Mobile data connection troubleshooting: Difference between revisions
No edit summary |
m (Protected "Mobile data connection troubleshooting" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))) |
||
| (19 intermediate revisions by one other user not shown) | |||
| Line 18: | Line 18: | ||
+CREG: 1,"008B","012CD17",7 | +CREG: 1,"008B","012CD17",7 | ||
... | ... | ||
--- | ---- | ||
* You probably won't see anything when you type commands, and that’s because the screen echo may be disabled. '''ATE1''' command will enable it so that you can see what you write. | * You probably won't see anything when you type commands, and that’s because the screen echo may be disabled. '''ATE1''' command will enable it so that you can see what you write. | ||
... | ... | ||
ATE1 | ATE1 | ||
OK | OK | ||
... | |||
---- | |||
* Use commands '''AT+QCSQ=0''' and '''AT+CREG=0''' to stop showing unnecessary output: | |||
... | |||
at+qcsq=0 | at+qcsq=0 | ||
OK | OK | ||
| Line 28: | Line 32: | ||
OK | OK | ||
... | ... | ||
--- | ---- | ||
* Check communication (wait for the module to respond '''OK'''): | * Check communication (wait for the module to respond '''OK'''): | ||
... | ... | ||
| Line 34: | Line 38: | ||
OK | OK | ||
... | ... | ||
--- | ---- | ||
==Debugging process== | ==Debugging process== | ||
* If PIN is required, initialize modem with your PIN code: | * If PIN is required, initialize modem with your PIN code: | ||
| Line 40: | Line 45: | ||
AT+CPIN="xxxx" | AT+CPIN="xxxx" | ||
... | ... | ||
--- | ---- | ||
* Use command '''AT+CPIN''' to query SIM card status: | * Use command '''AT+CPIN''' to query SIM card status: | ||
... | ... | ||
| Line 46: | Line 51: | ||
+CPIN: READY | +CPIN: READY | ||
... | ... | ||
'''Note:''' reboot the module if it fails to identify SIM | |||
'''Note:''' | ---- | ||
--- | *Use command '''AT+CREG''' to check GSM connection: | ||
* Use command '''AT+CREG''' to check GSM connection: | |||
... | ... | ||
AT+CREG? | AT+CREG? | ||
| Line 55: | Line 59: | ||
OK | OK | ||
... | ... | ||
'''Note:''' OK means that the module has registered on CS domain service | '''Note:''' OK means that the module has registered on CS domain service | ||
--- | ---- | ||
* Use command '''AT+CGREG''' to check PS Service: | * Use command '''AT+CGREG''' to check PS Service: | ||
... | ... | ||
| Line 64: | Line 67: | ||
OK | OK | ||
... | ... | ||
'''Note:''' OK means that the module has registered in UMTS/LTE network | |||
---- | |||
* Use command '''AT+QICSGP''' to configure APN, user name, password and auth type: | |||
AT+QICSGP=<contextID>[,<context_type>,<APN>[,<username>,<password>)[,<authentication>]]] | |||
''<context type>'' The protocol type (1 – IPV4; 2 – IPv6); | |||
''<context id>'' The range is 1-16; | |||
''<authentication>'' The authentication methods (0 – NONE; 1 – PAP; 2 – CHAP; 3-PAP or CHAP). | |||
'''Note:''' | Example: '''AT+QICSGP=1,1,"APN_Name","","",1''' | ||
--- | ... | ||
* | AT+QICSGP=1,1"bangapro","","",1 | ||
OK | |||
... | |||
---- | |||
* Use command '''AT+QIACT=<contextID>''' to activate a PDP context: | |||
... | |||
AT+QIACT=1 | |||
OK | |||
... | |||
---- | |||
* Use command '''AT+QIACT?''' to query IP Address of the PDP context: | |||
... | |||
AT+QIACT? | |||
+QIACT: 1,1,1,"88.77.66.55" | |||
OK | |||
... | |||
'''Note:''' try and activate a PDP context a few times. If failed, then reboot the module. | |||
---- | |||
* Use command '''AT+QIOPEN''' to open connection: | |||
... | |||
AT+QIOPEN | |||
OK | |||
... | |||
'''Note:''' if failed – deactivate PDP context - use command '''AT+QIDEACT=<context ID>''' to deactivate PDP context. | |||
---- | |||
* Use command '''AT+QPING''' to ping a Remote Server: | |||
... | ... | ||
AT+ | AT+QPING=1,"8.8.8.8" | ||
OK | |||
+QPING: 0,"8.8.8.8",32,54,255 | |||
+QPING: 0,"8.8.8.8",32,30,255 | |||
+QPING: 0,"8.8.8.8",32,35,255 | |||
+QPING: 0,"8.8.8.8",32,34,255 | |||
+QPING: 0,4,4,0,30,54,37 | |||
... | ... | ||
''1'' –The context ID. The range is 1-16; | |||
''8.8.8.8'' - The host address in string type. | |||
'''Note:''' if ping a remote server successfully, response is '''OK''' (means that the module works properly). If there is any error, response is '''ERROR''' (means the problem is in the module). | |||
==Example for the provided configuration== | |||
... | |||
root@Teltonika:~# ifdown ppp | |||
root@Teltonika:~# /etc/init.d/gsmd stop | |||
root@Teltonika:~# microcom /dev/modem_cmd | |||
+QCSQ: "LTE",47,-75,166,-10 | |||
+QCSQ: "LTE",47,-75,161,-10 | |||
+QCSQ: "LTE",47,-75,156,-10 | |||
+CREG: 1,"008B","012CD17",7 | |||
AT+QCSQ=0 | |||
OK | |||
+CREG: 1,"008B","012CD0D",7 | |||
+CREG: 1,"008B","012CD17",7 | |||
AT+CREG=0 | |||
OK | |||
AT | |||
OK | |||
... | |||
... | |||
AT+CPIN? | |||
+CPIN: READY | |||
OK | |||
AT+CREG | |||
OK | |||
AT+CREG? | |||
+CREG: 0,1 | |||
OK | |||
AT+CREG | |||
OK | |||
AT+CGREG? | |||
+CGREG: 0,1 | |||
OK | |||
AT+QICSGP=1,1"bangapro","","",1 | |||
OK | |||
AT+QIACT=1 | |||
OK | |||
AT+QIACT? | |||
+QIACT: 1,1,1,"88.77.66.55" | |||
OK | |||
... | |||
... | |||
AT+QIOPEN | |||
OK | |||
AT+QPING=1,"8.8.8.8" | |||
OK | |||
+QPING: 0,"8.8.8.8",32,54,255 | |||
+QPING: 0,"8.8.8.8",32,30,255 | |||
+QPING: 0,"8.8.8.8",32,35,255 | |||
+QPING: 0,"8.8.8.8",32,34,255 | |||
+QPING: 0,4,4,0,30,54,37 | |||
... | |||
Latest revision as of 14:59, 22 May 2020
Summary
This is a quick guide to help in the debugging process of a router if encounters issues with mobile data connection.
Preparation
- First, to establish a data connection only through mobile module on RUT, you need connect to router via CLI/SSH (use SSH software such as PuTTY client):
CLI/SSH username: root CLI/SSH password: <your router’s password>
- Connect to mobile module of the router:
... root@Teltonika:~# ifdown ppp root@Teltonika:~# /etc/init.d/gsmd stop root@Teltonika:~# microcom /dev/modem_cmd +QCSQ: "LTE",47,-75,166,-10 +QCSQ: "LTE",47,-75,161,-10 +CREG: 1,"008B","012CD17",7 ...
- You probably won't see anything when you type commands, and that’s because the screen echo may be disabled. ATE1 command will enable it so that you can see what you write.
... ATE1 OK ...
- Use commands AT+QCSQ=0 and AT+CREG=0 to stop showing unnecessary output:
... at+qcsq=0 OK at+creg=0 OK ...
- Check communication (wait for the module to respond OK):
... AT OK ...
Debugging process
- If PIN is required, initialize modem with your PIN code:
... AT+CPIN="xxxx" ...
- Use command AT+CPIN to query SIM card status:
... AT+CPIN? +CPIN: READY ...
Note: reboot the module if it fails to identify SIM
- Use command AT+CREG to check GSM connection:
... AT+CREG? +CREG: 0,1 OK ...
Note: OK means that the module has registered on CS domain service
- Use command AT+CGREG to check PS Service:
... AT+CGREG? +CGREG: 0,1 OK ...
Note: OK means that the module has registered in UMTS/LTE network
- Use command AT+QICSGP to configure APN, user name, password and auth type:
AT+QICSGP=<contextID>[,<context_type>,<APN>[,<username>,<password>)[,<authentication>]]]
<context type> The protocol type (1 – IPV4; 2 – IPv6);
<context id> The range is 1-16;
<authentication> The authentication methods (0 – NONE; 1 – PAP; 2 – CHAP; 3-PAP or CHAP).
Example: AT+QICSGP=1,1,"APN_Name","","",1
... AT+QICSGP=1,1"bangapro","","",1 OK ...
- Use command AT+QIACT=<contextID> to activate a PDP context:
... AT+QIACT=1 OK ...
- Use command AT+QIACT? to query IP Address of the PDP context:
... AT+QIACT? +QIACT: 1,1,1,"88.77.66.55" OK ...
Note: try and activate a PDP context a few times. If failed, then reboot the module.
- Use command AT+QIOPEN to open connection:
... AT+QIOPEN OK ...
Note: if failed – deactivate PDP context - use command AT+QIDEACT=<context ID> to deactivate PDP context.
- Use command AT+QPING to ping a Remote Server:
... AT+QPING=1,"8.8.8.8" OK +QPING: 0,"8.8.8.8",32,54,255 +QPING: 0,"8.8.8.8",32,30,255 +QPING: 0,"8.8.8.8",32,35,255 +QPING: 0,"8.8.8.8",32,34,255 +QPING: 0,4,4,0,30,54,37 ...
1 –The context ID. The range is 1-16;
8.8.8.8 - The host address in string type.
Note: if ping a remote server successfully, response is OK (means that the module works properly). If there is any error, response is ERROR (means the problem is in the module).
Example for the provided configuration
... root@Teltonika:~# ifdown ppp root@Teltonika:~# /etc/init.d/gsmd stop root@Teltonika:~# microcom /dev/modem_cmd +QCSQ: "LTE",47,-75,166,-10 +QCSQ: "LTE",47,-75,161,-10 +QCSQ: "LTE",47,-75,156,-10 +CREG: 1,"008B","012CD17",7 AT+QCSQ=0 OK +CREG: 1,"008B","012CD0D",7 +CREG: 1,"008B","012CD17",7 AT+CREG=0 OK AT OK ...
... AT+CPIN? +CPIN: READY OK AT+CREG OK AT+CREG? +CREG: 0,1 OK AT+CREG OK AT+CGREG? +CGREG: 0,1 OK AT+QICSGP=1,1"bangapro","","",1 OK AT+QIACT=1 OK AT+QIACT? +QIACT: 1,1,1,"88.77.66.55" OK ...
... AT+QIOPEN OK AT+QPING=1,"8.8.8.8" OK +QPING: 0,"8.8.8.8",32,54,255 +QPING: 0,"8.8.8.8",32,30,255 +QPING: 0,"8.8.8.8",32,35,255 +QPING: 0,"8.8.8.8",32,34,255 +QPING: 0,4,4,0,30,54,37 ...