24
edits
Changes
OSPF via VPLS and ZerotierVPN (view source)
Revision as of 16:56, 17 October 2022
, 16:56, 17 October 2022no edit summary
*At least one end device (PC, Laptop, Tablet, Smartphone) to configure the routers
*At least one end device (PC, Laptop, Tablet, Smartphone) to configure the routers
*VPLS or any L2/L3 type of wired data channel.
*VPLS or any L2/L3 type of wired data channel.
*Sim card to reserve mobile channel.
*Wired or wireless internet connection.
==Summary==
==Summary==
*On newly created VLAN ID (3 in this example), from drop-down list, select <b>Untagged</b>, on same port.
*On newly created VLAN ID (3 in this example), from drop-down list, select <b>Untagged</b>, on same port.
*After performing these actions press <b>Save & Apply</b> in VLAN settings.
*After performing these actions press <b>Save & Apply</b> in VLAN settings.
[[File:OSPF via VPLS and ZerotierVPN VPN setting.png]]
==Add new VPLS interface (interface VLAN)==
==Add new VPLS interface (interface VLAN)==
[[File:OSPF via VPLS and ZerotierVPN Interface Vlan add.png]]
After doing that you will be redirected to new window to set up new interface, when there:
After doing that you will be redirected to new window to set up new interface, when there:
*Write IPv4 address to private address VPLS connections.
*Write IPv4 address to private address VPLS connections.
*Write IPv4 netmask to private address VPLS connections.
*Write IPv4 netmask to private address VPLS connections.
[[File:OSPF via VPLS and ZerotierVPN Interface Static setting.png]]
After switching protocol More setting options will appear:
After switching protocol More setting options will appear:
*Go to <b>Physical Settings.</b>
* Go to <b>Physical Settings.</b>
*From drop-down list choose previously created VLAN interface (in this example it is eth0.3)
* From drop-down list choose previously created VLAN interface (in this example it is eth0.3)
*Press <b>Apply & Save.</b>
*Press <b>Apply & Save.</b>
[[File:OSPF via VPLS and ZerotierVPN Interface setting.png]]
==Check new VPLS interface==
==Check new VPLS interface==
Insert VPLS cable in selected port, go to <b>Network > Interfaces</b> WebUI section and if you followed steps correctly yours newly created VPLS interface should be running and have an IP.
Insert VPLS cable in selected port, go to <b>Network > Interfaces</b> WebUI section and if you followed steps correctly yours newly created VPLS interface should be running and have an IP.
[[File:OSPF via VPLS and ZerotierVPN VPLS Interface.png]]
==ZeroTier One VPN configuration RutOS==
[[File:OSPF via VPLS and ZerotierVPN OSPF Zerotier.png]]
Wiki docks to
Wiki docks to [[ZeroTier One VPN configuration|ZeroTier VPN configuration]]
[[ZeroTier One VPN configuration|ZeroTier VPN configuration]]
[[File:OSPF via VPLS and ZerotierVPN OSPF Zerotier CLI.png]]
==Configure General settings OSPF Protocol==
==Configure General settings OSPF Protocol==
Go to <b>Network > Routing > Dynamik Routes > OSPF</b> WebUI section.
Go to <b>Network > Routing > Dynamik Routes > OSPF</b> WebUI section.
[[File:OSPF via VPLS and ZerotierVPN OSPF General.png]]
*Enable OSPF instance on check bar.
* Enable OSPF instance on check bar.
*Enable VTY access from LAN ON.
* Enable VTY access from LAN ON.
*Generate a default external route from drop-down list, select <b>Default</b>, Default - Advertises the default route if the route is in the route table.
*Generate a default external route from drop-down list, select <b>Default</b>, Default - Advertises the default route if the route is in the route table.
*Redistribution options, from drop-down list, select <b>Connected</b>. It redistribute connected network to another routers on same network.
*Redistribution options, from drop-down list, select <b>Connected</b>. It redistribute connected network to another routers on same network.
==Configure OSPF Interface==
==Configure OSPF Interface==
In this concept we need make priority on VPLS data channel, to minimize delay.
In this concept we need make priority on VPLS data channel, to minimize delay.
[[File:OSPF via VPLS and ZerotierVPN OSPF Interface Temp.png]
*Add new OSPF interface.
*Add new OSPF interface.
*Change Name Interface from drop-down list, select <b>VPLS</b> interface.
* Change Name Interface from drop-down list, select <b>VPLS</b> interface.
*Enable OSPF Interface on check bar.
*Enable OSPF Interface on check bar.
*Press Edit and state Cost, Hello Interval, Router Dead Interval and Retransmit.
*Press Edit and state Cost, Hello Interval, Router Dead Interval and Retransmit.
*Press Save & Apply.
*Press Save & Apply.
[[File:OSPF via VPLS and ZerotierVPN OSPF Interface add.png]]
==Configure OSPF Area==
==Configure OSPF Area==
[[File:OSPF via VPLS and ZerotierVPN OSPF AREA Template.png|973x973px]]
[[File:OSPF via VPLS and ZerotierVPN OSPF AREA Template.png]]
Create OSPF Area, and configure him number.
Create OSPF Area, and configure him number.
[[File:OSPF via VPLS and ZerotierVPN OSPF AREA SET.png|973x973px]]
[[File:OSPF via VPLS and ZerotierVPN OSPF AREA SET.png]]
==Configure OSPF Networks==
==Configure OSPF Networks==