Template:Networking rutos manual failover: Difference between revisions
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
{{Template:Networking_rutos_manual_fw_disclosure | {{Template:Networking_rutos_manual_fw_disclosure | ||
| fw_version = {{{series}}}_R_00.02.03.1 | | fw_version = {{{series}}}_R_00.02.03.1 | ||
| series = {{{series}}} | | series = {{{series}}} | ||
}} | }} | ||
__TOC__ | |||
==Summary== | ==Summary== | ||
This chapter is an overview of the Failover and Load Balancing functions in {{{name}}} routers. | This chapter is an overview of the Failover and Load Balancing functions in {{{name}}} routers. | ||
{{Template:Networking_rutos_manual_basic_advanced_webui_disclaimer}} | |||
{{Template:Networking_rutos_manual_basic_advanced_webui_disclaimer | |||
| series = {{{series}}} | |||
}} | |||
===Failover=== | ===Failover=== | ||
---- | ---- | ||
Revision as of 10:54, 19 May 2020
Template:Networking rutos manual fw disclosure
Summary
This chapter is an overview of the Failover and Load Balancing functions in {{{name}}} routers.
If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Advanced" button, located at the top of the WebUI.
Failover
This function allows you to back up your primary connection in case it goes down. For example, when primary connection goes down, router will try to use second configured backup interface. If second interface will also become unavailable, router will try to use third backup interface.
In order to set priorities, simply press left mouse click on the interface, then drag it to the 1st, 2nd or other position and then press Save & Apply.
Below is an example of Failover settings section.
File:Networking rutx11 manual failover confing v1.png
By pressing Edit button, you can find more Failover interface settings. More information and example are presented below.
| field name | value | description |
|---|---|---|
| Enable | off | on; Default: off | Toggles the interface ON or OFF |
| Interval | Default: 3 | Number of seconds between each test |
| Method | Default: Ping | Method, how internet connection will be tested |
| Track IP | IP;Default: 8.8.4.4; 8.8.8.8 | The hosts to test if interface is still alive. If this value is missing the interface is always considered up |
| Reliability | Default: 1 | Number of hosts that must reply for the test to be considered as successful. Ensure there are at least this many hosts defined or the interface will always be considered down |
| Count | Default: 1 | Number of pings to send to each host with each test |
| Up | Default: 3 | Number of successful tests to considered link as alive |
| Down | Default: 3 | Number of failed tests to considered link as dead |
Load Balancing
Load balancing lets users create rules that divide traffic between different interfaces. Below is an example of Load Balancing settings window.
As you may notice from the image above, the configuration is very simple. You can assign ratio values to WAN interfaces. The ratio values represent a percentage of load that will go through an interface. For example, if you set that 3 parts of traffic would go through the interface and 2 parts would go through the Wired interface, it would mean that roughly 60% (3/5) of data will be transferred through , 40% (2/5) through Wired. If the ratios would be different, say : 5, Wired: 10, then 33% (5/15) of data would be transferred through , and 66% (10/15) would go through Wired.
If you press Edit button, you will be transferred to the same interface settings that were described in Failover section.
[[Category:{{{name}}} Network section]]