RUTM59 Devices

The information in this page is updated in accordance with firmware version RUTM_R_00.07.11.3.

VXLAN

Virtual Extensible LAN is a tunneling interface protocol (VXLAN), which allows VXLAN layer 2 virtualization over layer 3 network. VXLAN establishes a logical tunnel between the source and destination network devices, through which it uses MAC-in-UDP encapsulation for packets. In addition, it helps customer sites to configure layer2 VPN.

Note: VXLAN is additional software that can be installed from the System → Package Manager page.

---

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Advanced" button, located at the top of the WebUI.

Device configuration (VXLAN)

The Device configuration section is used to set up VXLAN devices.

To add a new device - select 'VXLAN' and click 'Add' button:

After clicking 'Add' you will be redirected to the newly added VXLAN device configuration page.

Configuration (VXLAN)

Field	Value	Description
Name	string; default: vxlan1	Name of the device.
MAC address	mac; default: empty	Override MAC address of the device. If not set, the device's MAC address will be used.
MTU	integer [98..9000]; default: empty	Sets the maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction.
VNI	integer [1..16777215]; default: 1	VXLAN network identifier.
PORT	integer [1..65535]; default: 4789	VXLAN network identifier.
Local address	ip; default: none	Sets the local source IP address for VXLAN tunneling.
Remote address	ip; default: none	Specifies the multicast group or remote IP address used for VXLAN tunneling.
Ageing	integer [1..4294967295]; default: empty	Specifies the lifetime in seconds of FDB entries learnt by the kernel.
Max FDB entries	integer [1..4294967295]; default: empty	Specifies the maximum number of FDB entries.
IPv4 checksum	off | on; default: off	Specifies if UDP checksum is calculated for transmitted packets over IPv4.
Learning	off | on; default: off	Enables or disables MAC learning for VXLAN.
Proxy	off | on; default: off	Enables or disables ARP proxy for VXLAN.
RSC	off | on; default: off	Specifies if route short circuit is turned on.
L2miss	off | on; default: off	Specifies if netlink LLADDR miss notifications are generated.
L3miss	off | on; default: off	Specifies if netlink IP ADDR miss notifications are generated.
IPv6 TX checksum	off | on; default: off	Enables or disables UDP checksum calculation for transmitted packets over IPv6.
IPv6 RX checksum	off | on; default: off	Allow incoming UDP packets over IPv6 with zero checksum field.

Bridge

A network Bridge is a computer networking device that creates a single, aggregate network from multiple communication networks or network segments. This function is called network bridging. Bridging is distinct from routing. Routing allows multiple networks to communicate independently and yet remain separate, whereas bridging connects two separate networks as if they were a single network.

Device configuration (Bridge)

The Device configuration section is used to set up Bridge devices.

To add a new device - select 'Bridge' and click 'Add' button:

After clicking 'Add' you will be redirected to the newly added Bridge device configuration page.

Configuration (Bridge)

Field	Value	Description
Name	string; default: bridge1	Name of the device.
MAC address	mac; default: empty	Override MAC address of the device. If not set, the device's MAC address will be used.
MTU	integer [98..2030]; default: empty	Sets the maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction.
Ports	select; default: none	Specifies the wired ports to attach to this bridge.
Enable IGMP	off | on; default: off	Enables IGMP snooping on this bridge.
Enable STP	off | on; default: off	Enables the Spanning Tree Protocol on this bridge.
Priority	integer [0..65535]; default: none	Bridge Priority. Lowest priority bridge becomes the Root of the Spanning Tree; most switches default to 32768.
Ageing time	integer [10..1000000]; default: none	Timeout in seconds for learned MAC addresses in the forwarding database.
Hello time	integer [1..10]; default: none	Number of seconds between transmissions of configuration BPDUs.
Forward delay	integer [2..30]; default: none	How long an STP bridge port remains in the listening and learning states before transitioning to the forwarding state.
Max age	integer [6..40]; default: none	Maximum expected arrival time of hello bridge protocol data units (BPDUs).