TRB256 LEDs: Difference between revisions
(Created page with "{{Template: Networking_rutos_manual_leds <!------------------------DEVICE-----------------------> | name = TRB256 | series = TRB2M <!----------------------SEPARATO...") |
No edit summary |
||
| Line 4: | Line 4: | ||
| series = TRB2M | | series = TRB2M | ||
<!----------------------SEPARATORS---------------------> | <!----------------------SEPARATORS---------------------> | ||
| 2g = | | 2g = 1 <!-- 1 has 2G; 0 doesn't have 2G --> | ||
| 5g = | | 5g = 0 <!-- 1 has 5G; 0 doesn't have 5G --> | ||
| eth = 1 <!-- 1 has ETH; 0 doesn't have ETH --> | | eth = 1 <!-- 1 has ETH; 0 doesn't have ETH --> | ||
| eth_leds = 2 <!-- 1 for green; 2 for green & orange --> | | eth_leds = 2 <!-- 1 for green; 2 for green & orange --> | ||
| Line 11: | Line 11: | ||
| mobile_leds = 3 <!-- number of mobile signal strength type LEDs --> | | mobile_leds = 3 <!-- number of mobile signal strength type LEDs --> | ||
| power_leds = 1 <!-- number of power LEDs --> | | power_leds = 1 <!-- number of power LEDs --> | ||
| wan = | | wan = 0 <!-- 1 has WAN type LEDs; 0 doesn't have WAN type LEDs --> | ||
| wifi = | | wifi = 0 <!-- 1 has WiFi band LEDs; 0 doesn't have WiFi band LEDs --> | ||
}} | }} | ||
Revision as of 10:49, 5 January 2024
Main Page > TRB Gateways > TRB256 > TRB256 Manual > TRB256 LEDsThis page contains information the different types of LEDs and their behaviour on a TRB256 device.
Power LED
The power LED is located on the bottom left corner of the front panel, just under the power connector.
It indicates whether the device is powered on or not.
| State | Description |
|---|---|
| LED turned on | Device is powered on. |
| LED turned off | Device is not powered on. |
Ethernet port LEDs
There are two LEDs located at the top of each Ethernet port.
They provide information on the current states of the Ethernet ports. Each port has two LEDs:
- Orange - 10/100 Mbps connection
- Green- 1000 Mbps connection
Below is an explanation on the behaviours of green and orange LEDs.
| State | Description |
|---|---|
| LED on | A data connection on the port is operational (cable plugged in, end device visible, no data is being transferred). |
| LED off | No data connection on the port is operational (no cable, bad cable or end device not visible for some other reason (such as damaged network card). |
| LED blinking | Connection established and data is being transferred over this port. |
Mobile network type LEDs
The mobile network type LEDs are located on left side of the back panel:
They display which type of Internet connection is currently active.
| Action | Description |
|---|---|
| 2G, NB and M1 LEDs are blinking at the same time | No SIM or bad PIN |
| 2G, NB and M1 LEDs light up and down in sequence | Searching mobile network operator |
| 2G/NB/M1 LED blinking | Gateway connected to 2G/NB/M1, no data session established |
| 2G/NB/M1 LED turned ON | Gateway connected to 2G/NB/M1 with data session |
| 2G/NB/M1 LED blinking | Gateway connected to 2G/NB/M1 and data is being transferred |
Mobile signal strength indication LEDs
The mobile signal strength indication LEDs are located on right side of the back panel.
The number of lit up LEDs represents a different mobile signal strength (RSSI) value in dBm.
| No. of lit up LEDs | Signal strength value |
|---|---|
| 0 | ≤ -111 dBm |
| 1 | -110 dBm to -82 dBm |
| 2 | -81 dBm to -52 dBm |
| 3 | ≥ -51 dBm |
The Mobile signal strength LEDs can also be used as a time indicator for holding the reset button. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a User's default configuration reset and 12 seconds (by default) to initiate a Factory reset. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a Factory reset. If the button was held down longer than 20 seconds (by default) no action will be taken.
While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with TRB256, when all 3 Mobile signal strength LEDs are lit up, they represent that 6 (LED number multiplied by 2) seconds have passed since you pressed down on the reset button.
After releasing the button at one of the reset periods, all 3 LEDs will start blinking every 1 second. This signifies that the router has begun the reset.