Template:Networking rutos manual leds: Difference between revisions

From Teltonika Networks Wiki
No edit summary
Tag: Reverted
No edit summary
 
(9 intermediate revisions by the same user not shown)
Line 116: Line 116:


{{#switch: {{{eth_leds}}}  
{{#switch: {{{eth_leds}}}  
  | 1 =The <b>Ethernet port LEDs</b> are located on the device's front panel, under each respective Ethernet port.
  | 1 = The <b>Ethernet port LEDs</b> are located on the device's front panel, under each respective Ethernet port.


[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]]
[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]]
Line 142: Line 142:
     </tr>-->
     </tr>-->
</table>
</table>
  | 2=There are two <b>LEDs</b> located at the top of each <b>Ethernet port</b>.
  | 2 = There are two <b>LEDs</b> located at the top of each <b>Ethernet port</b>.


[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]]
[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]]
Line 556: Line 556:
The Mobile signal strength LEDs can also be used as a <b>time indicator for holding the reset button</b>. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a <b>User's default configuration reset</b> and 12 seconds (by default) to initiate a <b>Factory reset</b>. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a <b>Factory reset</b>. If the button was held down longer than 20 seconds (by default) no action will be taken.  
The Mobile signal strength LEDs can also be used as a <b>time indicator for holding the reset button</b>. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a <b>User's default configuration reset</b> and 12 seconds (by default) to initiate a <b>Factory reset</b>. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a <b>Factory reset</b>. If the button was held down longer than 20 seconds (by default) no action will be taken.  


While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with <b>{{{name}}}</b>, when all {{#ifeq: {{{name}}} | RUTX12 | {{#expr: {{{mobile_leds}}} * 2}} | {{{mobile_leds}}}}} Mobile signal strength LEDs are lit up, they represent that {{#ifeq: {{{name}}} | RUTX12 | {{#expr: {{{mobile_leds}}} * 4}} | {{#expr: {{{mobile_leds}}} * 2}} }} (LED number multiplied by 2) seconds have passed since you pressed down on the reset button.
While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with <b>{{{name}}}</b>, when all {{#switch: {{{name}}} | RUTX12 | RUTM52 = {{#expr: {{{mobile_leds}}} * 2}} | #default = {{{mobile_leds}}}}} Mobile signal strength LEDs are lit up, they represent that {{#switch: {{{name}}} | RUTX12 | RUTM52 = {{#expr: {{{mobile_leds}}} * 4}} | #default = {{#expr: {{{mobile_leds}}} * 2}}}} (LED number multiplied by 2) seconds have passed since you pressed down on the reset button.


After releasing the button at one of the reset periods, all {{#ifeq: {{{name}}} | RUTX12 | {{#expr: {{{mobile_leds}}} * 2}} | {{{mobile_leds}}}}} LEDs will start blinking every 1 second. This signifies that the router <b>has begun the reset</b>.  
After releasing the button at one of the reset periods, all {{#switch: {{{name}}} | RUTX12 | RUTM52 = {{#expr: {{{mobile_leds}}} * 2}} | #default = {{{mobile_leds}}}}} LEDs will start blinking every 1 second. This signifies that the router <b>has begun the reset</b>.  
|}}}}
}}|}}


[[Category:{{{name}}} Manual]]
[[Category:{{{name}}} Manual]]

Latest revision as of 12:25, 13 November 2024

This page contains information the different types of LEDs and their behaviour on a {{{name}}} device.

Power LED

The power LED is located on the bottom left corner of the front panel, just under the power connector.

[[File:Networking_{{{name}}}_manual_leds_power_led.png|500px]]

It indicates whether the device is powered on or not.

State Description
M LED turned on Device is powered over the Main power connector.
M LED turned off Device is not powered over the Main power connector.
R LED turned on Device is powered over the Reserve power connector.
R LED turned off Device is not powered over the Reserve power connector.

[[Category:{{{name}}} Manual]]