, 3 December 2019
TRM240 AT Commands > TRM240 AT Commands > TRM240 AT Commands > TRM240 AT Commands > TRM240 AT Commands > TRM240 AT Commands > TRM240 AT Commands > TRM240 AT Commands > TRM240 AT Commands > TRM240 AT Commands > Status Control CommandsStatus Control Commands
4.1. AT+CPAS Mobile Equipment Activity Status - page 37
TheExecutionCommand queries the module‟s activity status.
4.2. AT+CEER Extended Error Report - page 38
The commandis used to query an extended error and report the cause of the last failed operation, such as:
- the failure to release a call;
- the failure to set up a call (both mobile originated or terminated);
- the failure to modify a call by using supplementary services;
- the failure to activate, register, query, deactivate or deregister a supplementary service;
- the failureto attach GPRS or the failureto activatea PDP context;
- the failureto detach GPRS or the failureto deactivate a PDP context.
The release cause <text> is a text to describe the cause information given by the network.
4.3. AT+QCFG Extended Configuration Settings - page 39
The command is used to query and configure various settings of UE.
4.3.1. AT+QCFG="gprsattach" GPRS Attach Mode Configuration - page 40
The command specifies the mode to attach GPRS when UE is powered on. This configuration is valid only after the module is restarted.
4.3.2. AT+QCFG="nwscanmode" Network Search Mode Configuration - page 41
The commands pecifies the network mode to be serached. If <effect>is omitted, the configuration will take effect immediately.
4.3.3. AT+QCFG="nwscanseq" Network Searching Sequence Configuration - page 42
The command specifies the sequence of searching network. This configuration is valid only after the module is restarted.
4.3.4. AT+QCFG="roamservice" Roam Service Configuration - page 43
The command is used to enable or disable the roam service. If <effect>is omitted, the configuration will take effect immediately.
4.3.5. AT+QCFG="servicedomain" Service Domain Configuration - page 43
The command specifies the registered service domain. If <effect>is omitted, the configuration will take effect immediately.
4.3.6. AT+QCFG="band" Band Configuration - page 44
The command specifies the preferred frequency bands to be searched of UE. If <effect>is omitted, the configuration will take effect immediately.
4.3.7. AT+QCFG="hsdpacat" HSDPA Category Configuration - page 46
The command specifies the HSDPA category. This configuration is valid only after the module is restarted.
4.3.8. AT+QCFG="hsupacat" HSUPA Category Configuration - page 46
The command specifies the HSUPA category. This configuration is valid only after the module is restarted.
4.3.9. AT+QCFG="rrc" RRC Release Version Configuration - page 47
The command specifies the RRC release version. This configuration is valid only after the module is restarted.
4.3.10. AT+QCFG="sgsn" UE SGSN Release Version Configuration - page 48
The command specifies the UE SGSN release version. This configuration is valid only after the module is restarted.
4.3.11. AT+QCFG="msc" UE MSC Release Version Configuration - page 48
The commandspecifies the UE MSCrelease version. This configuration is valid only after the module is restarted.
4.3.12. AT+QCFG="PDP/duplicatechk"Establish Multi PDNs with the Same APN - page 49
The command allows/refuses establishing multi PDNs with the same APN profile. The configuration will take effect immediately.
4.3.13. AT+QCFG="urc/ri/ring" RI Behavior When RING URC is Presented - page 50
AT+QCFG="urc/ri/ring", AT+QCFG="urc/ri/smsincoming" and AT+QCFG="urc/ri/other"control the RI (ring indicator) behavior when a URC is reported. These configurations will be stored into NV automatically. The ring indicator is active low. AT+QCFG="urc/ri/ring" specifies the RI behavior when URC RING is presented to indicate an incoming call.
4.3.14. AT+QCFG="urc/ri/smsincoming" RIBehavior WhenIncoming SMSURCs are Presented - page 52
The command specifies the RI (ring indicator) behavior when related incoming message URCs are presented. Related incoming message URCs list: +CMTI,+CMT,+CDSand+CBM.
4.3.15. AT+QCFG="urc/ri/other" RI Behavior When Other URCsare Presented - page 53
The command specifies the RI (ring indicator)behavior when other URCs are presented.
4.3.16. AT+QCFG="risignaltype" RISignal Output Carrier - page 53
The command specifies the RI (ring indicator) signal output carrier.
4.3.17. AT+QCFG="urc/delay"Delay URC Indication - page 54
The commandcan delay the output ofURC indication until ring indicatorpulse ends.
4.3.18. AT+QCFG="urc/cache"URC Cache Function - page 55
4.3.19. AT+QCFG="tone/incoming"Ring tone Function - page 56
4.4. AT+QINDCFG URC Indication Configuration - page 57
The command is used to control URC indication.
