Difference between revisions of "TRB143 LEDs"
Gytispieze (talk | contribs) m (Gytispieze moved page Draft:TRB143 LEDs to TRB143 LEDs without leaving a redirect) |
Gytispieze (talk | contribs) (Created page with "{{Template: Networking_rutos_manual_leds <!------------------------DEVICE-----------------------> | name = TRB143 | series = TRB1 <!----------------------SEPARATOR...") |
(No difference)
|
Revision as of 17:10, 13 April 2022
Main Page > TRB Gateways > TRB143 > TRB143 Manual > TRB143 LEDsThis page contains information the different types of LEDs and their behaviour on a TRB143 device.
Power LED
The power LED is located on the bottom left corner of the front panel, just under the power connector.
It indicates whether the device is powered on or not.
State | Description |
---|---|
LED turned on | Device is powered on. |
LED turned off | Device is not powered on. |
Ethernet port LEDs
There are two LEDs located at the top of each Ethernet port.
They provide information on the current states of the Ethernet ports. Each port has two LEDs:
- Orange - 10/100 Mbps connection
- Green- 1000 Mbps connection
Below is an explanation on the behaviours of green and orange LEDs.
State | Description |
---|---|
LED on | A data connection on the port is operational (cable plugged in, end device visible, no data is being transferred). |
LED off | No data connection on the port is operational (no cable, bad cable or end device not visible for some other reason (such as damaged network card). |
LED blinking | Connection established and data is being transferred over this port. |
Mobile network type LEDs
The mobile network type LEDs are located near the SIM card slot.
They display which type of Internet connection is currently active.
Action | Description |
---|---|
2G LED turned on | Device is connected to a 2G network. |
3G LED turned on | Device is connected to a 3G network. |
4G LED turned on | Device is connected to a 4G network. |
2G blinking | Device is connected to a 2G network but hasn't received an IP address. |
3G blinking | Device is connected to a 3G network but hasn't received an IP address. |
4G blinking | Device is connected to a 4G network but hasn't received an IP address. |
All LEDs blinking at the same time every 500 ms | No SIM card or incorrect PIN. |
All LEDs turn on and off in a sequence one after the other | The device is attempting to connect to a mobile network operator. |
Mobile signal strength indication LEDs
The mobile signal strength indication LEDs are located near the SIM card slot.
The number of lit up LEDs represents a different mobile signal strength (RSSI) value in dBm.
No. of lit up LEDs | Signal strength value |
---|---|
0 | ≤ -111 dBm |
1 | -110 dBm to -82 dBm |
2 | -81 dBm to -52 dBm |
3 | ≥ -51 dBm |
The Mobile signal strength LEDs can also be used as a time indicator for holding the reset button. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a User's default configuration reset and 12 seconds (by default) to initiate a Factory reset. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a Factory reset. If the button was held down longer than 20 seconds (by default) no action will be taken.
While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with TRB143, when all 3 Mobile signal strength LEDs are lit up, they represent that 6 (LED number multiplied by 2) seconds have passed since you pressed down on the reset button.
After releasing the button at one of the reset periods, all 3 LEDs will start blinking every 1 second. This signifies that the router has begun the reset.