Template:Networking trb manual powering options: Difference between revisions

From Teltonika Networks Wiki
VisualWikitext
No edit summary
No edit summary
Line 5: Line 5:
| series = {{{series}}}
| series = {{{series}}}
}}
}}
{{#ifeq: {{{eth}}} | 1 | {{Template: networking_device_manual_powering_options_passive_poe
| series    = {{{series}}}
| file_lan1 = {{{file_lan1}}}
| size_lan1 = {{{size_lan1}}}}}
|}}
{{#ifeq: {{{eth}}} | 1 | {{Template: networking_device_manual_powering_options_simultaneous_powering}}|}}
{{#ifeq: {{{rs485}}} | 1 |
You can also power the device over the RS485 connector. In order to do so, adhere to the steps below.


{{#ifeq:{{{name}}} | TRB140
<ul>
  | {{Template: networking_device_manual_powering_options_passive_poe
    <li>Unscrew the two hex bolts and remove the back panel.<br>[[File:Networking_trb145_manual_powering_options_rs485_unscrew_hex_bolts.png|300px]]</li>
      | series    = {{{series}}}
    <li>Remove the PCB board from the case.</li>
      | file_lan1 = {{{file_lan1}}}
    <li>Place a resistor between the "RS PWR ENABLE" pins (marked 1 & 2 in the figure below) on the PCB board:<br>[[File:Networking_trb145_manual_powering_options_rs485.png|400px]]</li>
      | size_lan1 = {{{size_lan1}}}
     <li>Connect pins 3 (GND) and 6 (PWR) to a 9-30 VDC power supply.<br>[[File:Networking_trb145_manual_powering_options_rs485_connector_pinout.png]]</li>
     }}
    <li>If the PWR LED lights up, the device was successfully powered over the RS485 connector.</li>
}}
</ul>
 
|}}
{{#ifeq:{{{name}}} | TRB140
  | {{Template: networking_device_manual_powering_options_simultaneous_powering}}
}}
 
[[Category:{{{name}}} Manual]]
[[Category:{{{name}}} Manual]]

Revision as of 07:51, 2 September 2020

This chapter contains information on powering options supported by {{{name}}} devices.

Power socket

The device has a 4 pin power socket and can be powered by a 9-30 VDC power supply unit (PSU). Refer to the image below for the power socket's pinout information:

{{Template: Networking_{{{series}}}_manual_power_socket_pinout 

   |file_power_socket={{{file_power_socket}}}
 }}

If you decide not to use the standard 9 VDC wall adapter and want to power the device from a higher voltage (15-30 VDC), please make sure that you choose a power supply of high quality. Some power supplies can produce voltage peaks significantly higher than the declared output voltage, especially during connection and disconnection.

While the device is designed to accept input voltage of up to 30 VDC peaks, high voltage power supplies can harm the device. If you want to use high voltage power supplies it is recommended to also use additional safety equipment to suppress voltage peaks from the power supply.

Suggestion: If you're using a different power supply than the one included in the standard packaging, make sure it meets the same power (W) specifications as the original. Otherwise, some features of the device might not work properly. Please refer to the device's portfolio page to verify the power supply specifications: [[{{{name}}}_Power_Consumption|Power Consumption]]



[[Category:{{{name}}} Manual]]

Retrieved from "https://wiki.teltonika-networks.com/index.php?title=Template:Networking_trb_manual_powering_options&oldid=71266"