Template:Networking rutos manual network: Difference between revisions
No edit summary |
No edit summary |
||
| Line 71: | Line 71: | ||
</ul> | </ul> | ||
</td> | </td> | ||
</tr> | |||
<tr> | |||
<td>Provider</td> | |||
<td>Network operator's name</td> | |||
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 96: | Line 100: | ||
</ul> | </ul> | ||
</td> | </td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 128: | Line 128: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Carrier Aggregation</td> | |||
<td>LTE Advanced Carrier Aggregation, CA, is one of the key techniques used to enable the very high data rates of 4G to be achieved. | <td>LTE Advanced Carrier Aggregation, CA, is one of the key techniques used to enable the very high data rates of 4G to be achieved. | ||
By combining more than one carrier together, either in the same or different bands it is possible to increase the bandwidth available and in this way increase the capacity of the link. | By combining more than one carrier together, either in the same or different bands it is possible to increase the bandwidth available and in this way increase the capacity of the link. | ||
| Line 140: | Line 136: | ||
<td>Connected band</td> | <td>Connected band</td> | ||
<td>Currently used mobile frequency band.</td> | <td>Currently used mobile frequency band.</td> | ||
</tr> | |||
<tr> | |||
<td>Signal strength</td> | |||
<td>Received signal strength indicator (<b>[[RSSI]]</b>) measured in dBm. Values closer to 0 indicate a better signal strength</td> | |||
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 182: | Line 182: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td> | <td>Cell ID</td> | ||
<td> | <td>The ID of the cell that the modem is currently connected to</td> | ||
</tr> | |||
<tr> | |||
<td>LAC</td> | |||
<td>The Location Area Code, abbreviated as LAC is the unique number given to each location area within the network. The served area of a cellular radio access network is usually divided into location areas, consisting of one or several radio cells.</td> | |||
</tr> | |||
<tr> | |||
<td>Physical cell ID</td> | |||
<td></td> | |||
</tr> | |||
<tr> | |||
<td>EARFCN</td> | |||
<td></td> | |||
</tr> | |||
<tr> | |||
<td>Mobile country code</td> | |||
<td></td> | |||
</tr> | </tr> | ||
<tr> | |||
<td>Mobile network code</td> | |||
<td></td> | |||
</tr> | |||
</table> | </table> | ||
{{#switch: {{{series}}} | RUTX | RUTM= | {{#switch: {{{series}}} | RUTX | RUTM= | ||
Revision as of 13:00, 5 September 2023
Template:Networking rutos manual fw disclosure
Summary
The Network page contains information related to the device's networking. This chapter is an overview of the Network page in {{{name}}} devices.
If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Advanced" button, located at the top of the WebUI.
LAN
This tab displays information about the device's local network(s). The figure below is an example of the Network window:
| lan information | |
|---|---|
| Name | LAN interface name |
| IP address | IP address of the LAN interface |
| Netmask | Netmask of the LAN interface. In a sense, a netmask specifies the size of a network. In other words, it indicates which part of the IP address denotes the network, and which denotes the device |
| dhcp leases | |
| Hostname | Hostname of a LAN client |
| IP Address | IP address of a LAN client |
| MAC Address | MAC address of a LAN client |
| Leasetime Remaining | Remaining lease time for a DHCP client. Active DHCP lease holders will try to renew their DHCP leases after a half of the lease time passes. |
[[Category:{{{name}}} Status section]]