Template:Networking rutos manual storage memory expansion: Difference between revisions

From Teltonika Networks Wiki
(Created page with "{{Template:Networking_rutos_manual_fw_disclosure | fw_version = {{{series}}}_R_00.02.04.1 | series = {{{series}}} }} ==Summary== The <b>Storage Memory Expansion</b> func...")
 
No edit summary
Line 1: Line 1:
{{Template:Networking_rutos_manual_fw_disclosure
{{Template:Networking_rutos_manual_fw_disclosure
| fw_version = {{{series}}}_R_00.02.04.1
| fw_version = {{{series}}}_R_00.02.05
| series    = {{{series}}}
| series    = {{{series}}}
}}
}}

Revision as of 13:26, 20 July 2020

Template:Networking rutos manual fw disclosure

Summary

The Storage Memory Expansion function provides the possibility to expand the device's flash memory with a USB mass storage device.

This manual page provides an overview of the Storage Memory Expansion window in {{{name}}} devices.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Advanced" button, located at the top of the WebUI.

Memory Expansion

You can expand the flash memory of this device with a USB Mass Storage Device (MSD) and use the extra memory to install additional software packages. This section provides instruction on how to do just that. However, there are a few prerequisites and warnings to take note of before using memory expansion.

To be eligible for memory expansion, the USB MSD must meet the following restrictions.

  • The MSD must be the last one (chronologically) inserted.
  • If you are using a USB hub, the target MSD must be the last one attached to the hub.
  • No important data on the MSD as it will be wiped during expansion setup!

When expansion is enabled, do not detach the USB device as this will delete the data stored on it. Changes made to the device configuration while expansion was enabled will disappear after it is disabled.

Enabling memory expansion


To successfully expand the flash memory of your device follow the steps described below.

  1. Attach a USB Mass Storage Device (MSD) to the USB connector on the device and go to the Services → Storage Memory Expansion page.
  2. Set the 'Enable storage expansion' slider to 'on' and click 'Save & Apply'.
  3. You will see a pop-up asking for confirmation. Take note that if you continue from this point on:
    • your USB device's memory will be wiped and formatted to ext2 format;
    • your device's current configuration will be backed up and restored to this point if the USB drive is removed or memory expansion is disabled;
    • the entire procedure will take up to 5 minutes including a reboot.
    Click 'Continue' to proceed.
  4. If all is in order you should see a 'Formatting MSD...' message on the screen. This indicates that the MSD is being formatted and integrated with the system. This procedure can take 3 to 4 minutes and is followed by a reboot of the device.
  5. Your device's flash memory will be expanded once the reboot has finished. In order to check, log in to the WebUI and look to the 'System' widget in the 'Overview' page. Hover your mouse cursor over the 'FLASH' memory indicator; you should see an increase to the device's flash memory.

Disabling memory expansion


To successfully disable memory expansion follow the steps described below.

  1. Go to the Services → Storage Memory Expansion page.
  2. Set the 'Enable storage expansion' slider to 'off' and click 'Save & Apply'.
  3. You will see a pop-up asking for confirmation. Take note that if you continue from this point on:
    • your USB device's memory will be wiped and formatted to NTFS format;
    • your device's configuration will be restored to the point it was before memory expansion;
    • the entire procedure will take up to 2 minutes including a reboot.
    Click 'Continue' to proceed.
  4. If all is in order you should see a 'Formatting MSD...' message on the screen. This indicates that the MSD is being formatted and integrated with the system. This procedure can take up to 1 minute and is followed by a reboot of the device.
  5. Your device's flash memory will be expanded once the reboot has finished. In order to check, log in to the WebUI and look to the 'System' widget in the 'Overview' page. Hover your mouse cursor over the 'FLASH' memory indicator; you should see an increase to the device's flash memory.

[[Category:{{{name}}} Services section]]