|
|
(46 intermediate revisions by 3 users not shown) |
Line 1: |
Line 1: |
| This wiki page contains information about {{{name}}} {{#switch: {{{series}}} | | This wiki page contains information about {{{name}}} {{#switch: {{{series}}} |
− | | TRB14x|TRB2xx|TRB5 = gateway | + | | TRB14x = gateway |
| + | | TRB2xx = gateway |
| | TRM2xx = modem | | | TRM2xx = modem |
− | | TSW1xx|TSW2xx|TSW3|TSW0 = switch | + | | TSW1xx = switch |
− | | router}} <b>LEDs</b> and their actions. | + | | router |
− | | |
− | __TOC__
| |
− | | |
− | ==Power LED==
| |
− | | |
− | The <b>power LED</b> is located on the bottom left corner of the front panel, near the power connector:
| |
− | | |
− | [[File:{{{file_power_led}}}|{{{size_power_led}}}px]]
| |
− | | |
− | It can perform two different actions:
| |
− | | |
− | <table class="nd-othertables_2">
| |
− | <tr>
| |
− | <th style="width: 550px>Action</th>
| |
− | <th style="width: 550px>Description</th>
| |
− | </tr>
| |
− | <tr>
| |
− | <td>LED turned ON</td>
| |
− | <td>{{#switch: {{{series}}}
| |
− | | TRB14x|TRB2xx|TRB5 = Gateway
| |
− | | TRM2xx = Modem
| |
− | | TSW1xx|TSW2xx|TSW3|TSW0 = Switch
| |
− | | Router}} is powered up</td>
| |
− | </tr>
| |
− | <tr>
| |
− | <td>LED turned OFF</td>
| |
− | <td>{{#switch: {{{series}}}
| |
− | | TRB14x|TRB2xx|TRB5 = Gateway
| |
− | | TRM2xx = Modem
| |
− | | TSW1xx|TSW2xx|TSW3|TSW0 = Switch
| |
− | | Router}} is not power up</td>
| |
− | </tr>
| |
− | </table>
| |
− | | |
− | <!-- Use if device has eth port -->
| |
− | {{#ifeq: {{{eth_leds}}} | 1
| |
− | |{{#ifeq: {{{name}}} | TRB140
| |
− | |{{Template: Networking_{{lc:{{{name}}}}}_manual_ethernet_port_leds
| |
− | | file_eth_led = {{{file_eth_led}}}
| |
− | | size_eth = {{{size_eth}}}
| |
− | }}
| |
− | |{{Template: Networking_{{lc:{{{series}}}}}_manual_ethernet_port_leds
| |
− | | file_eth_led = {{{file_eth_led}}}
| |
− | | size_eth = {{{size_eth}}}
| |
− | | name = {{{name}}}
| |
− | }}|
| |
− | }}
| |
| }} | | }} |
− |
| |
− | <!-- Use if device has SFP port -->
| |
− | {{#ifeq: {{{sfp_leds}}} | 1
| |
− | | {{Template: Networking_{{lc:{{{series}}}}}_manual_sfp_port_leds
| |
− | | file_sfp_led = {{{file_sfp_led}}}
| |
− | | size_sfp = {{{size_sfp}}}
| |
− | | name = {{{name}}}
| |
− | }}
| |
− | |
| |
− | }}
| |
− |
| |
− | <!-- Use if device has mobile module -->
| |
− | {{#ifeq: {{{con}}} | 1
| |
− | | {{Template: Networking_{{lc:{{{name}}}}}_manual_connection_status_leds
| |
− | | file_con_led = {{{file_con_led}}}
| |
− | | size_con = {{{size_con}}}
| |
− | }}
| |
− | |
| |
− | }}
| |
− |
| |
− | {{#ifeq: {{{sig}}} | 1
| |
− | | {{Template: Networking_{{lc:{{{series}}}}}_manual_signal_strength_leds
| |
− | | file_sig_led = {{{file_sig_led}}}
| |
− | | size_sig = {{{size_sig}}}
| |
− | }}
| |
− |
| |
− |
| |
− | The signal strength LEDs can also be used as a <b>time indicator for holding the reset button</b>. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a <b>User's default configuration reset</b> and 12 seconds (by default) to initiate a <b>Factory reset</b>. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a <b>Factory reset</b>. If the button was held down longer than 20 seconds (by default) no action will be taken.
| |
− |
| |
− | While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with <b>{{{name}}}</b>, when all {{{sig_led_num}}} signal strength LEDs are lit up, they represent that {{#expr: {{{sig_led_num}}} * 2}} (LED number multiplied by 2) seconds have passed since you pressed down on the reset button.
| |
− |
| |
− | After releasing the button at one of the reset periods, all {{{sig_led_num}}} LEDs will start blinking every 1 second. This signifies that the router <b>has begun the reset</b>.
| |
− | |
| |
− | }}
| |
− |
| |
− | [[Category:{{{name}}} Manual]]
| |