Template:Networking rutos manual wan: Difference between revisions

From Teltonika Networks Wiki
VisualWikitext
No edit summary
 
(12 intermediate revisions by 4 users not shown)
Line 74: Line 74:
     </tr>
     </tr>
</table>
</table>
  | </table>
  |}}
}}


To begin configuring an interface, click the 'Edit' button on the right side of the interface:
To begin configuring an interface, click the 'Edit' button on the right side of the interface:
Line 238: Line 237:
     <tr>
     <tr>
     <td>PDP Type</td>
     <td>PDP Type</td>
         <td>IPv4 <nowiki>|</nowiki> IPv6 <nowiki>|</nowiki> IPv4/IPv6; default: <b>IPv4</b></td>
         <td>IPv4 <nowiki>|</nowiki> IPv6 <nowiki>|</nowiki> IPv4/IPv6; default: <b>IPv4/IPv6</b></td>
         <td>Specifies what of address will be requested from the operator.</td>
         <td>Specifies what of address will be requested from the operator.</td>
     </tr>  
     </tr>  
Line 389: Line 388:
             </ul>
             </ul>
         </td>
         </td>
    </tr>
     <tr>
     <tr>
     <td>Subnet selection</td>
     <td>Subnet selection</td>
Line 440: Line 440:
         <td>Specifies the MAC address of the device that will receive the mobile interface's IP address in Bridge or Passthrough mode.<br><b>Note:</b> this field only becomes visible when using Bridge or Passthrough mode.</td>
         <td>Specifies the MAC address of the device that will receive the mobile interface's IP address in Bridge or Passthrough mode.<br><b>Note:</b> this field only becomes visible when using Bridge or Passthrough mode.</td>
     </tr>
     </tr>
</table>|}}
</table>


{{#switch: {{{series}}}
{{#switch: {{{series}}}
Line 460: Line 460:
----
----
{{{name}}} supports Multiple PDN feature in order to establish connections to multiple mobile networks using a single SIM card. You can find a configuration example [[Multi-APN|here]].
{{{name}}} supports Multiple PDN feature in order to establish connections to multiple mobile networks using a single SIM card. You can find a configuration example [[Multi-APN|here]].
}}
}}|}}


===IPv6 Settings===
===IPv6 Settings===
Line 571: Line 571:
<b>Advanced Settings</b> information for <b>Static</b> protocol is provided in the table below.
<b>Advanced Settings</b> information for <b>Static</b> protocol is provided in the table below.


[[File:Networking_rutos_manual_wan_configuration_advanced_settings_static.png|border|class=tlt-border]]
[[File:Networking_rutos_manual_wan_configuration_advanced_settings_static_v2.png|border|class=tlt-border]]


<table class="nd-mantable">
<table class="nd-mantable">
Line 586: Line 586:
     <tr>
     <tr>
         <td>Use gateway metric</td>
         <td>Use gateway metric</td>
         <td>integer; default: <b>3</b></td>
         <td>integer [0..4294967295]; default: <b>3</b></td>
         <td>A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).</td>
         <td>A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).</td>
     </tr>
     </tr>
Line 671: Line 671:
     <tr>
     <tr>
         <td>Use gateway metric</td>
         <td>Use gateway metric</td>
         <td>integer; default: <b>none</b></td>
         <td>integer[0..4294967295]; default: <b>none</b></td>
         <td>A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).</td>
         <td>A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).</td>
     </tr>
     </tr>
Line 734: Line 734:
     <tr>
     <tr>
         <td>Use gateway metric</td>
         <td>Use gateway metric</td>
         <td>integer; default: <b>2</b></td>
         <td>integer[0..4294967295]; default: <b>2</b></td>
         <td>The configuration by default generates a routing table entry. In this field you can alter the metric of that entry. Lower metric means higher priority.</td>
         <td>The configuration by default generates a routing table entry. In this field you can alter the metric of that entry. Lower metric means higher priority.</td>
     </tr>
     </tr>
Line 793: Line 793:
     <tr>
     <tr>
         <td>Use gateway metric</td>
         <td>Use gateway metric</td>
         <td>integer; default: <b>none</b></td>
         <td>integer[0..4294967295]; default: <b>none</b></td>
         <td>A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).</td>
         <td>A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).</td>
     </tr>
     </tr>
Line 848: Line 848:
<b>Advanced Settings</b> information for <b>Mobile</b> protocol is provided in the table below.
<b>Advanced Settings</b> information for <b>Mobile</b> protocol is provided in the table below.


[[File:Networking_rutos_manual_wan_configuration_advanced_settings_mobile_v2.png|border|class=tlt-border]]
{{#switch: {{{name}}} | RUTM50 | RUTX50 | TRB500=
 
[[File:Networking_rutos_manual_wan_configuration_advanced_settings_mobile_v3.png|border|class=tlt-border]]
| #default=
[[File:Networking_rutos_manual_wan_configuration_advanced_settings_mobile_v2.png|border|class=tlt-border]]}}


<table class="nd-mantable">
<table class="nd-mantable">
Line 861: Line 865:
         <td>Specifies whether interface settings (IP, route, gateway) are assigned to the interface regardless of the link being active or only after the link has become active.</td>
         <td>Specifies whether interface settings (IP, route, gateway) are assigned to the interface regardless of the link being active or only after the link has become active.</td>
     </tr>
     </tr>
    {{#switch: {{{name}}} | RUTM50 | RUTX50 | TRB500=
    <tr>
        <td>Framed routing</td>
        <td>off {{!}} on; default: <b>off</b></td>
        <td>Allows static routes to be set up for subscribers, enabling connectivity from external networks to IP networks behind a user equipment.</td>
    </tr>
    | #default=}}
     <tr>
     <tr>
         <td>Use gateway metric</td>
         <td>Use gateway metric</td>
         <td>integer; default: <b>none</b></td>
         <td>integer[0..4294967295]; default: <b>none</b></td>
         <td>A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).</td>
         <td>A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).</td>
     </tr>
     </tr>
Line 913: Line 924:
More firewall zone settings can be configured from the Network → Firewall → General Settings → [[{{{name}}}_Firewall#Zones|Zones]] section.
More firewall zone settings can be configured from the Network → Firewall → General Settings → [[{{{name}}}_Firewall#Zones|Zones]] section.


[[File:Networking_rutos_manual_wan_configuration_firewall_settings.png|border|class=tlt-border]]
[[File:Networking_rutos_manual_wan_configuration_firewall_settings_v2.png|border|class=tlt-border]]


<table class="nd-mantable">
<table class="nd-mantable">
Line 935: Line 946:
<i>In order to view the Mobile Data Limit section, the interface <b>protocol must be set to Mobile</b>.</i>
<i>In order to view the Mobile Data Limit section, the interface <b>protocol must be set to Mobile</b>.</i>


[[File:Networking_rutos_manual_wan_configuration_mobile_mobile_data_limit.png|border|class=tlt-border]]
[[File:Networking_rutos_manual_wan_configuration_mobile_mobile_data_limit_v3.png|border|class=tlt-border]]


<table class="nd-mantable">
<table class="nd-mantable">
Line 953: Line 964:
       <td>The amount of data that is allowed to be downloaded over the specified period of time. When the limit is reached, the device will no longer be able to establish a data connection until the period is over or the data limit is reset.</td>
       <td>The amount of data that is allowed to be downloaded over the specified period of time. When the limit is reached, the device will no longer be able to establish a data connection until the period is over or the data limit is reset.</td>
     <tr>
     <tr>
     <td>Period</td>
     <td>Reset period</td>
         <td>Month <nowiki>|</nowiki> Week <nowiki>|</nowiki> Day; default: <b>Day</b></td>
         <td>Month <nowiki>|</nowiki> Week <nowiki>|</nowiki> Day; default: <b>Day</b></td>
         <td>Data limit period after which the data counter is reset on the specified <i>Start day</i>.</td>
         <td>Data limit period after which the data counter is reset on the specified <i>Start day</i>.</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Start day <nowiki>|</nowiki> Start hour</td>
     <td>Reset time <nowiki>|</nowiki> Reset day</td>
         <td>day [1..31] <nowiki>|</nowiki> day [Monday..Sunday] {{!}} hour [1..24]; default: <b>hour 0</b></td>
         <td>day [1..31] <nowiki>|</nowiki> day [Monday..Sunday] {{!}} hour [1..24]; default: <b>hour 0</b></td>
       <td>Specifies when the period of counting data usage should begin. After the period is over, the limit is reset and the count begins over again.</td>
       <td>Specifies when the period of counting data usage should begin. After the period is over, the limit is reset and the count begins over again.</td>
Line 964: Line 975:
     <tr>
     <tr>
       <td>Enable SMS warning</td>
       <td>Enable SMS warning</td>
       <td>off <nowiki>|</nowiki> on; default: <b>off</b></td>
       <td>off <nowiki>|</nowiki> <span style="color:blue">on</span>; default: <b>off</b></td>
       <td>Turns SMS warning on or off. When turned on and configured, sends an SMS message to a specified number after the SIM card uses a specified amount of data.</td>
       <td>Turns SMS warning on or off. When turned on and configured, sends an SMS message to a specified number after the SIM card uses a specified amount of data.</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Data limit* (MB)</td>
       <td><span style="color:blue">Warning threshold* (MB) (%)</span></td>
       <td>integer; default: <b>none</b></td>
       <td><ul><li>MB - positive integer; default: <b>none</b></li> <li>% - interger [1..100]; default: <b>none</b></li></ul></td>
       <td>The received data limit before sending an SMS warning. After reaching using the the amount of data specified in this field, the router will send an SMS warning message to the specified phone number.</td>
       <td>Send warning SMS message after threshold in MB is reached. Warning threshold cannot be higher than data limit!</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Phone number</td>
     <td><span style="color:blue">Phone number</span></td>
         <td>phone number; default: <b>none</b></td>
         <td>phone number; default: <b>none</b></td>
         <td>Recipient's phone numbers.</td>
         <td>A phone number to send warning SMS message to.</td>
     </tr>
     </tr>
     <tr>
     <tr>

Latest revision as of 13:30, 4 October 2024

The information in this page is updated in accordance with firmware version .


Summary

The WAN page is used to to set up WAN network interfaces, which are used to connect device with external networks.

This manual page provides an overview of the WAN windows in {{{name}}} devices.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Advanced" button, located at the top of the WebUI.

WAN

The WAN section displays WAN network interfaces currently existing on this device.

[[File:Networking_rutos_manual_wan_mobile_{{{mobile}}}_dualsim_{{{dualsim}}}_dualmodem_{{{dualmodem}}}_wired_{{{wired}}}_v3.png|border|class=tlt-border]]

From here you can turn the interfaces, enable/disable interface's failover, create interfaces, change their priority* or enter an interface's configuration page.

* You can change the priority by dragging and dropping an interface to another position. Moving an interface changes its metric value in the configuration file. Interfaces that are higher on the list have greater priority.

If you hover mouse over the question mark global IPv6 addresses and IPv6 prefix delegation will be displayed.

Interface configuration

This section provides information on network interface configuration. There are {{{no_of_if}}} main types of interfaces on the device:

Different types of interfaces can be configured under different protocols:

To begin configuring an interface, click the 'Edit' button on the right side of the interface:

General Setup

The General Setup section is used to configure the protocol of an interface and all the different parameters that go along with each protocol. If None protocol is chosen, all other interface settings will be ignored. The following sections are different for each protocol.

General Settings: Static

The static protocol uses a predefined manual configuration instead of obtaining parameters automatically via a DHCP lease.

Static DHCP DHCPv6 PPPoE
Field Value Description
Enable on | off; default: on Enable interface.
IPv4 address ip4; default: none The IPv4 address interface of this interface. An IP address identifies a device on a network and allows it to communicate with other devices.
IPv4 netmask netmask; default: 255.255.255.0 The IPv4 netmask of this interface. A netmask is used to define how "large" a network is by specifying which part of the IP address denotes the network and which part denotes a device.
IPv4 gateway ip4; default: none The IPv4 gateway address used by this interface. An interface's default gateway is the default address through which all outgoing traffic is directed.
IPv4 broadcast ip4; default: none The IPv4 broadcast address used by this interface. IP broadcasts are used by BOOTP and DHCP clients to find and send requests to their respective servers.
DNS servers ip4; default: none DNS server addresses that this interface will use. If left empty, DNS servers are assigned automatically. To see what DNS servers are currently used, you can check the contents of the /tmp/resolv.conf.auto file.

General Settings: DHCP

The DHCP protocol is used to set up an interface which obtains its configuration parameters automatically via a DHCP lease.

Field Value Description
Enable on | off; default: on Enable interface.
Hostname to send when requesting DHCP string; default: none A hostname for this interface used to identify this machine on the DHCP server.

General Settings: DHCPv6

The DHCPv6 protocol is used to set up an IPv6 interface which obtains its configuration parameters automatically via a DHCP lease.

Field Value Description
Enable on | off; default: on Enable interface.

General Settings: PPPoE

The PPPoE protocol is used to set up a PPP (Point-to-Point Protocol) connection over the Ethernet port.

Field Value Description
Enable on | off; default: on Enable interface.
PAP/CHAP username string; default: none Username used in PAP/CHAP authentication.
PAP/CHAP password string; default: none Password used in PAP/CHAP authentication.
Access Concentrator string; default: none The Access Concentrator to connect to. ISPs used Access Concentrators to route their PPPoE connections. Usually, the settings are received automatically, however in some cases it is required to specify the name for an Access Concentrator. Leave empty to detect Access Concentrators automatically.
Service name string; default: none The Service Name to connect to. Leave empty to detect Service name automatically.


IPv6 Settings

The IPv6 Settings section is used to set up some of the more specific and less frequently used interface parameters. This section is different for each protocol.

IPv6 Settings: Static

Advanced Settings information for Static protocol is provided in the table below.

Field Value Description
Delegate IPv6 prefixes off | on; default: on Enable downstream delegation of IPv6 prefixes available on this interface.
IPv6 assignment length Disabled | 64 | Custom; default: Disabled A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).
IPv6 address IPv6 addresses with or without mask prefix are accepted; default: none Assigns an IPv6 address for this interface. CIDR notation: address/prefix.
IPv6 gateway IPv6 addresses are accepted. E.g. ::0000:8a2e:0370:7334; default: none IPv6 default gateway.
IPv6 routed prefix IPv6 addresses with mask prefix are accepted E.g ::1/128; default: none Public prefix routed to this device for distribution to clients.
IPv6 suffix Allowed values: "eui64", "random", fixed value like "::1" or "::1:2"; default: none Optional. Allowed values: 'eui64', 'random', fixed value like '::1' or '::1:2'. When IPv6 prefix (like 'a:b:c:d::') is received from a delegating server, use the suffix (like '::1') to form the IPv6 address ('a:b:c:d::1') for the interface.

IPv6 Settings: DHCPv6

Advanced Settings information for DHCPv6 protocol is provided in the table below.

Field Value Description
Delegate IPv6 prefixes off | on; default: on Enable downstream delegation of IPv6 prefixes available on this interface.
Request IPv6-address try | force | disabled; default: try Defines the behaviour for requesting an address.
Request IPv6-prefix of length integer [0..64] | Automatic | disabled ; default: Automatic Defines how this will request a IPv6 ULA-Prefix length. If set to 'disabled' the interface will obtain a single IPv6 address without a subnet for routing.

IPv6 Settings: PPPoE

Advanced Settings information for PPPoE protocol is provided in the table below.

Field Value Description
Delegate IPv6 prefixes off | on; default: on Enable downstream delegation of IPv6 prefixes available on this interface.
Obtain IPv6 address Automatic | Disabled | Manual; default: Automatic Defines behaviour for obtaining an IPv6 address.

Advanced Settings

The Advanced Settings section is used to set up some of the more specific and less frequently used interface parameters. This section is different for each protocol.

Advanced Settings: Static

Advanced Settings information for Static protocol is provided in the table below.

Field Value Description
Force link off | on; default: on Specifies whether interface settings (IP, route, gateway) are assigned to the interface regardless of the link being active or only after the link has become active.
Use gateway metric integer [0..4294967295]; default: 3 A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).
Override MAC address mac; default: none When set, uses a user-defined MAC address for the interface instead of the default one.
Override MTU integer [1..9200]; default: none Changes the interface's allowed maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction.
  • Note: Interface(s): have mtu lower than 1280 it will make all interfaces on same physical interface no longer support IPv4.
  • Note: Interface(s): have mtu lower than 576 it will make all interfaces on same physical interface no longer support DHCP.
IP4 table integer [0..99999999]; default: none ID of the routing table in [[{{{name}}}_Routing#Routing_Tables|Routing tables]] page.

Advanced Settings: DHCP

Advanced Settings information for DHCP protocol is provided in the table below.

Field Value Description
Force link off | on; default: off Specifies whether interface settings (IP, route, gateway) are assigned to the interface regardless of the link being active or only after the link has become active.
Use broadcast flag off | on; default: off Required for certain ISPs. For example, Charter with DOCSIS 3.
Use default gateway off | on; default: on When checked, creates a default route for the interface.
Use gateway metric integer[0..4294967295]; default: none A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).
Use custom DNS servers ip4; default: none Specifies custom DNS servers. If left empty, DNS servers advertised by peer are used.
Client ID to send when requesting DHCP string; default: none Client ID which will be sent when requesting a DHCP lease.
Vendor Class to send when requesting DHCP string; default: none Vendor class which will be sent when requesting a DHCP lease.
Override MAC address mac; default: none When set, uses a user-defined MAC address for the interface instead of the default one.
Override MTU integer [1..9200]; default: none Changes the interfaces allowed maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction.
  • Note: Interface(s): have mtu lower than 1280 it will make all interfaces on same physical interface no longer support IPv4.
  • Note: Interface(s): have mtu lower than 576 it will make all interfaces on same physical interface no longer support DHCP.
IP4 table integer [0..99999999]; default: none ID of the routing table in [[{{{name}}}_Routing#Routing_Tables|Routing tables]] page.

Advanced Settings: DHCPv6

Advanced Settings information for DHCPv6 protocol is provided in the table below.

Field Value Description
Force link off | on; default: off Specifies whether interface settings (IP, route, gateway) are assigned to the interface regardless of the link being active or only after the link has become active.
Use default gateway off | on; default: on When checked, creates a default route for the interface.
Use gateway metric integer[0..4294967295]; default: 2 The configuration by default generates a routing table entry. In this field you can alter the metric of that entry. Lower metric means higher priority.
Use custom DNS servers ip4; default: none Specifies custom DNS servers. If left empty, DNS servers advertised by peer are used.
Client ID to send when requesting DHCP string; default: none Client ID which will be sent when requesting a DHCP lease.
Override MAC address mac; default: none When set, uses a user-defined MAC address for the interface instead of the default one.
Override MTU integer [1..9200]; default: none Changes the interface's allowed maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction.
  • Note: Interface(s): have mtu lower than 1280 it will make all interfaces on same physical interface no longer support IPv4.
  • Note: Interface(s): have mtu lower than 576 it will make all interfaces on same physical interface no longer support DHCP.
IP6 table integer [0..2^46]; default: none ID of the routing table in [[{{{name}}}_Routing#Routing_Tables|Routing tables]] page.

Advanced Settings: PPPoE

Advanced Settings information for PPPoE protocol is provided in the table below.

Field Value Description
Force link off | on; default: off Specifies whether interface settings (IP, route, gateway) are assigned to the interface regardless of the link being active or only after the link has become active.
Use default gateway off | on; default: on When checked, creates a default route for the interface.
Use gateway metric integer[0..4294967295]; default: none A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority).
Use custom DNS servers ip4; default: none Specifies custom DNS servers. If left empty, DNS servers advertised by peer are used.
VLAN tag value integer [0..7]; default: none VLAN tag value.
VLAN priority integer [0..4095]; default: none VLAN priority.
LCP echo failure threshold integer; default: none Presumes peer to be dead after given amount of LCP echo failures. Leave it at 0 to ignore failures.
LCP echo interval integer; default: none Sends LCP echo requests at the given interval in seconds. This function is only effective in conjunction with failure threshold.
Host-Uniq tag content raw hex-encoded bytes; default: none Leave empty unless your ISP require this.
Inactivity timeout mac; default: none Close inactive connection after the given amount of seconds. Leave it at 0 to persist connection.
Override MTU integer [1..1500]; default: none Maximum Transmission Unit (MTU) – specifies the largest possible size of a data packet.
IP4 table integer [0..99999999]; default: none ID of the routing table in [[{{{name}}}_Routing#Routing_Tables|Routing tables]] page.


Physical Settings

The Physical Settings section is used to create associations with physical interfaces and bridge network interfaces.

Field Value Description
Bridge interfaces off | on; default: off Bridges physical interfaces specified in this configuration.
Interface network interface(s); default: wan physical interface Ties this network interface to physical device interfaces such as Ethernet.

Firewall Settings

The Firewall Settings section is used to specify to which firewall zone if any this interface belongs. Assigning an interface to a zone may provide easier configuration of firewall rules. For example, instead of configuring separate rules for each WAN interface, you can add all WAN interfaces into a single firewall zone and make the rule apply to that zone instead.

More firewall zone settings can be configured from the Network → Firewall → General Settings → [[{{{name}}}_Firewall#Zones|Zones]] section.

Field Value Description
Create / Assign firewall-zone firewall zone; default: none Assigns this interface to the specified firewall zone.


[[Category:{{{name}}} Network section]]

Retrieved from "https://wiki.teltonika-networks.com/index.php?title=Template:Networking_rutos_manual_wan&oldid=133683"