Template:Networking rutos manual leds: Difference between revisions
No edit summary Tag: Reverted |
No edit summary Tag: Reverted |
||
| Line 116: | Line 116: | ||
{{#switch: {{{eth_leds}}} | {{#switch: {{{eth_leds}}} | ||
| 1 =The <b>Ethernet port LEDs</b> are located on the device's front panel, under each respective Ethernet port. | | 1 = The <b>Ethernet port LEDs</b> are located on the device's front panel, under each respective Ethernet port. | ||
[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]] | [[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]] | ||
| Line 142: | Line 142: | ||
</tr>--> | </tr>--> | ||
</table> | </table> | ||
| 2=There are two <b>LEDs</b> located at the top of each <b>Ethernet port</b>. | | 2 = There are two <b>LEDs</b> located at the top of each <b>Ethernet port</b>. | ||
[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]] | [[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|500px]] | ||
| Line 215: | Line 215: | ||
</tr> | </tr> | ||
</table> | </table> | ||
}}{{#ifeq: {{{mobile}}} | 1 | <h2>Mobile network type LEDs</h2> | |||
{{#switch: {{{name}}} | TRB256 = | {{#switch: {{{name}}} | TRB256 = | ||
The <b>mobile network type LEDs</b> are located on left side of the back panel: | The <b>mobile network type LEDs</b> are located on left side of the back panel: | ||
Revision as of 11:36, 13 November 2024
This page contains information the different types of LEDs and their behaviour on a {{{name}}} device.
Power LED
The power LED is located on the bottom left corner of the front panel, just under the power connector.
[[File:Networking_{{{name}}}_manual_leds_power_led.png|500px]]
It indicates whether the device is powered on or not.
| State | Description |
|---|---|
| M LED turned on | Device is powered over the Main power connector. |
| M LED turned off | Device is not powered over the Main power connector. |
| R LED turned on | Device is powered over the Reserve power connector. |
| R LED turned off | Device is not powered over the Reserve power connector. |
{{#ifeq: {{{eth}}} | 1 |
Ethernet port LEDs
{{#ifeq: {{{mobile}}} | 1 |
Mobile network type LEDs
The mobile network type LEDs are located near the SIM card slot.
[[File:Networking_{{{name}}}_manual_leds_mobile_network_type_leds.png|500px]]
They display which type of Internet connection is currently active.
| Action | Description |
|---|---|
| 3G LED turned on | Device is connected to a 3G network. |
| 4G LED turned on | Device is connected to a 4G network. |
| 3G blinking | Device is connected to a 3G network but hasn't received an IP address. |
| 3G blinking rapidly | Device is connected to a 3G network and data is being transferred. |
| 4G blinking | Device is connected to a 4G network but hasn't received an IP address. |
| 4G blinking rapidly | Device is connected to a 4G network and data is being transferred. |
| All LEDs blinking at the same time every 500 ms | No SIM card or incorrect PIN. |
| All LEDs turn on and off in a sequence one after the other | The device is attempting to connect to a mobile network operator. |
Mobile signal strength indication LEDs
The mobile signal strength indication LEDs are located near the SIM card slot.
[[File:Networking_{{{name}}}_manual_leds_mobile_signal_strength_leds.png|500px]]
The number of lit up LEDs represents a different mobile signal strength (RSSI) value in dBm.
| No. of lit up LEDS | Signal strength |
|---|---|
| 0 | ≤ -111 dBm |
| 1 | -110 dBm to -97 dBm |
| 2 | -96 dBm to -82 dBm |
| 3 | -81 dBm -67 dBm |
| 4 | -66 dBm to -52 dBm |
| 5 | ≥ -51 dBm |
The Mobile signal strength LEDs can also be used as a time indicator for holding the reset button. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a User's default configuration reset and 12 seconds (by default) to initiate a Factory reset. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a Factory reset. If the button was held down longer than 20 seconds (by default) no action will be taken.
While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with {{{name}}}, when all {{{mobile_leds}}} Mobile signal strength LEDs are lit up, they represent that Expression error: Unrecognized punctuation character "{". (LED number multiplied by 2) seconds have passed since you pressed down on the reset button.
After releasing the button at one of the reset periods, all {{{mobile_leds}}} LEDs will start blinking every 1 second. This signifies that the router has begun the reset.
[[Category:{{{name}}} Manual]]