RUT955 Administration

Summary

This chapter is an overview of RUT routers' System->Administration section

General

The General section is used to change some of the most general configurations of the router (password, language, etc.)

Field name	Value	Description
Router name	string; Default: RUT955	Router's name, used for easier management purposes
Host name	string; Default: Teltonika-RUT955.com	Router's host name, i.e., an address from which you can reach the router's WebUI
New password | Confirm new password	string; Default: admin01	Router's admin password
Language	English | Deutsch | Français | Turkish; Default: English	Selects the router's interface language
IPv6 Support	yes | no; Default: no	Toggles IPv6 suport ON or OFF
Show mobile info at login page	yes | no; Default: no	Show mobile data connection information (signal strength, state, service mode) at login page
Show WAN IP at login page	yes | no; Default: no	Show the router's WAN IP address at login page
LEDs Indication	yes | no; Default: yes	Toggles LED indication ON or OFF
Restore to default	-	Restores the router to it's default state (factory settings)

Troubleshoot

Field name	Value	Description
System log level	Debug | Info | Notice | Warning | Error | Critical | Alert | Emergency; Default: Debug	You can watch logs by choosing a group from the dropdown list and clicking Show button
Save log in	RAM memory | Flash memory; Default: RAM memory	Specifies where to save log information. The router needs to be rebooted in order for this effect to take place
Include GSMD information	yes | no; Default: yes	Inlcludes GSMD information in the router's logs
Include PPPD information	yes | no; Default: no	Inlcludes PPPD information in the router's logs
Include Chat script information	yes | no; Default: yes	Inlcludes Chat script information in the router's logs
Include network topology information	yes | no; Default: no	Inlcludes network topology information in the router's logs

System log - Provides on-screen System logging information. It does not, however, substitute troubleshooting file.

Kernel log - Provides on-screen Kernel logging information. It does not, however, substitute the troubleshooting file.

Troubleshoot file - Downloadable archive, that contains full router configuration and all System log files.

In addition, you can also download the router's troubleshoot file at any time and the TCP dump file if the Enable TCP dump field is checked.

Backup

The Backup page is used to set up configuration back up files.

Backup archive downloads the current router settings file to your personal computer. This file can be loaded to other RUT955 devices with the same Firmware version in order to quickly configure them.

Restore from backup - Select, upload and restore router settings file from your personal computer or from RMS.

Access Control

General

---

The Access Control General window is used the Enable or Disable SSH, HTTP or HTTPS remote or local access to the RUT device.

Safety

---

Field name	Value	Description
Enable	yes | no; Default: yes	Toggles secure SSH/WebUI access ON or OFF. If this is checked, devices logging in have a limited amount of tries specified in the Fail count field to log in to the router
Clean after reboot	yes | no; Default: no	If this field is checked, blocked addresses are removed after every reboot
Fail count	integer; Default: 5	Maximal login fail count after which the devices's address is blocked and appears in the List Of Blocked Addresses section

Diagnostics

The Diagnostics page is used to diagnose whether you have an internet connection, trace routes of specified addresses and to perform NSlookups by sending ICMP ping packets to a specified host or IP address.

MAC Clone

Overview

The Administration->Overview section is used to configure which widgets should be shown in the Overview page.

Monitoring

The Monitoring Section is used to configure how the router will be connecting to the Remote Management System (RMS). Adding a device to RMS takes place from the RMS side, all you need to do from the router's side is to enable Remote Monitoring. You will need to know the router's MAC Address and Serial Number to connect it to RMS, both of which are provided in this window.