31,703
edits
Changes
Template:Networking rut230 manual modbus modbus tcp set parameters table (view source)
Revision as of 07:26, 15 October 2020
, 07:26, 15 October 2020Created page with "<table class="nd-othertables"> <tr> <th width="350">value to set</th> <th width="180">register address</th> <th width="150">register value</th>..."
<table class="nd-othertables">
<tr>
<th width="350">value to set</th>
<th width="180">register address</th>
<th width="150">register value</th>
<th width="466">description</th>
</tr>
<tr>
<td>Hostname</td>
<td>7</td>
<td>Hostname</td>
<td>Changes hostname</td>
</tr>
<tr>
<td>Device name</td>
<td>71</td>
<td>Device name</td>
<td>Changes device name</td>
</tr>
<tr>
<td>Switch WiFi (ON/OFF<span class="asterisk">*</span>)</td>
<td>203</td>
<td>1 | 0</td>
<td>Turns WiFi ON or OFF</td>
</tr>
<tr>
<td>Switch mobile data connection (ON/OFF<span class="asterisk">*</span>)</td>
<td>204</td>
<td>1 | 0</td>
<td>Turns mobile data connection ON or OFF</td>
</tr>
<tr>
<td>Reboot</td>
<td>206</td>
<td>1</td>
<td>Reboots the router</td>
</tr>
<tr>
<td>Change APN</td>
<td>207</td>
<td>APN code</td>
<td>Changes APN.<br>The number of input registers may vary depending on the length of the APN, but the very first byte of the set APN command has to be specified as <b>1</b></td>
</tr>
<tr>
<td>Switch PIN4 state (ON/OFF<span class="asterisk">*</span>)</td>
<td>325</td>
<td>1 | 0</td>
<td>Turns PIN4 state ON or OFF</td>
</tr>
</table>
<tr>
<th width="350">value to set</th>
<th width="180">register address</th>
<th width="150">register value</th>
<th width="466">description</th>
</tr>
<tr>
<td>Hostname</td>
<td>7</td>
<td>Hostname</td>
<td>Changes hostname</td>
</tr>
<tr>
<td>Device name</td>
<td>71</td>
<td>Device name</td>
<td>Changes device name</td>
</tr>
<tr>
<td>Switch WiFi (ON/OFF<span class="asterisk">*</span>)</td>
<td>203</td>
<td>1 | 0</td>
<td>Turns WiFi ON or OFF</td>
</tr>
<tr>
<td>Switch mobile data connection (ON/OFF<span class="asterisk">*</span>)</td>
<td>204</td>
<td>1 | 0</td>
<td>Turns mobile data connection ON or OFF</td>
</tr>
<tr>
<td>Reboot</td>
<td>206</td>
<td>1</td>
<td>Reboots the router</td>
</tr>
<tr>
<td>Change APN</td>
<td>207</td>
<td>APN code</td>
<td>Changes APN.<br>The number of input registers may vary depending on the length of the APN, but the very first byte of the set APN command has to be specified as <b>1</b></td>
</tr>
<tr>
<td>Switch PIN4 state (ON/OFF<span class="asterisk">*</span>)</td>
<td>325</td>
<td>1 | 0</td>
<td>Turns PIN4 state ON or OFF</td>
</tr>
</table>
