Difference between revisions of "Domnev"

From Teltonika Networks Wiki
 
(317 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
<p style="color:red">The information on this page is updated in accordance with the [https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads'''00.07.08'''] firmware version .</p>
 +
__TOC__
 
==Summary==
 
==Summary==
 +
This article contains instructions on how to send M-Bus data to the server using various protocols.
  
−
This chapter is a guide on configuring cobot.me provider '''hotspot''' instance on RUTX routers.
+
==Configuration overview & prerequisites==
 +
Before we begin, let's take a look at the configuration that we are attempting to achieve and the prerequisites that make it possible.
  
 +
'''Prerequisites''':
 +
* TRB143;
 +
* M-Bus device;
 +
* Server;
 +
* An end device (PC, Laptop, Tablet, Smartphone) for configuration;
  
−
If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should '''turn on "Advanced WebUI" mode'''. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.
 
  
−
[[File:Networking_{{{series}}}_manual_webui_basic_advanced_mode.gif|border|class=tlt-border]]
+
{{Template:Networking_rutos_manual_basic_advanced_webui_disclaimer
 +
| series = RUTX
 +
}}
  
−
==Step 1: cobot.me configuration ==
+
 
−
===Login===
+
==Adding M-Bus devices==
 +
To add a new device to the configuration press [[File:Add Button.png|60x90px]] button which is shown below.
 +
 
 +
[[File:Mbus adding new device.png||border|class=tlt-border]]
 +
 
 +
===Device configuration===
 +
----
 +
You will be granted to a new window. Configure your M-Bus device accordingly:
 +
 
 +
# '''Name''': Enter the desired name of the M-Bus device
 +
# '''Address type''': select which M-Bus address will be used
 +
# '''Primary/Secondary address''': specify M-Bus address
 +
 
 +
[[File:Mbus adding new device configuration v3.png|border|class=tlt-border]]
 +
 
 +
Test if the M-Bus device is reachable by a specified primary/secondary address. To do so click on [[File:Ping_device_option_mbus.png|110x110px]]. You might get on of two outputs:
 +
 
 +
* If you have specified correct primary/secondary address, you will receive:
 +
[[File:Mbus device pingable v2.png|border|class=tlt-border|300px]]
 +
 
 +
* If you have specified incorrect primary/secondary address, you will receive (if you do not know what address should be used, refer to the Scanning for available M-Bus devices (PRIDET URL) secion:
 +
[[File:Mbus device not pingable v2.png|border|class=tlt-border|300px]]
 +
 
 +
Once finished, save the configuration by clicking [[File:Savenapply button.png|Savenapply button.png]].
 +
 
 +
===Scanning for available M-Bus devices===
 +
----
 +
 
 +
If you are not sure what address your M-Bus devices have, you can try scanning for the available M-Bus devices. To do so click on [[File:Scan button.png]] button.
 +
 
 +
====Scan settings====
 +
----
 +
You will be granted to a new window. Configure scan settings accordingly:
 +
 
 +
# '''Scan type''': select which M-Bus address will be scanned
 +
# '''Scan range''': From what M-Bus address scanning will start and M-Bus address until scanning will be performed.
 +
[[File:Mbus scan.png|border|class=tlt-border]]
 +
 
 +
To start the scan click on [[File:Start scan button.png]] button.
 +
 
 +
====Found devices====
 
----
 
----
−
First, go to '''cobot.me''' and log into your account ('''LOG IN''' in the top right corner). If you don't have a registered account then you need to create one - click '''Start Your Free Trial'''.
+
Once the scan is finished you should see the list of M-Bus devices that TRB143 were able to find:
−
[[File:Cobotlogin.png|border|center]]
 
  
−
====Sign Up====
+
[[File:Mbus scanned devices add.png|border|class=tlt-border]]
  
−
After clicking '''Start Your Free Trial''' you will be redirected to register page. Enter you account information and click '''Next'''.
+
You can either [[File:Pencil2.png]] '''(1)''' M-Bus devices primary address or [[File:Add Button.png|60x90px]] '''(2)''' to the M-Bus devices list.
−
[[File:Signupfree.png|border|center]]
 
−
Next step is to enter further information of your account. After entering it click '''Add Space'''.
 
−
[[File:Register2Cobot.png|alt=|border|center]]
 
  
 +
==Gathering M-Bus data==
  
 +
If the device successfully added to the list, under the General settings you should see that the Status changes to <span style="color:green">Active</span>.
  
−
===Set Up new radius server===
+
[[File:Mbus status active v2.png|border|class=tlt-border]]
 +
 
 +
===Data collecting groups===
 
----
 
----
−
In the opened window click '''SETUP''' icon, then - '''Wifi Integration'''. You will be prompted to '''Radius Wifi Integration''' window. Click the '''Set up Radius Server.'''
+
To reach data collecting groups configuration press [[File:Pencil2.png]] button. [[File:Add Button.png|60x90px]] button lets you to create a new instance.
−
[[File:Imagea.png|border|center]]
 
  
−
===Network details===
+
[[File:Mbus data collect overview.png|border|class=tlt-border]]
  
−
You will be given your Radius server configuration data that you will need in the next step.
+
====Data collecting group instance====
−
[[File:Imageg.png|border|center]]
+
----
  
−
===Add Wifi Guest Accounts===
+
Each data collection group contains the following information. Configure device accordingly:
  
−
Click '''Wifi Guest Accounts''' in the bottom of the page to add accounts to let users access your wifi.
+
# '''Enabled''': on
−
[[File:Imagef.png|border|center]]
+
# '''Name''': desired name of the instance
 +
# '''Period''': desired time duration between data retrievals
 +
# '''Data type''': desired data type to process the received data. Depending on your needs you can select between 5 different data types: '''JSON, XML, ASCII, Hexadecimal''' and '''Binary'''.
  
−
Type user account information and click '''Add Account'''.
+
[[File:Mbus data collect group v2.png|border|class=tlt-border]]
−
[[File:Addusers.png|border|center]]
 
  
−
At the bottom of the page you can see all your created users.
+
You can check if your configuration works accordingly by pressing the [[File:Mbus test button.png]] button. You should see the data in a pop-up field:
−
[[File:Accounts.png|border|center]]
 
  
−
==Step 2: Router configuration ==
+
[[File:Mbus TEST output.png|border|class=tlt-border]]
  
−
===Log in===
+
====Group values====
 +
----
 +
To reach group values configuration press [[File:Pencil2.png]] button:
  
−
Open your RUTX homepage. That can be done by entering 192.168.1.1 in your internet browser's URL bar and log in with your credentials - the default credentials are '''admin''' as Username and '''admin01''' as Password (the address can different - depending if you changed it or not).
+
[[File:Mbus edit group values.png|border|class=tlt-border]]
  
−
===Creating wireless access point===
+
There you can adjust additional settings:
  
−
If you have already set up your wireless access point - skip this step.
+
# '''Enable''': Enable/disable data group value.
 +
# '''FCB toggle''': FCB (Frame Count-Bit), one-bit counter for reliable server-client communication.
 +
# '''Manufacturer information''': Select to include manufacturer information in the payload.
 +
# '''Selected parameters''': Select to include the all parameters saved from device, or a custom subset of them. If the custom is selected you can specify '''frame''', '''record''' numbers and also a '''paramater'''
  
−
Open the wireless configuration panel by clicking '''Network → Wireless.''' To begin configuring WiFi AP first click the ''''ADD'''<nowiki/>' button.
+
[[File:Mbus device groupsa.png|border|class=tlt-border]]
−
[[File:NewAP.png|border|center]]
 
  
−
Check the '''Enable wireless''' checkbox, enter router's '''SSID''' and for the safety purpose click '''Wireless Security'''.
 
−
[[File:Apconfig1.png|border|center]]
 
  
−
Choose your '''Encryption''', enter the '''Key''' and click '''Save'''.
+
==Sending data to the server==
−
[[File:Apconfig2.png|border|center]]
+
This section contains information on how to send M-Bus data to the server using MQTT and HTTP protocols.
  
−
===Set up hotspot===
+
===Data to Server configuration===
 +
----
 +
To set up Data to Server, navigate to Services → Data to Server. Enter desired name of the instnace and hit [[File:Add Button.png|60x90px]] button which is shown below.
  
−
Open the hotspot configuration panel by clicking '''Services → Hotspot'''
+
[[File:Mbus data to server create.png|border|class=tlt-border]]
−
[[File:Hotspotconfig1.png|border|center]]
 
  
 +
===Data configuration===
 +
----
  
−
'''Hotspot configuration'''
+
[[File:Mbus data to server configuration.png|border|class=tlt-border]]
−
[[File:Hotspotconfig2.png|border|center]]
 
  
−
Use configuration details from '''Step 1'''.
 
  
−
Check '''enable''' box
+
Once finished configuring Data configuration tab click on [[File:Mbus data to server collection edit.png|160x160px]] button.
  
−
Select '''External radius''' from '''Authentication mode''' dropbox
+
===Collection configuration===
 +
----
  
−
Select '''PAP''' from '''Authentication protocol''' dropbox
+
[[File:Mbus data to server collection configuration.png|border|class=tlt-border]]
  
−
Type configuration details '''RADIUS Server''', '''Authentication port''', '''Accounting port''' and '''Radius secret key'''
+
Once finished configuring Collection configuration tab click on [[File:Mbus data to server server button.png|160x160px]] button.
  
−
And click '''Save'''
+
===Server configuration===
−
[[File:Hotspotconfigq.png|border|center]]
+
----
  
−
==Test your Hotspot==
+
====HTTP configuration====
 +
----
  
−
Try connecting to your router using computer or mobile phone.
+
[[File:Mbus data to server HTTP configuration.png|border|class=tlt-border]]
  
−
Select your router.
+
====MQTT configuration====
−
[[File:Wifimobile.png|border|center]]
+
----
  
−
After successful connection visit any website. You should be redirected to hotspot login page.
+
[[File:Mbus data to server MQTT configuration.png|border|class=tlt-border]]
  
−
Type your username and password.
+
Once finished configuring Server configuration tab click on [[File:Savenapply button.png|Savenapply button.png]] button.
  
−
Click '''Login'''
 
−
[[File:Wifilogin.png|border|center]]
 
  
−
You should see a message '''Authorization Successful'''
+
==See Also==
−
[[File:Wifisuccess.png|border|center]]
 
  
 
==External links==
 
==External links==
−
http://www.cobot.me
+
[https://flespi.io/#/ Flespi.io]
−
 
 
−
[[Category:IoT]]
 

Latest revision as of 09:32, 22 August 2024

The information on this page is updated in accordance with the 00.07.08 firmware version .

Summary

This article contains instructions on how to send M-Bus data to the server using various protocols.

Configuration overview & prerequisites

Before we begin, let's take a look at the configuration that we are attempting to achieve and the prerequisites that make it possible.

Prerequisites:

  • TRB143;
  • M-Bus device;
  • Server;
  • An end device (PC, Laptop, Tablet, Smartphone) for configuration;


If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Advanced" button, located at the top of the WebUI.

Networking rutos manual webui basic advanced mode 75.gif


Adding M-Bus devices

To add a new device to the configuration press Add Button.png button which is shown below.

Mbus adding new device.png

Device configuration

You will be granted to a new window. Configure your M-Bus device accordingly:

  1. Name: Enter the desired name of the M-Bus device
  2. Address type: select which M-Bus address will be used
  3. Primary/Secondary address: specify M-Bus address

Mbus adding new device configuration v3.png

Test if the M-Bus device is reachable by a specified primary/secondary address. To do so click on Ping device option mbus.png. You might get on of two outputs:

  • If you have specified correct primary/secondary address, you will receive:

Mbus device pingable v2.png

  • If you have specified incorrect primary/secondary address, you will receive (if you do not know what address should be used, refer to the Scanning for available M-Bus devices (PRIDET URL) secion:

Mbus device not pingable v2.png

Once finished, save the configuration by clicking Savenapply button.png.

Scanning for available M-Bus devices

If you are not sure what address your M-Bus devices have, you can try scanning for the available M-Bus devices. To do so click on Scan button.png button.

Scan settings

You will be granted to a new window. Configure scan settings accordingly:

  1. Scan type: select which M-Bus address will be scanned
  2. Scan range: From what M-Bus address scanning will start and M-Bus address until scanning will be performed.

Mbus scan.png

To start the scan click on Start scan button.png button.

Found devices

Once the scan is finished you should see the list of M-Bus devices that TRB143 were able to find:

Mbus scanned devices add.png

You can either Pencil2.png (1) M-Bus devices primary address or Add Button.png (2) to the M-Bus devices list.

Gathering M-Bus data

If the device successfully added to the list, under the General settings you should see that the Status changes to Active.

Mbus status active v2.png

Data collecting groups

To reach data collecting groups configuration press Pencil2.png button. Add Button.png button lets you to create a new instance.

Mbus data collect overview.png

Data collecting group instance

Each data collection group contains the following information. Configure device accordingly:

  1. Enabled: on
  2. Name: desired name of the instance
  3. Period: desired time duration between data retrievals
  4. Data type: desired data type to process the received data. Depending on your needs you can select between 5 different data types: JSON, XML, ASCII, Hexadecimal and Binary.

Mbus data collect group v2.png

You can check if your configuration works accordingly by pressing the Mbus test button.png button. You should see the data in a pop-up field:

Mbus TEST output.png

Group values

To reach group values configuration press Pencil2.png button:

Mbus edit group values.png

There you can adjust additional settings:

  1. Enable: Enable/disable data group value.
  2. FCB toggle: FCB (Frame Count-Bit), one-bit counter for reliable server-client communication.
  3. Manufacturer information: Select to include manufacturer information in the payload.
  4. Selected parameters: Select to include the all parameters saved from device, or a custom subset of them. If the custom is selected you can specify frame, record numbers and also a paramater

Mbus device groupsa.png


Sending data to the server

This section contains information on how to send M-Bus data to the server using MQTT and HTTP protocols.

Data to Server configuration

To set up Data to Server, navigate to Services → Data to Server. Enter desired name of the instnace and hit Add Button.png button which is shown below.

Mbus data to server create.png

Data configuration

Mbus data to server configuration.png


Once finished configuring Data configuration tab click on Mbus data to server collection edit.png button.

Collection configuration

Mbus data to server collection configuration.png

Once finished configuring Collection configuration tab click on Mbus data to server server button.png button.

Server configuration

HTTP configuration

Mbus data to server HTTP configuration.png

MQTT configuration

Mbus data to server MQTT configuration.png

Once finished configuring Server configuration tab click on Savenapply button.png button.


See Also

External links

Flespi.io

Retrieved from "https://wiki.teltonika-networks.com/index.php?title=Domnev&oldid=131099"