RUT360 LEDs: Difference between revisions
No edit summary |
m (LorurnA moved page Draft:RUT360 LEDs to RUT360 LEDs without leaving a redirect) |
||
| (7 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
{{Template: | {{Template: Networking_rutos_manual_leds | ||
<!------------------------DEVICE-----------------------> | <!------------------------DEVICE-----------------------> | ||
| name | | name = RUT360 | ||
| series | | series = RUT36X | ||
<!----------------------SEPARATORS---------------------> | <!----------------------SEPARATORS---------------------> | ||
| | | 2g = 0 <!-- 1 has 2G; 0 doesn't have 2G --> | ||
| eth = 1 <!-- 1 has ETH; 0 doesn't have ETH --> | |||
| eth_leds = 1 <!-- 1 for green; 2 for green & orange --> | |||
| mobile = 1 <!-- 1 has mobile; 0 doesn't have mobile --> | |||
| mobile_leds = 3 <!-- number of mobile signal strength type LEDs --> | |||
| power_leds = 1 <!-- number of power LEDs --> | |||
<!-------------------- | | wan = 0 <!-- 1 has WAN type LEDs; 0 doesn't have WAN type LEDs --> | ||
| wifi = 0 <!-- 1 has WiFi band LEDs; 0 doesn't have WiFi band LEDs --> | |||
}} | }} | ||
Latest revision as of 14:42, 21 January 2021
Main Page > EOL Products > RUT360 > RUT360 Manual > RUT360 LEDsThis page contains information the different types of LEDs and their behaviour on a RUT360 device.
Power LED
The power LED is located on the bottom left corner of the front panel, just under the power connector.
It indicates whether the device is powered on or not.
| State | Description |
|---|---|
| LED turned on | Device is powered on. |
| LED turned off | Device is not powered on. |
Ethernet port LEDs
The Ethernet port LEDs are located on the device's front panel, under each respective Ethernet port.
| State | Description |
|---|---|
| LED on | Operating as a 10/100 Mbps connection. |
| LED off | No link established. |
| LED blinking | Connection established and there is activity on this port (data being transferred). |
Mobile network type LEDs
The mobile network type LEDs are located near the SIM card slot.
They display which type of Internet connection is currently active.
| Action | Description |
|---|---|
| 3G LED turned on | Device is connected to a 3G network. |
| 4G LED turned on | Device is connected to a 4G network. |
| 3G blinking | Device is connected to a 3G network but hasn't received an IP address. |
| 3G blinking rapidly | Device is connected to a 3G network and data is being transferred. |
| 4G blinking | Device is connected to a 4G network but hasn't received an IP address. |
| 4G blinking rapidly | Device is connected to a 4G network and data is being transferred. |
| All LEDs blinking at the same time every 500 ms | No SIM card or incorrect PIN. |
| All LEDs turn on and off in a sequence one after the other | The device is attempting to connect to a mobile network operator. |
Mobile signal strength indication LEDs
The mobile signal strength indication LEDs are located near the SIM card slot.
The number of lit up LEDs represents a different mobile signal strength (RSSI) value in dBm.
| No. of lit up LEDs | Signal strength value |
|---|---|
| 0 | ≤ -111 dBm |
| 1 | -110 dBm to -82 dBm |
| 2 | -81 dBm to -52 dBm |
| 3 | ≥ -51 dBm |
The Mobile signal strength LEDs can also be used as a time indicator for holding the reset button. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a User's default configuration reset and 12 seconds (by default) to initiate a Factory reset. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a Factory reset. If the button was held down longer than 20 seconds (by default) no action will be taken.
While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with RUT360, when all 3 Mobile signal strength LEDs are lit up, they represent that 6 (LED number multiplied by 2) seconds have passed since you pressed down on the reset button.
After releasing the button at one of the reset periods, all 3 LEDs will start blinking every 1 second. This signifies that the router has begun the reset.