Line 1: |
Line 1: |
| + | {{Template: Networking_rutxxx_manual_fw_disclosure |
| + | | fw_version = {{{fw_version}}} |
| + | }} |
| ==Summary== | | ==Summary== |
| | | |
| This chapter is an overview of the Routing section in RUT devices. | | This chapter is an overview of the Routing section in RUT devices. |
− |
| |
− | {{Template: Networking_rutxxx_manual_fw_disclosure
| |
− | | fw_version = RUT2XX_R_00.01.11.3
| |
− | }}
| |
| | | |
| ==Static Routes== | | ==Static Routes== |
Line 15: |
Line 14: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Routing table</td> | | <td>Routing table</td> |
− | <td>Main | WAN | WAN2 | WAN3; Default: '''WAN'''</td> | + | <td>Main | WAN | WAN2 | WAN3; default: '''WAN'''</td> |
| <td>Defines which table will be used for the route in question</td> | | <td>Defines which table will be used for the route in question</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Interface</td> | | <td>Interface</td> |
− | <td>LAN | WAN(Wired) | WAN2(Mobile) | WAN3(WiFi) | VPN instances; Default: '''WAN(Wired)'''</td> | + | <td>LAN | WAN(Wired) | WAN2(Mobile) | WAN3(WiFi) | VPN instances; default: '''WAN(Wired)'''</td> |
| <td>The zone where the target network resides</td> | | <td>The zone where the target network resides</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Destination address'''*'''</td> | | <td>Destination address'''*'''</td> |
− | <td>ip; Default: '''0.0.0.0'''</td> | + | <td>ip; default: '''0.0.0.0'''</td> |
| <td>The address of the destination network</td> | | <td>The address of the destination network</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Netmask'''*'''</td> | | <td>Netmask'''*'''</td> |
− | <td>ip; Default: '''0.0.0.0'''</td> | + | <td>ip; default: '''0.0.0.0'''</td> |
| <td>A Mask that is applied to the Target to determine to what actual IP addresses the routing rule applies</td> | | <td>A Mask that is applied to the Target to determine to what actual IP addresses the routing rule applies</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Gateway</td> | | <td>Gateway</td> |
− | <td>ip; Default: " "</td> | + | <td>ip; default: <b>none</b></td> |
| <td>Defines where the router should send all the traffic that applies to the rule</td> | | <td>Defines where the router should send all the traffic that applies to the rule</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Metric</td> | | <td>Metric</td> |
− | <td>integer; Default: '''0'''</td> | + | <td>integer; default: '''0'''</td> |
− | <td>The '''Metric''' value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the higher metric is applied</td> | + | <td>The '''Metric''' Value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the higher metric is applied</td> |
| </tr> | | </tr> |
| </table> | | </table> |
Line 56: |
Line 55: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
Line 94: |
Line 93: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Interface</td> | | <td>Interface</td> |
− | <td>Wired WAN IPv6 <nowiki>|</nowiki> Mobile WAN IPv6 <nowiki>|</nowiki> Wi-Fi IPv6; Default: '''Wired WAN IPv6'''</td> | + | <td>Wired WAN IPv6 <nowiki>|</nowiki> Mobile WAN IPv6 <nowiki>|</nowiki> Wi-Fi IPv6; default: '''Wired WAN IPv6'''</td> |
| <td>Defines which interface will be used</td> | | <td>Defines which interface will be used</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Target</td> | | <td>Target</td> |
− | <td>Default: " "</td> | + | <td>default: <b>none</b></td> |
| <td>The address of the destination network</td> | | <td>The address of the destination network</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>IPv6-Gateway</td> | | <td>IPv6-Gateway</td> |
− | <td>ipv6; Default: " "</td> | + | <td>ipv6; default: <b>none</b></td> |
| <td>Defines where the router should send all the traffic that applies to the rule</td> | | <td>Defines where the router should send all the traffic that applies to the rule</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Metric</td> | | <td>Metric</td> |
− | <td>integer; Default: '''0'''</td> | + | <td>integer; default: '''0'''</td> |
− | <td>The '''Metric''' value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the higher metric is applied</td> | + | <td>The '''Metric''' Value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the higher metric is applied</td> |
| </tr> | | </tr> |
| </table> | | </table> |
Line 140: |
Line 139: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles the BGP protocol ON or OFF</td> | | <td>Toggles the BGP protocol ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable vty</td> | | <td>Enable vty</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles vty access from LAN ON or OFF</td> | | <td>Toggles vty access from LAN ON or OFF</td> |
| </tr> | | </tr> |
Line 168: |
Line 167: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles the BGP instance ON or OFF</td> | | <td>Toggles the BGP instance ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Use IPv6</td> | | <td>Use IPv6</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Use IPv6 address family in the configuration</td> | | <td>Use IPv6 address family in the configuration</td> |
| </tr> | | </tr> |
Line 189: |
Line 188: |
| <tr> | | <tr> |
| <td>BGP router ID</td> | | <td>BGP router ID</td> |
− | <td>string; Default: " "</td> | + | <td>string; default: <b>none</b></td> |
− | <td>The router id is used by BGP to identify the routing device from which a packet originated. Default router ID value is selected as the largest IP Address of the interface.</td> | + | <td>The router id is used by BGP to identify the routing device from which a packet originated. Default router ID Value is selected as the largest IP Address of the interface.</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Network</td> | | <td>Network</td> |
− | <td>string; Default: " "</td> | + | <td>string; default: <b>none</b></td> |
| <td>Add an announcement network(s)</td> | | <td>Add an announcement network(s)</td> |
| </tr> | | </tr> |
Line 206: |
Line 205: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles the BGP peer ON or OFF</td> | | <td>Toggles the BGP peer ON or OFF</td> |
| </tr> | | </tr> |
Line 222: |
Line 221: |
| <tr> | | <tr> |
| <td>Remote address</td> | | <td>Remote address</td> |
− | <td>ip; Default: " "</td> | + | <td>ip; default: <b>none</b></td> |
| <td>Neighbour's remote IPv4 address</td> | | <td>Neighbour's remote IPv4 address</td> |
| </tr> | | </tr> |
Line 234: |
Line 233: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles the Access filter ON or OFF</td> | | <td>Toggles the Access filter ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Peer</td> | | <td>Peer</td> |
− | <td>bgp peer; Default: '''first peer on list'''</td> | + | <td>bgp peer; default: '''first peer on list'''</td> |
| <td>Applies the rule for the specified peer</td> | | <td>Applies the rule for the specified peer</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Action</td> | | <td>Action</td> |
− | <td>Permit | Deny; Default: '''Permit'''</td> | + | <td>Permit | Deny; default: '''Permit'''</td> |
| <td>Denies or permits matched entry</td> | | <td>Denies or permits matched entry</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Network</td> | | <td>Network</td> |
− | <td>Any | ip; Default: '''Any'''</td> | + | <td>Any | ip; default: '''Any'''</td> |
| <td>Applies filter rule for this source network</td> | | <td>Applies filter rule for this source network</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Direction</td> | | <td>Direction</td> |
− | <td>Inbound | Outbound; Default: '''Inbound'''</td> | + | <td>Inbound | Outbound; default: '''Inbound'''</td> |
| <td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td> | | <td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td> |
| </tr> | | </tr> |
Line 276: |
Line 275: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles RIP Protocol ON or OFF</td> | | <td>Toggles RIP Protocol ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable vty</td> | | <td>Enable vty</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles vty access from LAN ON or OFF</td> | | <td>Toggles vty access from LAN ON or OFF</td> |
| </tr> | | </tr> |
Line 297: |
Line 296: |
| <tr> | | <tr> |
| <td>Version</td> | | <td>Version</td> |
− | <td>2 | 1; Default: '''2'''</td> | + | <td>2 | 1; default: '''2'''</td> |
| <td>Specifies the version of RIP</td> | | <td>Specifies the version of RIP</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Neighbor</td> | | <td>Neighbor</td> |
− | <td>ip; Default: " "</td> | + | <td>ip; default: <b>none</b></td> |
| <td>Neighbour IP addres</td> | | <td>Neighbour IP addres</td> |
| </tr> | | </tr> |
Line 314: |
Line 313: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles RIP Interface ON or OFF</td> | | <td>Toggles RIP Interface ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Interface</td> | | <td>Interface</td> |
− | <td>network interface; Default: '''no'''</td> | + | <td>network interface; default: '''no'''</td> |
| <td>Network interface to be used with the RIP interface</td> | | <td>Network interface to be used with the RIP interface</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Passive interface</td> | | <td>Passive interface</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Sets the specified interface to passive mode. On passive mode interface, all receiving packets are processed as normal and ripd does not send either multicast or unicast RIP packets</td> | | <td>Sets the specified interface to passive mode. On passive mode interface, all receiving packets are processed as normal and ripd does not send either multicast or unicast RIP packets</td> |
| </tr> | | </tr> |
Line 342: |
Line 341: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles the Access filter ON or OFF</td> | | <td>Toggles the Access filter ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Peer</td> | | <td>Peer</td> |
− | <td>bgp peer; Default: '''first peer on list'''</td> | + | <td>bgp peer; default: '''first peer on list'''</td> |
| <td>Applies the rule for the specified peer</td> | | <td>Applies the rule for the specified peer</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Action</td> | | <td>Action</td> |
− | <td>Permit | Deny; Default: '''Permit'''</td> | + | <td>Permit | Deny; default: '''Permit'''</td> |
| <td>Denies or permits matched entry</td> | | <td>Denies or permits matched entry</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Network</td> | | <td>Network</td> |
− | <td>Any | ip; Default: '''Any'''</td> | + | <td>Any | ip; default: '''Any'''</td> |
| <td>Applies filter rule for this source network</td> | | <td>Applies filter rule for this source network</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Direction</td> | | <td>Direction</td> |
− | <td>Inbound | Outbound; Default: '''Inbound'''</td> | + | <td>Inbound | Outbound; default: '''Inbound'''</td> |
| <td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td> | | <td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td> |
| </tr> | | </tr> |
Line 383: |
Line 382: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles OSPF Protocol ON or OFF</td> | | <td>Toggles OSPF Protocol ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable vty</td> | | <td>Enable vty</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles vty access from LAN ON or OFF</td> | | <td>Toggles vty access from LAN ON or OFF</td> |
| </tr> | | </tr> |
Line 404: |
Line 403: |
| <tr> | | <tr> |
| <td>Router ID</td> | | <td>Router ID</td> |
− | <td>ip; Default: " "</td> | + | <td>ip; default: <b>none</b></td> |
| <td>Sets the router-ID of the OSPF process. The router-ID may be an IP address of the router, but need not be - it can be any arbitrary 32bit number</td> | | <td>Sets the router-ID of the OSPF process. The router-ID may be an IP address of the router, but need not be - it can be any arbitrary 32bit number</td> |
| </tr> | | </tr> |
Line 415: |
Line 414: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles OSPF interface ON or OFF</td> | | <td>Toggles OSPF interface ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Cost</td> | | <td>Cost</td> |
− | <td>integer [1..65535]; Default: '''10'''</td> | + | <td>integer [1..65535]; default: '''10'''</td> |
− | <td>The cost value is set to router-LSA’s metric field and used for SPF calculation</td> | + | <td>The cost Value is set to router-LSA’s metric field and used for SPF calculation</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Hello interval</td> | | <td>Hello interval</td> |
− | <td>integer [1..65535]; Default: '''10'''</td> | + | <td>integer [1..65535]; default: '''10'''</td> |
| <td>Hello packets will be sent at the frequency specified in this field (in seconds)</td> | | <td>Hello packets will be sent at the frequency specified in this field (in seconds)</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Router dead interval</td> | | <td>Router dead interval</td> |
− | <td>integer [1..65535]; Default: '''40'''</td> | + | <td>integer [1..65535]; default: '''40'''</td> |
− | <td>This value must be the same for all routers attached to a common network</td> | + | <td>This Value must be the same for all routers attached to a common network</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Retransmit</td> | | <td>Retransmit</td> |
− | <td>integer [1..65535]; Default: '''5'''</td> | + | <td>integer [1..65535]; default: '''5'''</td> |
− | <td>This value is used when re-transmitting Database Description and Link State Request packets</td> | + | <td>This Value is used when re-transmitting Database Description and Link State Request packets</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Priority</td> | | <td>Priority</td> |
− | <td>integer [0..255]; Default: '''1'''</td> | + | <td>integer [0..255]; default: '''1'''</td> |
− | <td>The router with the highest priority will be more eligible to become the Designated Router. Setting the value to 0, makes the router ineligible to become the Designated Router</td> | + | <td>The router with the highest priority will be more eligible to become the Designated Router. Setting the Value to 0, makes the router ineligible to become the Designated Router</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Type</td> | | <td>Type</td> |
− | <td>Broadcast | Nonbroadcast | Point-to-point | Point-to-multipoint; Default: " "</td> | + | <td>Broadcast | Nonbroadcast | Point-to-point | Point-to-multipoint; default: <b>none</b></td> |
| <td>Set explicit network type for the specified interface</td> | | <td>Set explicit network type for the specified interface</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Authentication</td> | | <td>Authentication</td> |
− | <td>None | Password | MD5 HMAC; Default: " "</td> | + | <td>None | Password | MD5 HMAC; default: <b>none</b></td> |
| <td>Specifies the authentication mode that should be used for the interface</td> | | <td>Specifies the authentication mode that should be used for the interface</td> |
| </tr> | | </tr> |
Line 468: |
Line 467: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>yes | no; Default: '''no'''</td> | + | <td>yes | no; default: '''no'''</td> |
| <td>Toggles OSPF network ON or OFF</td> | | <td>Toggles OSPF network ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Network</td> | | <td>Network</td> |
− | <td>[a.b.c.d/m]; Default: " "</td> | + | <td>[a.b.c.d/m]; default: <b>none</b></td> |
| <td>This command specifies the OSPF enabled interface. If the interface has an address from the range '''a.b.c.d/m''' then enables OSPF on this interface so the router can provide network information to the other OSPF routers via this interface</td> | | <td>This command specifies the OSPF enabled interface. If the interface has an address from the range '''a.b.c.d/m''' then enables OSPF on this interface so the router can provide network information to the other OSPF routers via this interface</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Area</td> | | <td>Area</td> |
− | <td>ospf area; Default: " "</td> | + | <td>ospf area; default: <b>none</b></td> |
| <td>Specifies OSPF area</td> | | <td>Specifies OSPF area</td> |
| </tr> | | </tr> |
Line 503: |
Line 502: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable service</td> | | <td>Enable service</td> |
− | <td>off <nowiki>|</nowiki> on; Default: '''off'''</td> | + | <td>off <nowiki>|</nowiki> on; default: '''off'''</td> |
| <td>Toggles NHRP between ON or OFF</td> | | <td>Toggles NHRP between ON or OFF</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable logging</td> | | <td>Enable logging</td> |
− | <td>off <nowiki>|</nowiki> on; Default: '''off'''</td> | + | <td>off <nowiki>|</nowiki> on; default: '''off'''</td> |
| <td>Toggles NHRP logging between ON or OFF</td> | | <td>Toggles NHRP logging between ON or OFF</td> |
| </tr></table> | | </tr></table> |
Line 527: |
Line 526: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>off <nowiki>|</nowiki> on; Default: '''off'''</td> | + | <td>off <nowiki>|</nowiki> on; default: '''off'''</td> |
| <td>Toggles interface ON or OFF</td> | | <td>Toggles interface ON or OFF</td> |
| </tr></table> | | </tr></table> |
Line 546: |
Line 545: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Enable</td> | | <td>Enable</td> |
− | <td>off <nowiki>|</nowiki> on; Default: '''off'''</td> | + | <td>off <nowiki>|</nowiki> on; default: '''off'''</td> |
| <td>Enables DMVPN client</td> | | <td>Enables DMVPN client</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Interface</td> | | <td>Interface</td> |
− | <td>interfaces; Default: '''br-lan''' | + | <td>interfaces; default: '''br-lan''' |
| </td> | | </td> |
| <td>Interface which will be using NHRP</td> | | <td>Interface which will be using NHRP</td> |
Line 563: |
Line 562: |
| <tr> | | <tr> |
| <td>Network ID</td> | | <td>Network ID</td> |
− | <td>number; Default: '''none''' | + | <td>number; default: '''none''' |
| </td> | | </td> |
| <td>Network ID of NHRP</td> | | <td>Network ID of NHRP</td> |
Line 569: |
Line 568: |
| <tr> | | <tr> |
| <td>NHS</td> | | <td>NHS</td> |
− | <td>None <nowiki>|</nowiki> Dynamic <nowiki>|</nowiki> Custom; Default: '''none''' | + | <td>None <nowiki>|</nowiki> Dynamic <nowiki>|</nowiki> Custom; default: '''none''' |
| </td> | | </td> |
| <td>IP address of Next-Hop Server. | | <td>IP address of Next-Hop Server. |
Line 576: |
Line 575: |
| <tr> | | <tr> |
| <td>NBMA</td> | | <td>NBMA</td> |
− | <td>ip; Default: '''none''' | + | <td>ip; default: '''none''' |
| </td> | | </td> |
| <td>Non-Broadcast Multi-Access(NBMA) network IP address</td> | | <td>Non-Broadcast Multi-Access(NBMA) network IP address</td> |
Line 582: |
Line 581: |
| <tr> | | <tr> |
| <td>Hold-time</td> | | <td>Hold-time</td> |
− | <td>number; Default: '''7200''' | + | <td>number; default: '''7200''' |
| </td> | | </td> |
| <td>Specifies the holding time for NHRP Registration Requests and Resolution Replies sent from this interface or shortcut-target. The holdtime is specified in seconds and defaults to two hours.</td> | | <td>Specifies the holding time for NHRP Registration Requests and Resolution Replies sent from this interface or shortcut-target. The holdtime is specified in seconds and defaults to two hours.</td> |
Line 588: |
Line 587: |
| <tr> | | <tr> |
| <td>IPsec support</td> | | <td>IPsec support</td> |
− | <td>off <nowiki>|</nowiki> on; Default: '''off''' | + | <td>off <nowiki>|</nowiki> on; default: '''off''' |
| </td> | | </td> |
| <td>Use NHRP over IPsec</td> | | <td>Use NHRP over IPsec</td> |
Line 601: |
Line 600: |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
| <tr> | | <tr> |
− | <th>field name</th> | + | <th>Field</th> |
− | <th>value</th> | + | <th>Value</th> |
− | <th>description</th> | + | <th>Description</th> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>IP address</td> | | <td>IP address</td> |
− | <td>ip; Default: '''none''' | + | <td>ip; default: '''none''' |
| </td> | | </td> |
| <td>Network ID of NHRP</td> | | <td>Network ID of NHRP</td> |
Line 613: |
Line 612: |
| <tr> | | <tr> |
| <td>NBMA</td> | | <td>NBMA</td> |
− | <td>ip; Default: '''none''' | + | <td>ip; default: '''none''' |
| </td> | | </td> |
| <td>IP address of Next-Hop Server</td> | | <td>IP address of Next-Hop Server</td> |