Template:Setting up mobile interface on rpi: Difference between revisions

From Teltonika Networks Wiki
No edit summary
 
(6 intermediate revisions by 2 users not shown)
Line 17: Line 17:
  ls /dev/ttyUSB*
  ls /dev/ttyUSB*


After executing the command yuo should see these devices:
After executing the command you should see these devices:


[[File:Networking_trm240_example_rpi_usb_dev_list_v1.png|border|class=tlt-border|650px|Image: 650 pixels]]
[[File:Networking_trm240_example_rpi_usb_dev_list_v1.png|border|class=tlt-border|650px|Image: 650 pixels]]
Line 119: Line 119:
[[File:Networking_trm240_example_rpi_get_interface_ip.png|border|class=tlt-border|650px|Image: 650 pixels]]
[[File:Networking_trm240_example_rpi_get_interface_ip.png|border|class=tlt-border|650px|Image: 650 pixels]]


If you want to check if your IP address changed you can visit this site [https://whatismyipaddress.com/ here].
[[Category:{{{name}}} Configuration Examples]]
 
==Introduction==
 
This article provides a guide on how to set up a mobile interface on a Raspberry PI single board computer using TRM240 device
 
{{Template:Setting up mobile interface on rpi}}
 
[[Category:TRM240]]

Latest revision as of 17:05, 18 January 2022

Prerequisites

You will need:

  • RPI3 B+ model
  • Raspbian 10 operating system
  • Internet connection

Step 1: preparing TRM240 for use

Before connecting the TRM240 to the RPI3, we need to prepare the device by inserting the SIM card in place. How to insert the SIM card you can find here. After inserting the card, don’t forget to mount the antenna for better GSM signal.

Step 2: connecting to RPI3

When the TRM240 device is ready, we need to connect it to one of the USB ports on the RPI3. After connecting it, wait about 15 seconds for device to boot up. After boot up you should see four new USB ports in the /dev directory. You can check them by executing this command in the terminal:

ls /dev/ttyUSB*

After executing the command you should see these devices:

Image: 650 pixels

We will be using ttyUSB3 port because this port is used for data flow.

Note: If you have connected more USB devices, the USB ports may differ.

Step 3: download necessary software

To start using the TRM240 device, first of all we need to install Debian’s Point-to-Point Protocol package. In the terminal execute these commands:

sudo apt update
sudo apt install -y ppp

This package will be used to establish a dial-up connection which will give us a new network interface called ppp0.

Step 4: create necessary scripts

Now we need to create three scripts which will allow us to create the internet connection. In the command line first of all execute these commands:

sudo mkdir -p /etc/chatscripts
sudo mkdir -p /etc/ppp/peers

When the necessary directories are created, inside the /etc/chatscripts directory create file by the name quectel-chat-connect and paste in these lines:

ABORT "BUSY"
ABORT "NO CARRIER"
ABORT "NO DIALTONE"
ABORT "ERROR"
ABORT "NO ANSWER"
TIMEOUT 30
"" AT
OK ATE0
OK ATI;+CSUB;+CSQ;+COPS?;+CGREG?;&D2
OK AT+CGDCONT=1,\"IP\",\"\\T\",,0,0
OK ATD*99#
CONNECT

Lets create another script in the same directory by the name quectel-chat-disconnect and paste in these lines:

ABORT "ERROR"
ABORT "NO DIALTONE"
SAY "\nSending break to the modem\n"
""  +++
""  +++
""  +++
SAY "\nGoodbay\n"

One more script is required inside directory /etc/ppp/peers. The script should be called gprs. Paste in these lines:

/dev/<usb_port> 115200
connect 'chat -s -v -f /etc/chatscripts/quectel-chat-connect -T <operator_apn>'
disconnect 'chat -s -v -f /etc/chatscripts/quectel-chat-disconnect'
hide-password
noauth
debug
defaultroute
noipdefault
novj
novjccomp
noccp
ipcp-accept-local
ipcp-accept-remote
local
lock
modem
dump
nodetach
nocrtscts
remotename 3gppp
ipparam 3gppp
ipcp-max-failure 30
usepeerdns

Before using this script, you need to change the lines <usb_port> and <operator_apn>. Usb port must be set to ttyUSB3 and apn to your operator’s provided apn.

Step 5: dial-up procedure

This is the last step. Now we need to dial-up the connection. In the terminal execute this command:

sudo pppd call gprs&

When you execute this command you will see a lot of debug output. Wait until you see the line “script /etc/ppp/ip-up finished”.

Image: 650 pixels

If you see this line you can check if the connection was created by executing this command in the terminal:

ifconfig ppp0

Image: 650 pixels

If you want to use the created connection as the default gateway, you need to add rule to the routing table. Execute this command in the terminal:

sudo route add default gw <your_ip_address> ppp0

You can lookup your IP address by executing this command in the terminal:

ifconfig ppp0

Image: 650 pixels

[[Category:{{{name}}} Configuration Examples]]