Line 26: |
Line 26: |
| After login in to your router, you need to set up your <b>WAN</b>. To find <b>WAN</b> configuration, you need to navigate to “Network→WAN”. You should see a web page like in the picture below. | | After login in to your router, you need to set up your <b>WAN</b>. To find <b>WAN</b> configuration, you need to navigate to “Network→WAN”. You should see a web page like in the picture below. |
| | | |
− | [[File:rutx_wan_settings_page_v1.jpg|border|class=tlt-border]] | + | [[File:{{{wan_settings_page}}}|border|class=tlt-border]] |
| | | |
| How to set up your <b>WAN</b> configuration can be found [[RUTX10_WAN|here]]. | | How to set up your <b>WAN</b> configuration can be found [[RUTX10_WAN|here]]. |
Line 34: |
Line 34: |
| When <b>WAN</b> configuration is done, it’s time to configure VLAN’s. VLAN configuration can be found by navigating to “Network→VLAN”. You should see a page like in the picture below. | | When <b>WAN</b> configuration is done, it’s time to configure VLAN’s. VLAN configuration can be found by navigating to “Network→VLAN”. You should see a page like in the picture below. |
| | | |
− | [[File:rutx_vlan_settings_page_v1.jpg|border|class=tlt-border]] | + | [[File:{{{vlan_settings_page}}}|border|class=tlt-border]] |
| | | |
| ---- | | ---- |
| Now press the “ADD” button, which is located in the “VLANS ON SWITCH0” section. | | Now press the “ADD” button, which is located in the “VLANS ON SWITCH0” section. |
| | | |
− | [[File:rutx_add_vlan_section_v1.png|border|class=tlt-border]] | + | [[File:{{{vlan_section_add}}}|border|class=tlt-border]] |
| | | |
| A new row should appear in the “VLANS ON SWITCH0” section. | | A new row should appear in the “VLANS ON SWITCH0” section. |
| | | |
− | [[File:Rutx_vlan_switch_section_before_v1.jpg|border|class=tlt-border]] | + | [[File:{{{vlan_section_configuration}}}|border|class=tlt-border]] |
| | | |
| ---- | | ---- |
Line 51: |
Line 51: |
| <li>Change your desired LAN port to "untagged"</li> | | <li>Change your desired LAN port to "untagged"</li> |
| <li>Change WAN port to "tagged"</li> | | <li>Change WAN port to "tagged"</li> |
− | </ol>[[File:rutx_vlan_switch_section_after_v1.jpg|border|class=tlt-border]] | + | </ol>[[File:{{{vlan_section_configurated}}}|border|class=tlt-border]] |
| </li> | | </li> |
| | | |
Line 66: |
Line 66: |
| After configuring VLAN, the desired port does not have an IP address because now that port is using a new interface which has no configuration yet. You can configure the interface through LAN configuration page. The <b>LAN</b> configuration page can be found by navigating to “Network→LAN”. | | After configuring VLAN, the desired port does not have an IP address because now that port is using a new interface which has no configuration yet. You can configure the interface through LAN configuration page. The <b>LAN</b> configuration page can be found by navigating to “Network→LAN”. |
| | | |
− | [[File:rutx_lan_settings_page_before_v1.jpg|border|class=tlt-border]] | + | [[File:{{{lan_settings_page}}}|border|class=tlt-border]] |
| ---- | | ---- |
| <li>Now lets add an interface for the new added VLAN: | | <li>Now lets add an interface for the new added VLAN: |
Line 73: |
Line 73: |
| <li>Select the new created interface from the interface list. It should be named like this '''eth0.<VLAN_ID>'''</li> | | <li>Select the new created interface from the interface list. It should be named like this '''eth0.<VLAN_ID>'''</li> |
| <li>Click the "<b>ADD</b>" button</li> | | <li>Click the "<b>ADD</b>" button</li> |
− | </ol>[[File:rutx_add_lan_interface_v1.jpg|border|class=tlt-border]] | + | </ol>[[File:{{{lan_add_interface}}}|border|class=tlt-border]] |
| </li> | | </li> |
| ---- | | ---- |
Line 79: |
Line 79: |
| <ol> | | <ol> |
| <li>Click the "<b>SWITCH PROTOCOL</b>" button</li> | | <li>Click the "<b>SWITCH PROTOCOL</b>" button</li> |
− | </ol>[[File:rutx_switch_lan_protocol_v1.jpg|border|class=tlt-border]] | + | </ol>[[File:{{{lan_switch_protocol}}}|border|class=tlt-border]] |
| </li> | | </li> |
| ---- | | ---- |
Line 87: |
Line 87: |
| <li>Select the necessary netmask for your subnet</li> | | <li>Select the necessary netmask for your subnet</li> |
| <li>Enable DHCP server</li> | | <li>Enable DHCP server</li> |
− | </ol>[[File:rutx_configure_lan_interface_v1.jpg|border|class=tlt-border]] | + | </ol>[[File:{{{lan_interface_configuration}}}|border|class=tlt-border]] |
| </li> | | </li> |
| After changing the values press the "'''SAVE & APPLY'''" button for our configuration to take effect. | | After changing the values press the "'''SAVE & APPLY'''" button for our configuration to take effect. |
Line 93: |
Line 93: |
| After saving the configuration, you should be redirected to main <b>LAN</b> page. | | After saving the configuration, you should be redirected to main <b>LAN</b> page. |
| | | |
− | [[File:rutx_lan_settings_after_v1.jpg|border|class=tlt-border]] | + | [[File:{{{lan_interface_configurated}}}|border|class=tlt-border]] |
| | | |
| If you need a more detailed explanation about LANs, you can find it [[RUTX10_LAN|here]]. | | If you need a more detailed explanation about LANs, you can find it [[RUTX10_LAN|here]]. |