Template:Networking rutos manual devices: Difference between revisions
No edit summary |
No edit summary |
||
| Line 11: | Line 11: | ||
<b>Virtual Extensible LAN</b> is a tunneling interface protocol (VXLAN), which allows VXLAN layer 2 virtualization over layer 3 network. VXLAN establishes a logical tunnel between the source and destination network devices, through which it uses MAC-in-UDP encapsulation for packets. In addition, it helps customer sites to configure layer2 VPN. | <b>Virtual Extensible LAN</b> is a tunneling interface protocol (VXLAN), which allows VXLAN layer 2 virtualization over layer 3 network. VXLAN establishes a logical tunnel between the source and destination network devices, through which it uses MAC-in-UDP encapsulation for packets. In addition, it helps customer sites to configure layer2 VPN. | ||
<b>Note:</b> VXLAN is additional software that can be installed from the <b>System → [[{{{name}}} Package Manager|Package Manager]]</b> page. | <b>Note:</b> VXLAN is additional software on some devices that can be installed from the <b>System → [[{{{name}}} Package Manager|Package Manager]]</b> page. | ||
===Device configuration (VXLAN)=== | ===Device configuration (VXLAN)=== | ||
Latest revision as of 14:50, 20 February 2025
The information in this page is updated in accordance with firmware version .
VXLAN
Virtual Extensible LAN is a tunneling interface protocol (VXLAN), which allows VXLAN layer 2 virtualization over layer 3 network. VXLAN establishes a logical tunnel between the source and destination network devices, through which it uses MAC-in-UDP encapsulation for packets. In addition, it helps customer sites to configure layer2 VPN.
Note: VXLAN is additional software on some devices that can be installed from the System → [[{{{name}}} Package Manager|Package Manager]] page.
Device configuration (VXLAN)
The Device configuration section is used to set up VXLAN devices.
To add a new device - select 'VXLAN' and click 'Add' button:
After clicking 'Add' you will be redirected to the newly added VXLAN device configuration page.
Configuration (VXLAN)
| Field | Value | Description |
|---|---|---|
| Name | string; default: vxlan1 | Name of the device. |
| MAC address | mac; default: empty | Override MAC address of the device. If not set, the device's MAC address will be used. |
| MTU | integer [98..9000]; default: empty | Sets the maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction. |
| VNI | integer [1..16777215]; default: 1 | VXLAN network identifier. |
| PORT | integer [1..65535]; default: 4789 | VXLAN network identifier. |
| Local address | ip; default: none | Sets the local source IP address for VXLAN tunneling. |
| Remote address | ip; default: none | Specifies the multicast group or remote IP address used for VXLAN tunneling. |
| Ageing | integer [1..4294967295]; default: empty | Specifies the lifetime in seconds of FDB entries learnt by the kernel. |
| Max FDB entries | integer [1..4294967295]; default: empty | Specifies the maximum number of FDB entries. |
| IPv4 checksum | off | on; default: off | Specifies if UDP checksum is calculated for transmitted packets over IPv4. |
| Learning | off | on; default: off | Enables or disables MAC learning for VXLAN. |
| Proxy | off | on; default: off | Enables or disables ARP proxy for VXLAN. |
| RSC | off | on; default: off | Specifies if route short circuit is turned on. |
| L2miss | off | on; default: off | Specifies if netlink LLADDR miss notifications are generated. |
| L3miss | off | on; default: off | Specifies if netlink IP ADDR miss notifications are generated. |
| IPv6 TX checksum | off | on; default: off | Enables or disables UDP checksum calculation for transmitted packets over IPv6. |
| IPv6 RX checksum | off | on; default: off | Allow incoming UDP packets over IPv6 with zero checksum field. |
[[Category:{{{name}}} Network section]]