Difference between revisions of "Template:Networking device leds"
From Teltonika Networks Wiki
(Added information on Signal Strength LEDs and reset button when no User's defaults are configured.) |
|||
(35 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
This wiki page contains information about {{{name}}} {{#switch: {{{series}}} | This wiki page contains information about {{{name}}} {{#switch: {{{series}}} | ||
− | | TRB14x|TRB2xx | + | | TRB14x = gateway |
+ | | TRB2xx = gateway | ||
| TRM2xx = modem | | TRM2xx = modem | ||
− | | TSW1xx | + | | TSW1xx = switch |
− | | router}} <b>LEDs</b> and their actions. | + | | router |
+ | }} <b>LEDs</b> and their actions. | ||
__TOC__ | __TOC__ | ||
==Power LED== | ==Power LED== | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
<!-- Use if device has eth port --> | <!-- Use if device has eth port --> | ||
− | {{# | + | {{#if: {{{eth_leds|}}} |
− | | | + | | <br>{{Template: Networking_{{lc:{{{series}}}}}_manual_ethernet_port_leds |
− | + | | eth_led = {{{eth_led}}} | |
− | + | | size_eth = {{{size_eth}}} | |
− | + | }} | |
− | + | | {{#ifeq: {{{name}}} | TRB140 | |
− | + | | <br>{{Template: Networking_{{lc:{{{name}}}}}_manual_ethernet_port_leds | |
− | + | | eth_led = {{{eth_led}}} | |
− | + | | size_eth = {{{size_eth}}} | |
− | + | }} | |
− | + | }} | |
− | |||
− | |||
− | |||
− | |||
− | {{#ifeq: {{{ | ||
− | |||
− | |||
− | |||
− | |||
− | |||
| | | | ||
}} | }} | ||
<!-- Use if device has mobile module --> | <!-- Use if device has mobile module --> | ||
− | {{# | + | {{#if: {{{con|}}} |
− | | {{Template: Networking_{{lc:{{{name}}}}}_manual_connection_status_leds | + | | <br>{{Template: Networking_{{lc:{{{name}}}}}_manual_connection_status_leds |
− | | | + | | con_led = {{{con_led}}} |
| size_con = {{{size_con}}} | | size_con = {{{size_con}}} | ||
}} | }} | ||
Line 72: | Line 35: | ||
}} | }} | ||
− | {{# | + | {{#if: {{{sig|}}} |
− | | {{Template: Networking_{{lc:{{{series}}}}}_manual_signal_strength_leds | + | | <br>{{Template: Networking_{{lc:{{{series}}}}}_manual_signal_strength_leds |
− | | | + | | sig_led = {{{con_led}}} |
− | | size_sig = {{{ | + | | size_sig = {{{size_con}}} |
}} | }} | ||
+ | | | ||
+ | }} | ||
+ | {{#if: {{{sig|}}} | ||
+ | | The signal strength LEDs can also be used as a time indicator for holding the reset button. When you press and hold the reset button, you have to hold it pressed for 5 seconds (by default) to initiate a factory reset. Each second, a new signal strength LED lights up. When all {{{sig_led_num}}} LEDs are lit up, it represents that 5 seconds have passed since you pressed down on the reset button and that you can release it. | ||
− | + | After releasing the button, all {{{sig_led_num}}} LEDs will start blinking every 1 second. This signifies that the router has begun the factory reset. | |
− | |||
− | |||
− | |||
− | After releasing the button | ||
| | | | ||
}} | }} | ||
− | [[Category:{{{name}}} | + | [[Category:{{{name}}}]] |
Revision as of 09:11, 1 April 2020
This wiki page contains information about {{{name}}} router LEDs and their actions.
Power LED
[[Category:{{{name}}}]]