Difference between revisions of "Template:Networking rut955 manual modbus modbus tcp set parameters table"
Gytispieze (talk | contribs) |
|||
(5 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
<table class="nd-othertables"> | <table class="nd-othertables"> | ||
<tr> | <tr> | ||
− | <th width=" | + | <th width="300">value to set</th> |
− | <th width=" | + | <th width="140">register address</th> |
+ | <th width="140">register number</th> | ||
<th width="150">register value</th> | <th width="150">register value</th> | ||
<th width="466">description</th> | <th width="466">description</th> | ||
Line 9: | Line 10: | ||
<td>Hostname</td> | <td>Hostname</td> | ||
<td>7</td> | <td>7</td> | ||
+ | <td>8</td> | ||
<td>Hostname</td> | <td>Hostname</td> | ||
− | <td> | + | <td>Changes hostname</td> |
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Device name</td> | <td>Device name</td> | ||
<td>71</td> | <td>71</td> | ||
+ | <td>72</td> | ||
<td>Device name</td> | <td>Device name</td> | ||
− | <td> | + | <td>Changes device name</td> |
</tr> | </tr> | ||
− | |||
<tr> | <tr> | ||
<td>Digital output 1 (DOUT1) (ON/OFF<span class="asterisk">*</span>)</td> | <td>Digital output 1 (DOUT1) (ON/OFF<span class="asterisk">*</span>)</td> | ||
<td>201</td> | <td>201</td> | ||
− | <td>1 | + | <td>202</td> |
+ | <td>1 {{!}} 0</td> | ||
<td>Changes the state of the open collector (OC) output</td> | <td>Changes the state of the open collector (OC) output</td> | ||
</tr> | </tr> | ||
Line 28: | Line 31: | ||
<td>Digital output 2 (DOUT2) (ON/OFF<span class="asterisk">*</span>)</td> | <td>Digital output 2 (DOUT2) (ON/OFF<span class="asterisk">*</span>)</td> | ||
<td>202</td> | <td>202</td> | ||
− | <td>1 | + | <td>203</td> |
+ | <td>1 {{!}} 0</td> | ||
<td>Changes the state of the relay output</td> | <td>Changes the state of the relay output</td> | ||
</tr> | </tr> | ||
− | |||
− | |||
<tr> | <tr> | ||
<td>Switch WiFi (ON/OFF<span class="asterisk">*</span>)</td> | <td>Switch WiFi (ON/OFF<span class="asterisk">*</span>)</td> | ||
<td>203</td> | <td>203</td> | ||
+ | <td>204</td> | ||
<td>1 | 0</td> | <td>1 | 0</td> | ||
<td>Turns WiFi ON or OFF</td> | <td>Turns WiFi ON or OFF</td> | ||
Line 42: | Line 45: | ||
<td>Switch mobile data connection (ON/OFF<span class="asterisk">*</span>)</td> | <td>Switch mobile data connection (ON/OFF<span class="asterisk">*</span>)</td> | ||
<td>204</td> | <td>204</td> | ||
+ | <td>205</td> | ||
<td>1 | 0</td> | <td>1 | 0</td> | ||
<td>Turns mobile data connection ON or OFF</td> | <td>Turns mobile data connection ON or OFF</td> | ||
Line 48: | Line 52: | ||
<td>Switch SIM card</td> | <td>Switch SIM card</td> | ||
<td>205</td> | <td>205</td> | ||
+ | <td>206</td> | ||
<td>1 | 2 | 0</td> | <td>1 | 2 | 0</td> | ||
<td>Changes the active SIM card slot | <td>Changes the active SIM card slot | ||
Line 60: | Line 65: | ||
<td>Reboot</td> | <td>Reboot</td> | ||
<td>206</td> | <td>206</td> | ||
+ | <td>207</td> | ||
<td>1</td> | <td>1</td> | ||
<td>Reboots the router</td> | <td>Reboots the router</td> | ||
Line 66: | Line 72: | ||
<td>Change APN</td> | <td>Change APN</td> | ||
<td>207</td> | <td>207</td> | ||
+ | <td>208</td> | ||
<td>APN code</td> | <td>APN code</td> | ||
<td>Changes APN. <br> The number of input registers may vary depending on the length of the APN, but the very first byte of the set APN command denotes the number of the SIM card for which to set the APN. This byte should be set to: | <td>Changes APN. <br> The number of input registers may vary depending on the length of the APN, but the very first byte of the set APN command denotes the number of the SIM card for which to set the APN. This byte should be set to: | ||
Line 77: | Line 84: | ||
<td>Switch PIN4 state (ON/OFF<span class="asterisk">*</span>)</td> | <td>Switch PIN4 state (ON/OFF<span class="asterisk">*</span>)</td> | ||
<td>325</td> | <td>325</td> | ||
+ | <td>326</td> | ||
<td>1 | 0</td> | <td>1 | 0</td> | ||
<td>Turns PIN4 state ON or OFF</td> | <td>Turns PIN4 state ON or OFF</td> | ||
</tr> | </tr> | ||
</table> | </table> |
Latest revision as of 12:11, 28 December 2021
value to set | register address | register number | register value | description |
---|---|---|---|---|
Hostname | 7 | 8 | Hostname | Changes hostname |
Device name | 71 | 72 | Device name | Changes device name |
Digital output 1 (DOUT1) (ON/OFF*) | 201 | 202 | 1 | 0 | Changes the state of the open collector (OC) output |
Digital output 2 (DOUT2) (ON/OFF*) | 202 | 203 | 1 | 0 | Changes the state of the relay output |
Switch WiFi (ON/OFF*) | 203 | 204 | 1 | 0 | Turns WiFi ON or OFF |
Switch mobile data connection (ON/OFF*) | 204 | 205 | 1 | 0 | Turns mobile data connection ON or OFF |
Switch SIM card | 205 | 206 | 1 | 2 | 0 | Changes the active SIM card slot
|
Reboot | 206 | 207 | 1 | Reboots the router |
Change APN | 207 | 208 | APN code | Changes APN. The number of input registers may vary depending on the length of the APN, but the very first byte of the set APN command denotes the number of the SIM card for which to set the APN. This byte should be set to:
|
Switch PIN4 state (ON/OFF*) | 325 | 326 | 1 | 0 | Turns PIN4 state ON or OFF |